Cisco Systems CT2504の取扱説明書

デバイスCisco Systems CT2504の取扱説明書

デバイス: Cisco Systems CT2504
カテゴリ: コンピュータハードウェア
メーカー: Cisco Systems
サイズ: 3.86 MB
追加した日付: 1/30/2014
ページ数: 56
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスCisco Systems CT2504の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Cisco Systems CT2504に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Cisco Systems CT2504をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Cisco Systems CT2504のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Cisco Systems CT2504の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Cisco Systems CT2504 取扱説明書 - Online PDF
Advertisement
« Page 1 of 56 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Cisco Systems CT2504を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Cisco Systems CT2504の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

GETTING STARTED GUIDE
Cisco 2500 Series Wireless Controller
May 2011
Revised June 2, 2011
1 About This Guide
2 Unpacking and Preparing the Controller for Operation
3 Installing the Controller
4 Running the Bootup Script and Power-On Self Test
5 Logging into the Controller
6 Connecting to the Network
7 What’s New in Cisco Product Documentation
8 Translated Safety Warnings

ページ2に含まれる内容の要旨

1 About This Guide This guide is designed to help you install and minimally configure your Cisco 2504 Wireless Controller (2504 controller), which is part of the Cisco 2500 Series Wireless Controllers. FCC Safety Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equ

ページ3に含まれる内容の要旨

Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Statement 1015 Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you

ページ4に含まれる内容の要旨

Note Direct connection of access points to Cisco 2500 Series Wireless Controllers are not currently supported. The 2504 controller offers robust coverage with 802.11 a/b/g and delivers unprecedented reliability using 802.11n with Cisco Next-Generation Wireless Solutions and Cisco Enterprise Wireless Mesh. To best use this guide, you should have already designed the wireless topology of your network and have a working knowledge of how controllers function in a wireless LAN network. Figure 1 sh

ページ5に含まれる内容の要旨

Figure 2 shows the front panel and location of the ports and light-emitting diodes (LEDs) for the 2504 controller. Table 1 describes the components of the front panel. Note It is expected that there will be small variations in LED color intensity and hue from unit to unit. This is within the normal range of the LED manufacturer’s specifications and is not a defect. Figure 2 Front Panel and LEDs CISCO 2500 Series WIRELESS CONTROLLER Model 2504 RESET CONSOLE 12 34 PWR SYS ALM RESET CONSOLE 1 2

ページ6に含まれる内容の要旨

Callout Port and LEDs State and Description 1 GigE port and LED The Gigabit Ethernet port is an RJ-45 connector form-factor. This port is designed so that 1500 VAC rms isolation (per the 802.3 specification) is met between chassis ground and any 48V/Ethernet signal. LED description: � Green or Blinking Green—Link activity � Off—No link GigE port and LED The Gigabit Ethernet port is an RJ-45 connector 2 form-factor. This port is designed so that 1500 VAC rms isolation (per the 802.3 specif

ページ7に含まれる内容の要旨

Callout Port and LEDs State and Description RESET Reset button Pushing the Reset button reboots the system. PWR Power LED The power LED light is on when all the power conversion circuits are running normally. LED description: � Green—Power is on � Off—No power to the system System LED The system LED determines if the system is powered up. SYS LED description: � Blinking Amber—Boot-loader is active and waiting for user input from the system console. � Blinking Green—Boot-loader or booting

ページ8に含まれる内容の要旨

Note Wait at least 20 seconds before reconnecting an access point to the controller. Otherwise, the controller may fail to detect the device. Figure 3 shows the back panel and identifies its components. Table 2 describes the back panel components. Figure 3 Controller Back Panel and Components Cable Lock POWER 48VDC Slot Table 2 Controller Back Panel and Component Descriptions Ports and Slots State and Description POWER 48VDC The 48 V input power is provided via an external AC/DC adapter. Powe

ページ9に含まれる内容の要旨

2 Unpacking and Preparing the Controller for Operation Follow these steps to unpack the 2504 controller and prepare it for operation: Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container and save it. Step 3 Ensure that all items listed in the “Package Contents” section are included in the shipment. Check each item for damage. If any item is damaged or missing, notify your authorized Cisco sales representative. Pa

ページ10に含まれる内容の要旨

� Local TFTP server (required for downloading operating system software updates). Cisco uses an integral TFTP server. This means that third-party TFTP servers cannot run on the same workstation as the Cisco WCS because Cisco WCS and third-party TFTP servers use the same communication port. Initial System Configuration Information Obtain the following initial configuration parameters from your wireless LAN or network administrator: � A system (controller name), such as controller. The syste

ページ11に含まれる内容の要旨

� RADIUS server IP address, communications port, and secret if you are configuring a RADIUS server, such as 10.40.0.3, 1812, and mysecretcode. � The country code for this installation. Enter help to see a list or refer to the Cisco Wireless LAN Controller Configuration Guide for country code information. This guide is available at cisco.com. � Status of the 802.11a, 802.11b, 802.11g, or 802.11n networks, either enabled or disabled. � Status of Radio Resource Management (RRM), either enab

ページ12に含まれる内容の要旨

� Mounting the Controller on a Wall (Rack-Mount Brackets) � Mounting the Controller on a Wall (Mounting Screws) � Mounting the Controller in a Rack Mounting the Controller on a Desktop or Shelf Before mounting the controller on a desktop or shelf, install the rubber feet located in accessory kit shipped with the controller. To install the rubber feet to the controller, follow these steps: Step 1 Locate the adhesive strip with the rubber feet in the mounting-kit envelope. Step 2 Remove the

