ページ1に含まれる内容の要旨
EN-5100e
EN-5100e
15 inch TFT LCD Monitor
User’s
Manual
by Envision Peripherals, Inc.
www.ENVISIONmonitor.com
Before operating your monitor, please read this
manual thoroughly.
EN-5100e
1
31MY02
ページ2に含まれる内容の要旨
For Your Safety EN-5100e FCC Statement Notice This equipment has been tested and found to 1. The changes or modifications not expressly comply with the limits for a Class B digital device, approved by the party responsible for pursuant to Part 15 of the FCC Rules. These limits compliance could void the user's authority to are designed to provide reasonable protection operate the equipment. against harmful interference in a residential 2. Shielded interface cables and AC power cord, if insta
ページ3に含まれる内容の要旨
For Your Safety EN-5100e The monitor is equipped with a three-pronged Precautions grounded plug, a plug with a third (grounding) Do not use the monitor near water, e.g. near a pin. As a safety feature, this plug will only fit into bathtub, washbowl, kitchen sink, laundry tub, a grounded power outlet. If your outlet does not swimming pool or in a wet basement. accommodate the three-wire plug, have an electrician install the correct outlet, or use an Do not place the monitor on an un
ページ4に含まれる内容の要旨
For Your Safety EN-5100e Special Notes on LCD Monitors General Notes The following symptoms are normal with an LCD Do not install the monitor near heat sources monitor and do not indicate a problem: such as radiators or air ducts. Due to the nature of the fluorescent light, the Do not place monitor in direct sunlight or in screen may flicker during initial use. Turn off the areas with excessive dust, mechanical vibration Power Switch and then turn it on again to make or shock. sure t
ページ5に含まれる内容の要旨
Before You Operate the Monitor EN-5100e Installing & Removing the Base General Features: Package Contents 38.1cm(15") TFT Color LCD Monitor The box that your monitor was shipped in should have included the following items: Crisp, Clear Display for Windows 1. EN-5100e LCD Monitor 1024 X 768 @ 75Hz (Maximum & 2. Power Cord Recommended Resolution) 3. Windows 95/98/2000/ME INF Driver Disk ® EPA ENERGY STAR Ergonomic Design Space Saving, Compact Case Design EN-5100e 31MY02 5
ページ6に含まれる内容の要旨
Before You Operate the Monitor EN-5100e Connecting the Wires Using the Power Cord Supplied 1. Connect the built-in video cable into the 15-pin Caution: Make sure the power cord is the correct connector on the back of your computer and type that is required in your area. This LCD tighten the two screws. monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC 2. Connect the power cord into your LCD monitor's voltage areas (no user adjustment is required
ページ7に含まれる内容の要旨
Before You Operate the Monitor EN-5100e Connecting the Wires Using An Optional Power Cord (Not Supplied) The power cord supplied with your monitor can Follow these steps: only be connected to a grounded electrical wall 1. Connect the built-in video cable into the 15-pin socket or power strip. connector on the back of your computer and If you wish to connect your monitor to a power tighten the two screws. supply using the power input socket on the back of 2. Connect the power cord into your
ページ8に含まれる内容の要旨
Before You Operate the Monitor EN-5100e Adjusting the Viewing Angle For optimal viewing, adjust the monitor's angle to Do not touch the LCD screen when you your own preference. change the angle. It may cause damage or breakage. Hold the stand firmly when you change the monitor's angle. Be careful to avoid pinching your hand in the swivel base. You can adjust the monitor's angle from -5° to 45°. EN-5100e 31MY02 8
ページ9に含まれる内容の要旨
Operating Instructions EN-5100e Front Panel Buttons Auto: Press this button to automatically set Power Indicator: A green light indicates the H-Position, V-Position, Clock and Focus that the monitor is on. An orange light settings. indicates that the monitor is in Off mode. Brightness: Press this button to adjust the Power: Press this button to turn the picture’s brightness. If the OSD window is monitor on or off. The power indicator will open, this button allows you to move within light up.
