ページ1に含まれる内容の要旨
User’s Guide
Compaq 7020 Flat Panel Monitor
Document Part Number: 254041-003
April 2002
Enhanced for accessibility
ページ2に含まれる内容の要旨
© 2002 Compaq Information Technologies Group, L.P. Compaq, the Compaq logo are trademarks of Compaq Information Technologies Group, L.P. in the United States and/or other countries. Microsoft, MS-DOS, Windows, Windows NT are trademarks of Microsoft Corporation in the United States and/or other countries. All other product names mentioned herein may be trademarks of their respective companies. Compaq shall not be liable for technical or editorial errors or omissions contained herein. The
ページ3に含まれる内容の要旨
1 Installation Unpacking Before unpacking the monitor, prepare a suitable workspace for your monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that monitor has enough space around it for sufficient airflow. Though the monitor uses very little power, some ventilation is needed to ensure that the monitor does not become too hot. After you unpack the monitor box, make sure that the following items were included in the box: ■ Monitor ■ 1.5
ページ4に含まれる内容の要旨
Installation Viewing Angle Adjustment The monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted as follows: Top (-5°~ +35°) & Left / Right (-45° to +45°). Figure 1-1 CAUTION: Do not force the monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the monitor and monitor stand. 1-2 Compaq 7020 Flat Panel Monitor User’s Guide
ページ5に含まれる内容の要旨
Installation Detaching Monitor from Its Stand 1. Remove the rear panel 1 from the monitor. (see Fig. 1-2) 2. Remove the rear support panel 2 from the swivel base support column. 3. Unscrew screws 3 the swivel base support column 4. Figure 1-2 Compaq 7020 Flat Panel Monitor User’s Guide 1-3
ページ6に含まれる内容の要旨
Installation Connecting the Display to the Swivel Base Before connecting the display to the swivel base support column, please refer to Fig.1-2. The rear of this display has four integrated 4 mm, 0.7 pitch, threaded holes, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-3. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2.1 and 2.1.3, version 1, dated 13 November 1997). Figure 1-3 1-4 Compaq
ページ7に含まれる内容の要旨
Installation Cable Installation Please follow these instructions to install the cables. 1. Remove the back panel 1 from the rear of the monitor. (See Fig. 1-4). 2. Remove the rear support panel 2 from the swivel base support column. 3. Place the signal cable, the DC power cable and the audio cable into their correct respective grooves 3. Figure 1-4 Compaq 7020 Flat Panel Monitor User’s Guide 1-5
ページ8に含まれる内容の要旨
Installation Connecting the Display to Your Computer 1. Power off your computer. 2. Connect one end of the signal cable to the monitor's VGA port or DVI port (digital models only). (See Fig. 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. 4. Make sure both connections are secure. Figure 1-5 WARNING: This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is in
ページ9に含まれる内容の要旨
Installation Connecting the AC Power 1. Connect the power cord to the AC adapter. (See Fig. 1-6) 2. Connect the AC adapter's DC output connector to the DC Power Jack of the monitor. 3. Connect the power cord to an AC power source. Figure 1-6 WARNING: We recommend to install a "Surge Protector" device between the AC Adapter and the electrical wall outlet for adding protection against power surges to prevent the effects of sudden voltage variations from reaching the monitor. Sudde
ページ10に含まれる内容の要旨
Installation Connecting the Audio Cable The instructions in this section apply only to monitor models featuring speakers. 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. (See Fig. 1-7) 2. Connect the other end of the audio cable to the monitor's " LINE IN " jack. Figure 1-7 1-8 Compaq 7020 Flat Panel Monitor User’s Guide
ページ11に含まれる内容の要旨
Installation Setting Up the Monitor 1. Make sure the AC Adapter is connected to the monitor. 2. Turn on the monitor's power switch, located on the bezel of the monitor. Power Management System The monitor supports one low power mode. When the monitor is in the low power mode, the monitor screen will be blank and the power LED indicator will light amber. Compaq 7020 Flat Panel Monitor User’s Guide 1-9
ページ12に含まれる内容の要旨
