ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
User’s Manual 2 Index Main Page On-Screen Display General Highlight Zone MouScreen ™ S/W Safety Instructions Troubleshooting Natational Check List Power Q & A Installation Self-Test Feature Check Cleaning Other Introduction Specifications Unpacking General Specifications Front Preset Display Modes Rear PowerSaver Bottom Setup Information Connecting Your Monitor Service Installing the Monitor Driver Terms — Windows 2000 Regulatory — Other Operating System Natural Color Base Installation MouScree
ページ3に含まれる内容の要旨
User’s Manual 3 Safety Instructions Notational Warning/Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equip- ment. Notation Conventions Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock
ページ4に含まれる内容の要旨
User’s Manual 4 Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the flourescent substance on the inside of the CDT. Do not use a damaged or loose plug. This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug w
ページ5に含まれる内容の要旨
User’s Manual 5 Safety Instructions Power Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. Failure to do so may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. This may cause a fire.
ページ6に含まれる内容の要旨
User’s Manual 6 Safety Instructions Installation Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Put your monitor in a location with low humidity and a mini- mum of dust. An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. This may cause damage to the product or human body. Place the monitor on a flat and stable surface. The monitor can cause injury by falling. Set down the monit
ページ7に含まれる内容の要旨
User’s Manual 7 Safety Instructions Installation Do not place the monitor face down. The CDT surface may be damaged. Do not use the monitor without the monitor stand. It could break down or cause a fire due to bad ventilation. If the monitor must be used without the supplied stand, take steps to insure proper ventilation.
ページ8に含まれる内容の要旨
User’s Manual 8 Safety Instructions Clean When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using. Do not
ページ9に含まれる内容の要旨
User’s Manual 9 Safety Instructions Other Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire. Do not place any heavy objects on the monitor. This m
ページ10に含まれる内容の要旨
User’s Manual 10 Safety Instructions Other Do not try to move the monitor by pulling on the wire or the sig- nal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable. Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury. Keep
ページ11に含まれる内容の要旨
User’s Manual 11 Introduction Unparking Monitor and Stand Power Cord Stand Signal Cable(Option) Quick Setup Guide (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Warranty Card (Not available in all locations) User's Guide and Driver Installation CD USB Cable USB Hub (Option)
ページ12に含まれる内容の要旨
User’s Manual 12 Introduction Front 1. Highlight button The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by emphasizing a certain area on the screen. 2. Exit button Use this button to Exit the active menu or the OSD. 3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item. 5. Power indicator This light glows green during normal operation, and blin
ページ13に含まれる内容の要旨
User’s Manual 13 Introduction Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 2. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. BNC Connectors (Option) Connect the signal cable to the BNC signal port on the back of your monitor. 4. USB Connector Connect the USB cable to the USB port o
ページ14に含まれる内容の要旨
User’s Manual 14 Introduction Bottom 1. Signal Cable Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 2. Power Port Connect the power cord for your monitor to the power port on the back of the monitor. 3. Tilt/Swivel Base You can separate the base from the monitor.
ページ15に含まれる内容の要旨
User’s Manual 15 Setup Connecting Your Monitor 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter (Adapter not included). A PC-compatible computer does not need an adapter. 4. C
ページ16に含まれる内容の要旨
Setup When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (Europe) http://www.samsungmonitor.com/ (USA) http://www.sec.co.kr/ (Korea) http:/
ページ17に含まれる内容の要旨
Setup Windows XP/2000 1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button. 4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage h
ページ18に含まれる内容の要旨
Setup When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (Europe) http://www.samsungmonitor.com/ (USA) http://www.sec.co.kr/ (Korea) http:/
ページ19に含まれる内容の要旨
Setup 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
ページ20に含まれる内容の要旨
Setup Thi This monit itor d driiver iis und der certif tifyiing MS MS llogo,and d thi this iinsttall llati tion d don't 't d damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. ® ® Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK
