ページ1に含まれる内容の要旨
EPSON Stylus COLOR 670
edge Media
paper support
guides
Media name Size Part number
printer cover
EPSON 360 dpi Ink Jet Paper Letter S041060
A4 S041059
EPSON High Quality Ink Jet Letter S041111
Paper A4 S041117
control panel
EPSON Photo Quality Ink Jet Letter S041062
output tray
Paper A4 S041161
Legal S041067
EPSON Photo Quality Glossy Letter S041124
Paper A4 S041126
EPSON Photo Quality Glossy Letter S041072
Film A4 S041071
output tray
A6 S041107
extensions
EPSON Photo Paper Letter S041141
A4 S0
ページ2に含まれる内容の要旨
EPSON Stylus COLOR 670 Paper Paper type Size Paper types Thickness Weight Single sheets Letter (8.5 × 11 inches) Plain bond paper and special ink jet 0.003 to 0.004 inch 17 to 24 lb 2 Legal (8.5 × 14 inches) papers distributed by EPSON (0.08 to 0.11 mm) (64 to 90 g/m ) Half letter (statement, 5.5 × 8.5 inches) for plain bond for plain bond Executive (7.5 × 10 inches) paper paper A4 (210 × 297 mm) A5 (148 × 210 mm) Transparencies, glossy Letter (8.5 × 11 inches) Transparencies, glossy paper, a
ページ3に含まれる内容の要旨
EPSON Stylus COLOR 670 . Mechanical A Paper feed Friction method Paper path Sheet feeder, rear entry L & R Sheet feeder 2 capacity 100 sheets of 17 lb (64 g/m ) paper Dimensions Storage Width: 16.9 inches (429 mm) C Depth: 10.3 inches (261 mm) EPSON 4 × 6-inch Photo Paper * Height: 6.6 inches (167 mm) (dotted lines indicate perforations) Printing Width: 16.9 inches (429 mm) A: The maximum top margin is 0.67 inch (17.0 mm). Depth: 24.1 inches (613 mm) L & R: The maximum left and right margin is
ページ4に含まれる内容の要旨
EPSON Stylus COLOR 670 P S B A flash When all the lights flash, your printer may have Control Panel an internal error. Make sure you removed all the packing material as described on the unpacking sheet in your printer box. Then turn off the power light printer, wait a few seconds, and turn it on again. If the lights still flash, contact your dealer or EPSON. paper out light P S B A are off When all the lights are off, the printer is not receiving power. Try t
ページ5に含まれる内容の要旨
EPSON Stylus COLOR 670 2. Lift up the two ink cartridge clamps. Testing the Printer You can run a printer check to determine whether a problem comes from the printer itself or some other source. Follow these steps to run the printer check: 1. Make sure both the printer and computer are turned off. 2. Disconnect the interface cable from the printer. 3. Make sure paper is loaded in the printer. 4. Hold down the E load/eject button, then press and release the Ppower button. Continue hold
ページ6に含まれる内容の要旨
EPSON Stylus COLOR 670 Printing on Special Media Replacing an Ink Cartridge You cannot print if either ink cartridge is empty. Leave Whether you print on plain paper or special media, you need the empty cartridge installed in the printer until you have to select the Media Type setting according to the guidelines in obtained a replacement. Otherwise the ink remaining in the table below. the print head nozzles may dry out. Select this Media Type To ensure good results, use genuine EPSO
ページ7に含まれる内容の要旨
EPSON Stylus COLOR 670 2. Press the R cleaning button and hold it for about three 6. Lower the new ink cartridge into its holder with the label seconds until the print head moves left and the Ppower facing up and toward the back of the printer. Then press light begins flashing. down the ink cartridge clamp until it locks in place, but don’t press down on the cartridge itself. 3. Pull up the ink cartridge clamp. The cartridge rises up from its holder. (The illustration shows color
ページ8に含まれる内容の要旨
EPSON Stylus COLOR 670 3. Pull up the ink cartridge clamp. The cartridge rises up from 6. Lower the new ink cartridge into its holder with the label its holder. (The illustration shows color ink cartridge facing up and toward the back of the printer. Then press replacement. To replace the black ink cartridge, lift up only down the ink cartridge clamp until it locks in place, but the smaller clamp on the left.) don’t press down on the cartridge itself. 7. If you need to replace the other
ページ9に含まれる内容の要旨
EPSON Stylus COLOR 670 Using the Head Cleaning Utility Using the Control Panel Follow these steps to run the Head Cleaning utility Follow these steps to clean the print head: (recommended method): 1. Make sure the printer is turned on but not printing, and 1. Make sure the printer is turned on but not printing, and both the B black and A color ink out lights are off. (If an both the B black and A color ink out lights are off. (If an ink out light is flashing, replace the ink cartri
ページ10に含まれる内容の要旨
EPSON Stylus COLOR 670 4. You see the Utility menu. Click the Print Head Alignment Examining the Nozzle Check Pattern button. Examine the nozzle check pattern you print. It should look 5. Follow the instructions on the screen to print a test page. something like this: 6. Select the most precise alignment pattern from the choices on the test page. Enter the number of the best aligned pattern following the instructions on the screen. Cleaning the Printer Each staggered horizontal and straight
ページ11に含まれる内容の要旨
EPSON Stylus COLOR 670 4. Open the printer cover. Secure the ink cartridge holder to the printer with tape as shown, then close the printer cover. Tape the ink cartridge holder to the printer case 5. Push in the output tray extensions and close the tray. 6. Repack the printer and attachments in the original box using the protective materials that came with it. See the unpacking sheet that was packed with your printer. Be sure to keep the printer level as you transport it. After transporting
