ページ1に含まれる内容の要旨
PIXMA MG4200
series
Setup Guide
© CANON INC. 2012
ページ2に含まれる内容の要旨
Setup Guide This guide provides information for setting up a network connection for the printer. Network Connection Wireless Connection Preparation for Connection Printer Setup Setup Procedure Selection Push Button Method Standard setup WPS Other setup (Advanced setup) Disable WEP WPA/WPA2 Character Entry Troubleshooting
ページ3に含まれる内容の要旨
Network Connection Wireless Connection a Preparation for Connection Before Starting Wireless Connection Setup 1. Make sure that the printer is turned on. If the power is on, the POWER lamp (A) will be lit. Notes on Wireless Connection • Make sure that the computer is connected to the access point (A) (or wireless network router) you want to connect your printer to. • The confi guration, router functions, setup procedures and security settings of the network device vary depending on your system
ページ4に含まれる内容の要旨
2. Use the or button (A) to display the WLAN setup icon. 3. Press the left Function button (B). The (blue) Wi-Fi lamp (C) lights up when wireless connection is enabled. c Setup Procedure Selection The printer will automatically search for access points supporting WPS (Wi-Fi Protected Setup). * If the Push Button Method screen is displayed on the printer When you are unsure if your access point or router supports this technology, press the Stop button. Proceed to the screen for Standard setup.
ページ5に含まれる内容の要旨
d-A Push Button Method d Connection Using WPS 1. Press and hold the WPS button on the access point. For details on pressing the WPS button, refer to the access point manual. 2. Press the OK button on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer fl ashes while searching for or connecting to the access point. 3. When the left screen appears, press the OK button. The network connection setup is now complete.
ページ6に含まれる内容の要旨
d-B Standard setup d Connection via Standard setup 1. Select Standard setup. 2. Press the OK button. 3. Select your access point, then press the OK button. 4. One of the screens below will be displayed on the printer. 5. Press the OK button. 6. Enter the network password (WEP key or passphrase). Character entry is case-sensitive. 7. Press the left Function button. 8. Make sure that the network password is correct. Character entry is case-sensitive. 9. Press the left Function button. 10. When the
ページ7に含まれる内容の要旨
d-C WPS d Connection Using WPS 1. Select WPS. 2. Press the OK button. 3. Select Push button method. 4. Press the OK button. 5. Press the OK button. 6. Press and hold the WPS button on the access point. For details on pressing the WPS button, refer to the access point manual. 7. Press the OK button on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer fl ashes while searching for or connecting to the access point. 8. When the left screen appears, press the OK button. The network co
ページ8に含まれる内容の要旨
d-D Other setup (Advanced setup) d Connection via Advanced setup 1. Select Other setup. 2. Press the OK button. 3. Select Advanced setup. 4. Press the OK button. 5. Select your access point, then press the OK button. 6. Select the security protocol used by the access point, then press the OK button. Disable 7. When the left screen appears, press the OK button. The network connection setup is now complete.
ページ9に含まれる内容の要旨
WEP 7. Select the WEP key number you want to use. 8. Press the OK button. 9. Press the OK button. 10. Enter the WEP key. Character entry is case-sensitive. 11. Press the left Function button. 12. Make sure that the WEP key is correct. 13. Press the left Function button. 14. When the left screen appears, press the OK button. The network connection setup is now complete.
ページ10に含まれる内容の要旨
WPA/WPA2 7. Press the OK button. 8. Enter the passphrase. Character entry is case-sensitive. 9. Press the left Function button. 10. Make sure that the passphrase is correct. 11. Press the left Function button. 12. When the left screen appears, press the OK button. The network connection setup is now complete.
ページ11に含まれる内容の要旨
Character Entry You can enter the characters when the keyboard is displayed on the printer. Follow the procedure below. 1. You can enter the characters when the keyboard is displayed on the printer's LCD. Password entry is case sensitive so press the center Function button (A) accordingly to switch between lower case, upper case and numeric characters. 2. Use the buttons (B) to select a character from the keyboard, then press the OK button to select and move to the next character. 3. Repea
ページ12に含まれる内容の要旨
Troubleshooting Standard setup The Target Access Point is Not Detected • Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back on. • Check the access point name/network name and network password of your access point or router. • Are the computer and network device confi gured? • Are the access point and printer installed in an open space where wireless communications are possible? • Is the access point operating in IEEE802.1
ページ13に含まれる内容の要旨
When using multiple access points: Select Use multiple AccessPoints, then press the OK button. An Unknown Access Point is Displayed Access points in use nearby may also be detected. The Access Point Name is Not Displayed Properly Access point names with double-byte characters are not displayed properly. However, they can be selected. The Access Point Name is Not Displayed Automatically Refer to the manual supplied with the access point or contact its manufacturer. The Network Password is
ページ14に含まれる内容の要旨
WEP Failed to connect to the access point. Make sure that the WEP key entered for the access point is correct. In addition, when using WEP key number 2, 3 or 4 of the access point, set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly. For details on how to change the WEP key number of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there may
ページ15に含まれる内容の要旨
WPA/WPA2 Failed to connect to the access point. Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the sections below: • If the DHCP function of the access point is inactive, enable the DHCP function and confi gure wireless connection settings again. • For details on how to check or change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer.
ページ16に含まれる内容の要旨
To perform Standard setup again 1. Press the HOME button (A). 2. Use the or button (B) to display WLAN setup, then press the left Function button (C).
ページ17に含まれる内容の要旨
WPS Cannot connect. Connections are being attempted from multiple access points simultaneously. The screen appears when connections are being attempted from multiple access points simultaneously. Wait for a while, then configure WPS settings again. Press the WPS button on only one access point. Failed to connect. The screen appears when an error occurs. Check the access point settings, then configure WPS settings again. For details on how to check the settings of the access point, refer to
ページ18に含まれる内容の要旨
Advanced setup The Target Access Point is Not Detected • Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back on. • Check the access point name/network name and network password of your access point or router. • Are the computer and network device confi gured? • Are the access point and printer installed in an open space where wireless communications are possible? • Is the access point operating in IEEE802.11n (2.4 GHz), IE
ページ19に含まれる内容の要旨
When using multiple access points: Select Use multiple AccessPoints, then press the OK button. An Unknown Access Point is Displayed Access points in use nearby may also be detected. The Access Point Name is Not Displayed Properly Access point names with double-byte characters are not displayed properly. However, they can be selected. The Access Point Name is Not Displayed Automatically Refer to the manual supplied with the access point or contact its manufacturer.
ページ20に含まれる内容の要旨
WEP Failed to connect to the access point. Make sure that the WEP key entered for the access point is correct. In addition, when using WEP key number 2, 3 or 4 of the access point, set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly. For details on how to change the WEP key number of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there may