ページ1に含まれる内容の要旨
INSTALLATION/OPERATION
400 Series Flat Panel
LCD Monitors
C2927M-C (12/06)
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . .
ページ4に含まれる内容の要旨
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the pola
ページ5に含まれる内容の要旨
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provi
ページ6に含まれる内容の要旨
Description The 400 Series high performance LCD monitors are designed specifically for the security industry and provide high quality display of video or computer signals using multiple inputs. These 15-, 17-, and 19-inch monitors use a color, thin film transfer (TFT) active matrix LCD panel that automatically adapts to the appropriate input resolution. The 400 Series is distinguished by many performance-enhancing features such as a 3-D digital comb filter, DVI (digital visual interface) input
ページ7に含まれる内容の要旨
PACKAGE CONTENTS 1 15-, 17-, or 19-inch TFT LCD monitor 1 VGA cable with 15-pin, D-sub connector 1 US standard power cable 1 EU standard power cable 1 DVI cable 1 USB cable (Type A to B) 1 Remote control unit 2 AA batteries 1 Installation/Operation manual VGA CABLE WITH 15-PIN, D-SUB CONNECTOR TFT LCD MONITOR US STANDARD DVI CABLE POWER CABLE INSTALLATION REMOTE CONTROL UNIT 2 AA BATTERIES EU STANDARD USB CABLE (TYPE A TO B) OPERATION MANUAL POWER CABLE Figure 1. Parts List Illustration C2927
ページ8に含まれる内容の要旨
Installation The monitor can be placed on any flat surface (desk or table), or it can be rack mounted or wall mounted. NOTE: Only use a recommended rack mount or wall mount kit, such as the PMCL-RM15, PMCL-RM17, PMCL-RM19, or PMCL-WM. To rack- mount or wall-mount the monitor, follow the instructions supplied with the mount kit. Refer to manual C2220M for the rack mount kit instructions or C2219M for the wall mount kit instructions. DESKTOP STAND You can manually adjust the 400 Series monitor t
ページ9に含まれる内容の要旨
1. AC IN: Can be connected to a 100-240 VAC, 50/60 Hz source. 2. DC OUT: Can output 12 VDC, 0.5 A (continuous), 50/60 Hz. 3. DC IN: Can be connected to an external 12 VDC, 5 A source. 4. VGA IN: Can be connected to the VGA cable (supplied). 5. DVI IN: Can be connected to the DVI cable (supplied). 6. USB: The USB-A 2.0 downstream port. It can be used to connect to such peripherals as a USB camera or USB key. 7. USB: The USB-A 2.0 downstream dual port. It can be used to connect to such peripherals
ページ10に含まれる内容の要旨
VIDEO AND POWER CONNECTIONS Refer to Figure 2 for video, audio, power, and other connections. 1. Connect the video cable (refer to Table A for video coaxial requirements.) a. Connect video cables as follows, depending on the input source. For composite, connect to the BNC video input labeled VIDEO 1 IN on the back panel of the monitor. If the installation requires a second video input, connect a video cable to the BNC video input labeled VIDEO 2 IN. (Inputs are auto-terminating. If the correl
ページ11に含まれる内容の要旨
PMCL400 2.0 CAMERA S-VIDEO DVR OUT IN AUDIO IN L R L R AUDIO AUDIO SOURCE AUDIO OUT CAMERA VIDEO 1 DVR OUT IN OUT IN DVR VIDEO 2 CAMERA Figure 3. Looping Operation: One Monitor with External Video Equipment PMCL400 PMCL400 PMCL400 2.0 2.0 2.0 DVR CAMERA S-VIDEO S-VIDEO S-VIDEO OUT IN OUT IN OUT IN AUDIO IN AUDIO IN AUDIO IN L R L R L R L R L R L R AUDIO AUDIO SOURCE AUDIO OUT AUDIO OUT AUDIO OUT CAMERA VIDEO 1 VIDEO 1 VIDEO 1 DVR OUT IN OUT IN OUT IN OUT IN OUT IN OUT IN VIDEO 2 VIDEO 2 VIDEO 2
ページ12に含まれる内容の要旨
Operation INSTALLING REMOTE CONTROL BATTERIES PRESS AND SLIDE TO REMOVE Figure 5. Battery Installation Refer to Figure 5 for the following procedure. 1. Open and remove the battery cover on the back of the remote control. 2. Install two AA size batteries (supplied). Match the + and – signs on the batteries to the signs on the battery compartment. 3. Close the battery cover. Make sure the lock snaps closed. WARNING: Dispose of batteries in a designated disposal area. Do not throw batteries in
ページ13に含まれる内容の要旨
