ページ1に含まれる内容の要旨
.
TABLE OF CONTENTS
FOR YOUR SAFETY -------------------------------------------------- 1
SAFETY PRECAUTIONS --------------------------------------- 2
SPECIAL NOTES ON LCD MONITORS -------------------- 3
BEFORE YOU OPERATE THE MONITOR ---------------------- 3
FEATURES -------------------------------------------------------- 3
PACKING LIST --------------------------------------------------- 3
INSTALLATION INSTRUCTIONS ---------------------------- 4
CONTRO
ページ2に含まれる内容の要旨
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Stateme nt WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generat
ページ3に含まれる内容の要旨
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold w ith the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit in
ページ4に含まれる内容の要旨
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes o
ページ5に含まれる内容の要旨
INSTALLATION INSTRUCTIONS SWIVEL BASE IVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allo ws operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3. Connect the AC-power cord into your LCD monitor’s AC-power
ページ6に含まれる内容の要旨
CONTROLS AND CONNECTORS CABLE CONNECTIONS Turn off your computer before performing the procedure belo w. 1 Plug the power cable of your monitor into a nearby outlet. Plug the other end of the power cord into the PC port. 2. Connect one end of the 15-pin VGA cable to the back of the monitor and connect the other end to the computer’s D-Sub port. 3. Turn on your monitor and computer. 2 1 Figure 2 Connecting Cables 1. Power Cable 2. Signal Cable 5
ページ7に含まれる内容の要旨
ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. • Hold the stand so you do not topple the monitor when you change the monitor’s angle. • You are able to adjust the monitor’s angle from -5° to 15 °. 1 5 -5 Figure 3 NOTES • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. • Careful attention is required not to
ページ8に含まれる内容の要旨
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • Press the power button to turn on the monitor position. The power indicator will light up. 1 2 3 4 5
ページ9に含まれる内容の要旨
FRONT PANEL CONTROL • /Power Button: Press this button to turn the monitor ON or OFF, And display the monitor’s state. • Power Indicator: Green — Power On mode. Orange — Stand by mode. • MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON. • <: navigate through adjustment icons when OSD is ON or adjust a function when function is activated.
ページ10に含まれる内容の要旨
HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window . 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function. 5. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-4. I. Analog-Only Model 9
ページ11に含まれる内容の要旨
ADJUSTING THE PICTURE The descriptions for function control LEDS Sub Main Sub Menu Menu Description Menu Icon Item Icon Adjusts the contrast between Contrast the foreground and background of the screen image. Adjusts the background brightness of Brightness the screen image. Focus Adjusts picture Focus. Clock Adjusts picture Clock. H. Position Adjust picture Focus. V. Position Adjust picture Clock. N/A Warm Set the color temperature to
ページ12に含まれる内容の要旨
N/A Language Multi-language selection. H. Position Adjust the horizontal position of the OSD. V. Position Adjust the vertical position of the OSD. OSD Adjust the OSD timeout. Timeout N/A DDC/CI Turn ON/OFF DDC/CI support. N/A Information Show the resolution, H/V frequency and input port of current iput timing. Clear each old status of Auto-configuration N/A Reset and set the color temperature to Cool. N/A Exit Save user adjustment and OSD disapp
ページ13に含まれる内容の要旨
PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. 2 The DDC2B is a bidirectional data channel based on the I C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-FUNCT
ページ14に含まれる内容の要旨
TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave *Move electrical devices that may cause pattern is present in the
ページ15に含まれる内容の要旨
Screen image is not centered or sized *Adjust pixel frequency (CLOCK) and properly . FOCUS or press hot-key (AUTO) Picture has color defects *Adjust RGB color or select color (white does not look white) temperature Horizontal or vertical disturbances on *Use win 95/98 shut-down mode the screen Adjust CLOCK and FOCUS or perform hot- key (AUTO-key). CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows
ページ16に含まれる内容の要旨
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is properly connected, If the connector is loose, tighten the connector’s screw s. 2. Check the signal -cable connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table (See page 18). 15
ページ17に含まれる内容の要旨
APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 17" Pixel pitch 0.255mm( H ) × 0.255mm( V ) 2 Brightness 250cd/m (Typical) Contrast 700:1 (Typical) Viewable angle 140° (H) 130° (V) Response time 8 ms Input Video R,G,B Analog Interface H-Frequency 55.469kHz – 70.635kHz V-Frequency 60-75Hz Display Colors 262144 Colors Dot Clock 170MHz Max. Resolution
ページ18に含まれる内容の要旨
Switch • Auto Adjust Key • < • > • Power Button • MENU External Controls: Functions • Contrast • Brightness • Focus • Clock • H.Position • V.Position • Language • DDC/CI ON/OFF • (Warm) Color • (Cool) Color • RGB Color temperature • Reset • OSD position . timeout • Display information • Exit Power Consumption ( Maximum ) 45 Watts Regulatory Compliance CUL, FCC, VCCI, CCC, MPR II, CE, , ISO13406-2 TÜV/GS 17
ページ19に含まれる内容の要旨
Preset Display Modes STANDARD RESOLUTION HORIZONTAL VERTICAL FREQUENCY(KHz) FREQUENCY(KHz) DOS 720x400 31.469 70.087 VESA VGA 640x480 31.469 59.940 640x480 35.000 66.667 640x480 37.861 72.809 640x480 37.500 75.000 SVGA 800x600 35.156 56.250 800x600 37.879 60.317 800x600 48.077 72.188 800x600 46.875 75.000 832x624 49.726 74.551 XGA 1024x768 48.363 60.004 1024x768 56.476 70.069 1024x768 60.023 75.029 SXGA 1152x864 67.500 75.000 1280x1024 64.000 60.000 1280x1024 8
ページ20に含まれる内容の要旨
CONNECTOR PIN ASSIGNMENT 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. MonitorGround 4. Monitor Ground 12. DDC-Serial Data 5. DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground 19