ページ13に含まれる内容の要旨

Step 3 Place the switch on the table or shelf near an AC power source. Note Allow 3 inches of space around the controller ventilation openings to prevent airflow restriction and overheating. Step 4 After the controller is mounted on a shelf or desk, perform the following tasks to complete the installation: � Connecting the Controller Console Port � Securing the Power Adapter Cable � Connecting to the Network Step 5 For configuration instructions about using the CLI setup program, see the “

ページ14に含まれる内容の要旨

Figure 5 Installing the Rack-Mount Brackets to the Sides of the Controller 1 BASE MOUNT 1 #10-32 flat head screws (mounting screws for each side of the controller) 1 Step 2 Mount the 2504 controller on the wall with the front panel facing down, as shown Figure 6. For the best support of the controller and cables, make sure the controller is attached securely to wall studs or to a firmly attached plywood mounting backboard. 14 282083

ページ15に含まれる内容の要旨

Figure 6 Mounting the Controller on the Wall 1 2 3 1 Front panel (facing down) 3 Wall mounting screws #10-32 flat head screws 2 Step 3 After the controller is mounted on the wall, perform the following tasks to complete the installation: � Connecting the Controller Console Port � Securing the Power Adapter Cable � Connecting to the Network Step 4 For configuration instructions about using the CLI setup program, see the “Running the Bootup Script and Power-On Self Test” section on page 23. M

ページ16に含まれる内容の要旨

Warning Read the wall-mounting carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 To mount the controller on a wall using mounting screws, follow these steps: Step 1 Mark the location of the mounting screws on the wall. Use the mount hole locations on the back of the controller for placement of the mounting screws (Figure 7). (The mount holes ar

ページ17に含まれる内容の要旨

Step 4 Place the controller onto the mounting screws and slide it down until it lock into place, as shown in Figure 8. Note The front panel of the controller should be facing down. Figure 8 Place the Controller on the Mounting Screws 2 1 2 1 Front panel (facing down) 2 Mounting screws Step 5 After the controller is mounted ion the wall, perform the following tasks to complete the installation: � Connecting the Controller Console Port � Securing the Power Adapter Cable � Connecting to the N

ページ18に含まれる内容の要旨

Step 6 For configuration instructions about using the CLI setup program, see the “Running the Bootup Script and Power-On Self Test” section on page 23. Mounting the Controller in a Rack To mount the 2504 controller in a 19-inch equipment rack, you can order an optional Optional Rack Mount kit (AIR-CT2504-RMNT). Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines

ページ19に含まれる内容の要旨

Figure 9 Attaching the 19-Inch Brackets to the Side of the Controller. 1 RACK MOUNT 1 1 #10-32 flat head screws (mounting screws for each side of the controller) Step 2 After the brackets are attached to the sides of the controller, insert the controller into the 19-inch rack. Use either the 10-32 pan-head screws or the 12-24 slotted head screws to secure the controller in the rack, as shown in Figure 10. 19 282082

ページ20に含まれる内容の要旨

Figure 10 Mounting the Controller in a 19-Inch Rack 1 #10-32 pan-head screws or #12-24 slotted head screws 1 Step 3 After the controller is mounted in the rack, perform the following tasks to complete the installation: � Connecting the Controller Console Port � Securing the Power Adapter Cable � Connecting to the Network Step 4 For configuration instructions about using the CLI setup program, see the “Running the Bootup Script and Power-On Self Test” section on page 23. 20 282086


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Cisco Systems 5545-X 取扱説明書 コンピュータハードウェア 0
2 Cisco Systems 5555-X 取扱説明書 コンピュータハードウェア 0
3 Cisco Systems C170 取扱説明書 コンピュータハードウェア 6
4 Cisco Systems 5585-X 取扱説明書 コンピュータハードウェア 3
5 Cisco Systems 5525-X 取扱説明書 コンピュータハードウェア 1
6 Cisco Systems 1130AG 取扱説明書 コンピュータハードウェア 7
7 Cisco Systems 5512-X 取扱説明書 コンピュータハードウェア 0
8 Cisco Systems 8900 取扱説明書 コンピュータハードウェア 0
9 Cisco Systems 2500 取扱説明書 コンピュータハードウェア 10
10 Cisco Systems M170 取扱説明書 コンピュータハードウェア 0
11 Cisco Systems 5580 取扱説明書 コンピュータハードウェア 1
12 Cisco Systems ASA5585S60P60SK9 取扱説明書 コンピュータハードウェア 0
13 Cisco Systems AVS 3120 取扱説明書 コンピュータハードウェア 0
14 Cisco Systems Cisco Wave 694 Application Acceleration Appliance WAVE694K9 取扱説明書 コンピュータハードウェア 2
15 Cisco Systems Cisco MGX 8800 取扱説明書 コンピュータハードウェア 1
16 Sony MSAKIT-PC4A 取扱説明書 コンピュータハードウェア 2
17 Sony MRW62E-S1 2694866142 取扱説明書 コンピュータハードウェア 5
18 Philips MATCH LINE 9596 取扱説明書 コンピュータハードウェア 17
19 Sony 64GB SDHC Class 10 Memory Card Readers SF32UY 取扱説明書 コンピュータハードウェア 1
20 Philips PSC702 取扱説明書 コンピュータハードウェア 1