ページ10に含まれる内容の要旨
Operating Instructions EN-5100e Adjusting the OSD Settings 1. Press the MENU button to open the OSD 5. To save and exit, highlight the EXIT icon and window. press MENU or leave the monitor alone for 10 seconds. If you want to adjust any other 2. Press the < or > buttons until the desired function, repeat steps 2-4. function is highlighted. Note: When the OSD window is open, the input 3. Press MENU to open the function’s window. signal timing settings appear at the top. 4. Press the < or
ページ11に含まれる内容の要旨
Operating Instructions EN-5100e Plug & Play DDC1/2B Feature How to Install INF & ICM File This monitor is equipped with VESA DDC1/2B 1. Insert the Windows 95/98/2000/ME/XP INF capabilities according to the VESA DDC Driver Disk into your floppy drive. STANDARD. It allows the monitor to inform the 2. Follow the Add New Hardware Wizard host system of its identity and, depending on the instructions on the screen. level of DDC used, communicate additional 3. If the wizard asks for the location o
ページ12に含まれる内容の要旨
Technical Support (FAQ) EN-5100e Problem Possible Solution Power LED is not ON Make sure the power button is ON. Make sure the power cord is properly connected to a grounded power outlet and to the monitor. No Plug & Play Confirm that your computer is Plug & Play compatible. Confirm that your video card is Plug & Play compatible. Inspect the video cable and make sure that none of the pins are bent. Make sure the Envision monitor drivers are installed. (ENVISION monitor drivers are
ページ13に含まれる内容の要旨
Technical Support (FAQ) EN-5100e Problem Possible Solution 1 2 Screen image is not Adjust the CLOCK and FOCUS settings or press the AUTO button to centered or sized automatically re-configure the monitor’s settings. properly Picture has color Adjust the settings for Red, Green and/or Blue colors or select a different defects (white does color temperature: 65 (6500 K) or 78 (7800 K). not look white) Poor brightness or The life time of the back-light is limited. After 20,000 hours, the l
ページ14に含まれる内容の要旨
Technical Support (FAQ) EN-5100e Error Message Possible Solution Input not supported Your computer has been set to an incompatible display mode. Right click on the desktop and choose Properties. Click the Settings tab then set your computer’s display mode to one of the settings listed in the resolution chart below. Unsupported mode Your computer’s resolution is out of VESA specifications. try different video Right click on the desktop and choose Properties. Click the Settings tab then ca
ページ15に含まれる内容の要旨
Appendix EN-5100e Specifications Plug & Play VESA DDC1/ 2BTM LCD Driving TFT Color LCD Panel system Input Connector D-Sub 15-pin Size 15.0" (38.1 cm) Input Video Signal Analog: 0.7 Vpp Pixel pitch 0.01” (0.3 mm) (H) 75 OHM, Positive x 0.01” (0.3 mm) (V) Maximum Screen Size Horizontal: 12.0" (304.1 mm) Viewable 100° (H) 80° (V) Vertical: angle 9.0" (228.1 mm) Input Response 40 milliseconds time Power Source 100~264 VAC, Video Red, Green, Blue 47~63 Hz Analog Interface Separate H/V TTL Environ
ページ16に含まれる内容の要旨
Appendix EN-5100e Optimal Viewing Mode: 1024 x 768 x 75 Hz Specifications (continued) Front Panel Buttons Auto Brightness Contrast Power Switch MENU/ Exit External Functions Contrast Controls: Brightness Focus Clock H-Position V-Position Auto-Center 6500° K 7800° K RGB Color temp. Reset Exit EPA ENERGY Yes STAR® Power Consumption 25 Watts (Maximum) Regulatory UL, CSA, FCC, Compliance TÜV/GS, CE EN-5100e 16 31MY02
ページ17に含まれる内容の要旨
Appendix EN-5100e Factory Preset Timing Table Resolution Horizontal Vertical Standard (in pixels) Frequency Frequency VGA 720 × 400 31.47 kHz 70 Hz 640 × 480 31.47 kHz 60 Hz 640 × 480 35.00 kHz 66.6 Hz 640 × 480 37.50 kHz 75 Hz SVGA 800 × 600 37.879 kHz 60 Hz 800 × 600 46.875 kHz 75 Hz 832 × 624 49.725 kHz 75 Hz XGA 1024 × 768 48.363 kHz 60 Hz 1024 × 768 56.476 kHz 70 Hz 1024 × 768 60.02 kHz 75 Hz 1024 × 768 60.241 kHz 74.9 Hz EN-5100e 17 31MY02
ページ18に含まれる内容の要旨
Appendix EN-5100e Connector Pin Assignment Pin Number Description Pin Number Description 1Red 9+5V 2 Green 10 Detect Cable 3Blue 11 NC 4 Ground 12 DDC-Serial Data 5 Ground 13 H-Sync 6 R-Ground 14 V-Sync 7 G-Ground 15 DDC-Serial Clock 8 B-Ground EN-5100e 18 31MY02