2 Display Controls User Controls The monitor features several function controls and indicators: Figure 2-1 1 *Stereo Speakers PC Audio Stereo output. 2 External Headphone The monitor speakers will be Jack (speaker models disabled when using an external only) headphone or external speakers. 3 Menu Button Press the menu button to view the OSD (On Screen Display) menu selection. 4 Adjustment Control Press the left button (-) to Buttons decrease the OSD setting and press the righ
ページ13に含まれる内容の要旨
Display Controls DC Power-On Indicator LED lights Green color - Power 5 is ON. LED lights Amber - Monitor is in “Power Saving Mode”. LED is off - Power is OFF. DC Power Switch Press the power switch to 6 switch the monitor ON/OFF. *Speaker Volume Control Increase Volume - Turn the 7 knob clockwise. Decrease Volume - Turn the knob counter clockwise. * Speaker models only Adjusting the Monitor’s Display This monitor features an "Intellectual-AUTO" function, which stores up to 1
ページ14に含まれる内容の要旨
Display Controls The firmware may have been updated to a later version. However, the version number shown on all OSD menus in this guide will remain Ver. 1.00. The following menus show the functions at each level: OSD Menu Main Menu Advanced Menu Menu Level 3 Brightness Adjustment Scale Contrast Adjustment Scale Image Control Auto Adjustment Adjustment Message Horizontal Image Position Adjustment Scale Vertical Image Position Adjustment Scale Clock Adjustment Scale Clock Phase
ページ15に含まれる内容の要旨
Display Controls OSD Menu Main Menu Advanced Menu Menu Level 3 Management Power Saver On/Off Selection Power On Recall On/Off Selection Mode Display On/Off Selection Serial Number Display serial number Sleep Timer Timer Set Menu Basic Menu Cancel Save and Return OSD Control Horizontal OSD Position Adjustment Scale Vertical OSD Position Adjustment Scale OSD Timeout Adjustment Scale OSD Transparency Adjustment Scale Cancel Save and Return Factory Reset Yes No Exit 2-4 Comp
ページ16に含まれる内容の要旨
Display Controls How to Adjust Settings 1. To launch the on-screen display menu, complete the following: ❏ Basic Main Menu: To display the Basic Main Menu, press the Menu button on the monitor front panel. ❏ Advanced Main Menu: Select “Advanced Menu” from the Basic Main Menu to display the Advanced Main Menu shown below. Compaq 7020 Flat Panel Monitor User’s Guide 2-5
ページ17に含まれる内容の要旨
Display Controls After the Advanced Main Menu has been selected, it remains the default on-screen display each time the monitor is powered on until the Basic Main Menu option is selected again. 2. To select an item from the Basic Main Menu, scroll down and highlight an item by pressing the Minus (-) button located on the monitor front panel. To reverse or back up, press the Plus (+) button. 3. Highlight your choice and press the Menu button again. 4. Adjust the Advanced Main Menu disp
ページ18に含まれる内容の要旨
Display Controls amber. When the monitor is in the reduced power state, the monitor will utilize less than 5 watts of power. There is a brief warm up period before the monitor will return to its normal operating mode. Refer to your computer manual for instructions on setting energy saver features (sometimes called power management features). By selecting settings in the monitor’s Energy Saver utility, you can also program the monitor to enter the reduced power state at a predetermined ti
ページ19に含まれる内容の要旨
3 Technical Information Monitor Specifications Screen Size 17.0” (43 cm) Display Type Active matrix color TFT LCD Resolution 1280 x 1024 Display Dot 1280 x (RGB) x 1024 Display Area (mm) 337.92 x 207.34 (HxV) Lamp Voltage 720 Vrms (typical) Lamp Current 6.0 mA rms. (typical) Input Signal Analog RGB 0.7 Vp-p Input Impedance 75 Ohm ± 2% Polarity Positive Amplitude 0 - 0.7 ± 0.05 Vp Multi-mode Supported Horizontal Frequency: 30 - 80 KHz Vertical Frequency: 56 - 75 Hz Dime
ページ20に含まれる内容の要旨
Technical Information Monitor Specifications Power Input Voltage 100 to 240V AC Frequency 50-60 Hz Environmental Operating temperature: 5°C to 40°C/41°F to 104°F Considerations Humidity: 20% to 80% (non-condensing) Storage temperature: -20°C to 60° C/-4°F to140° F Humidity: 5% to 85% (non-condensing) Power Consumption 40 W, 50 W with speakers Preset Display Modes Mode H. Freq. V. Freq. Pixel Sync. (KHz) (Hz) Clock Polarity (MHz) (H/V) VGA, 640 x 480 31.469 59.940 25.175 -/
