ページ4に含まれる内容の要旨
User’s Manual However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment int
ページ5に含まれる内容の要旨
Preface For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. “Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du
ページ6に含まれる内容の要旨
User’s Manual 5. Do not remove the cover or attempt to service this unit by yourself. You may void the warranty. Servicing of any nature should be performed only by an authorized technician. 6. Safe storage of the LCD Monitor is in a range of minus 20 to plus 65 degrees Celsius (68°F-149°F). Storing your LCD Monitor outside this range could result in permanent damage. 7. If any of the following occurs, immediately unplug your Monitor and call an authorized technician. • The power or
ページ7に含まれる内容の要旨
Table of Contents TABLE OF CONTENTS PREFACE..................................................................................................................... I TABLE OF CONTENTS............................................................................................. I CHAPTER 1 .................................................................................................................1 Your New LCD Monitor! .................................................................
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
Chapter 1 CHAPTER 1 The LCD Monitor Your New LCD Monitor! Your LCD Monitor has been designed to be versatile, ergonomic and user- friendly. The LCD Monitor is capable of displaying most standards, from 640 x 480 VGA to 800 x 600 SVGA. The digital controls located on the front panel allows the user to easily adjust the Monitor’s display parameters. The LCD Monitor’s small footprint allows you more room in your workspace for other peripherals. Lightweight and compact, the LCD Monitor
ページ10に含まれる内容の要旨
User’s Manual • AC Adapter • Power cord • This user’s manual If you find that any of these items are missing or appear damaged, contact your dealer immediately. Do not throw away the packing material or shipping carton in case you need to ship or store the LCD Monitor in the future. Identifying Components The LCD Monitor has been designed to provide easy access to all controls and peripheral ports. The following figures will help you identify the LCD Monitor’s controls and ports.
ページ11に含まれる内容の要旨
Chapter 1 nd select the function group. The 2 button allows you to select one of the control functions within each function group. 3. Adjustment Control Buttons These two buttons allow you to adjust the selected control function to accommodate your specific working environment. Press the upper button to increase the setting of the selected control function and press the lower button to decrease the setting of the selected control function. 4. Power Switch Push the power switch to tu
ページ12に含まれる内容の要旨
User’s Manual The LCD Monitor — Rear View Figure 1-2: LCD Monitor’s Rear Ports 1. LCD Monitor’s VGA Connector This 1.5 meter cable has two 15-pin D-Sub VGA connectors used to connect the monitor to your PC’s VGA card. 2. DC Power Jack Connect the AC adapter cable to this jack. 3. RS232 Connector for Optional Touch Screen Connect this RS232 connector to your PC’s RS232 9-pin serial port connector to use the Optional Touch Screen. A RS232 cable is provided with the Optional Touch Scr
ページ13に含まれる内容の要旨
Chapter 1 Adjusting the Viewing Angle Your LCD Monitor is designed to allow you to adjust it to a comfortable viewing angle. The LCD Monitor’s angle setting range is from -5° to 25°. Please see Figure 1-3. Figure 1-3: Angle Settings • When positioning the equipment, make sure that the main ports and sockets are easily accessible. • Do not place your LCD Monitor close to a heat source. • Do not place the LCD Monitor in direct sunlight or near a window. Moisture and dire
ページ14に含まれる内容の要旨
User’s Manual Connecting AC Power Please refer to the following instructions for connecting AC power to the LCD Monitor. Plug the female end of the power cable into the AC-adapter. Plug the male end of the power cord into a wall socket. The plug on the power cable will vary according to the electrical standard in your area. Please refer to Figure 1-4. Figure 1-4: The AC Adapter Connect the power connector of the adapter into the jack of the LCD Monitor. The AC power jack is loc
ページ15に含まれる内容の要旨
Chapter 1 Connecting Video Turn off your PC and the LCD Monitor before connecting your LCD Monitor to the computer. Connect the VGA signal cable to the D-sub VGA connector located at the rear of the monitor. Connect the other end of the signal cable to the PC’s VGA port. Please refer to Figure 1-6. Figure 1-6: Connecting the LCD Monitor to the PC Make sure the signal cable heads are securely connected to the VGA ports of your PC and Monitor. Tighten the connecting screws to ensu
ページ16に含まれる内容の要旨
User’s Manual Connect the RS232 connector of the RS232 cable provided with the optional touch screen package to the RS232 Mini-Din port at the back of the LCD Monitor. Please refer to Figure 1-7. Connect the 9-pin RS232 connector end of the RS232 cable provided with the optional touch screen package to the 9-pin RS232 serial port at the back of your PC. Please refer to Figure 1-7. Figure 1-7: Connecting the Optional Touch Screen Cable Power Management System The LCD Monitor complie
ページ17に含まれる内容の要旨
CHAPTER 2 The Display Controls The LCD Monitor’s Display Controls This chapter covers the LCD Monitor’s On Screen Display (OSD). Using the OSD, you can adjust the contrast, brightness, display position, display clarity, and color temperature. You can also set OSD parameters. Please read this chapter carefully to get the most out of your LCD Monitor. Adjusting the Monitor’s Display The LCD Monitor features an intuitive, menu-driven, On-Screen Display (OSD). You can access the OSD any
ページ18に含まれる内容の要旨
User’s Manual The control functions are grouped into four categories as shown on the Main Menu. Continue pressing the first button to scroll through the function group. Press the second button to scroll through the functions of each function group. Each item is covered below. Main Function Group To control the contrast, brightness, etc. (BASIC SETTING) To control the display size, position, clock and (POSITION) phase, etc. To control OSD positions and to give the (MISCELLANEO
ページ19に含まれる内容の要旨
Chapter 2 To adjust the display position vertically. (V-POSITION) To select either Graph or Text expansion method. Only (GRAPH/TEXT) available in 720 x 400/640 x 480 resolutions. To set the function parameters in the position menu to (RESET) the default values. (Miscellaneous Menu) To adjust the horizontal position of the OSD (OSD H-POSITION) menu. To adjust the vertical position of the OSD menu. (OSD V-POSITION) The OSD Menu display time can be set at 5, 10, (MEN
ページ20に含まれる内容の要旨
User’s Manual Note: 1. No Signal coming When the monitor is ON and there is no Video signal received, the following message will be displayed. 2. Signal out of monitor’s supported range (Please refer to tht attached Addendum) When the frequency range is out of the monitor’s specifications, the display will show the following message on two cases: Case 1: The incoming resolution is lower than or equal to 800x600. In this case, the screen display will not be centered and a warn
ページ1に含まれる内容の要旨
PL120/PT120
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Preface PREFACE About this manual This manual is designed to assist you in setting up and using the LCD monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or