FRONT PANEL CONTROLS CH Figure 6. Front Panel Controls 1. Selects the input signal and swaps the main and PIP displays when PIP is active. 2. Decreases the value of a selected menu item and accesses the brightness control when no PIP or menu is active. It can reposition PIP when PIP is active. 3. Increases the value of a selected menu item, and it enables or disables PIP when no menu is active. 4. Moves the highlighter downward through a menu. 5. Moves the highlighter upward throug
ページ14に含まれる内容の要旨
REMOTE CONTROL FUNCTIONS PIP SWAPLOCATE CH
VOL Figure 7. Remote Control Functions 1. Turns on or off power to the monitor. 2. Selects the previous channel. 3. Selects the next channel. 4. Increases the audio volume. 5. Decreases the audio volume. 6. Moves the PIP location to the next location (upper left, upper right, lower right, lower left, middle). 7. Swaps the PIP image with the main image or the main image with the PIP image. 8. Selects the PIP function. 9. Mo
ページ15に含まれる内容の要旨
OSD CONTROL MENUS Unless otherwise noted, the menus are the same for the PMCL415, PMCL417, and PMCL419. Since different options are available for different input types, some menus have a video mode and a VGA mode. Some options may be unavailable and are grayed out. NOTE: There is no reset feature to return the monitor to factory defaults. To use the menus: 1. Press the menu button to access the Main menu. 2. Use the up and down arrow buttons to highlight a selection. 3. Press the menu button t
ページ16に含まれる内容の要旨
VIDEO MENU (VGA MODE) Contrast VIDEO MENU VIDEO MENU Contrast 50 AUDIO MENU Brightness Brightness 50 SCREEN MENU Color SOURCE MENU Tint OPTION MENU Sharpness EXIT MENU Noise Reduction weak Return Menu Figure 9. Video Menu (VGA Mode) If PIP is active in VGA mode, these controls affect PIP and not the Main Display. Video Menu (VGA Mode) Field Definitions Contrast: Adjusts the white level of the video screen image. Brightness: Adjusts the black level of the video screen image. AUDIO
ページ17に含まれる内容の要旨
SCREEN MENU (VGA MODE) Clock 50 Display Mode Aspect VIDEO MENU Clock H Position AUDIO MENU 7 H Position SCREEN MENU V Position V Position Phase 49 SOURCE MENU Smoothing OPTION MENU Phase Auto Sync 10 EXIT MENU Color Temperature DEFAULT Smoothing Return Menu 2 Auto Position 9300K 7500K 6500K Default Figure 12. Screen Menu (VGA Mode) Screen Menu (VGA Mode) Field Definitions Clock: Adjusts the horizontal size of the screen image. H Position: Moves the screen image left or right.
ページ18に含まれる内容の要旨
SOURCE MENU (VGA MODE) VGA Main Display Source: VGA DVI VIDEO MENU PIP Display source: OFF VIDEO-1 VIDEO-2 AUDIO MENU Return Menu SVIDEO SCREEN MENU SOURCE MENU OPTION MENU VIDEO-1 VIDEO-2 EXIT MENU SVIDEO OFF Figure 14. Source Menu (VGA Mode) Source Menu (VGA Mode) Field Definitions Main Display Source: Select one: VGA, DVI, VIDEO-1, VIDEO-2, SVIDEO. PIP Display source: Select one: VIDEO-1, VIDEO-2, SVIDEO, OFF. (Some choices will be shaded depending on your Main Display Source sel
ページ19に含まれる内容の要旨
MENU DEFAULT VALUES Refer to the following default values if you need to manually return the monitor to the factory settings. Video Menu Contrast 50 Brightness 50 Color 50 Tint 0 Sharpness 2 Noise Reduction Strong Audio Menu Volume 8 Screen Menu Display Mode Aspect Clock 50 H Position 50 V Position 50 Phase 0 Smoothing 0 Auto Sync (no default setting) Color Temperature 9300K Source Menu Main Display Source VGA PIP Display Source OFF Option Menu Menu Language English Menu Timeout 15 Menu Backgrou
ページ20に含まれる内容の要旨
Supported Input Modes Mode Resolution H Freq (kHz) V Freq (Hz) 0 720 x 350 31.469 70.087 1 640 x 480 31.469 59.940 2 640 x 480 35.000 66.667 3 640 x 480 37.861 72.809 4 640 x 480 37.500 75.000 5 720 x 400 31.469 70.087 6 800 x 600 35.156 56.250 7 800 x 600 37.879 60.317 8 800 x 600 48.077 72.188 9 800 x 600 46.875 75.000 10 1024 x 768 48.363 60.004 11 1024 x 768 60.023 75.029 20 C2927M-C (12/06)
