Summary of the content on the page No. 1
MODEL BE MODEL BE-1 -100HT 00HT
MODEL BE MODEL BE--100HT 100HT
HE HE HE HEADS ADS ADS ADSE E E ET T T T TELE TELE TELE TELEP P P PHONE HONE HONE HONE
OWNER’S MAN OWNER’S MAN OWNER’S MAN OWNER’S MANU U U UAL AL AL AL
PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY.
- 1 -
Summary of the content on the page No. 2
- 2 -
Summary of the content on the page No. 3
TABLE OF CONTENTS Introduction ------------------------------------------------------------------- 4 Features and Controls ----------------------------------------------------- 5 Installation --------------------------------------------------------------------- 7 Installing your Headset Telephone -----------------------------------7 Operation ----------------------------------------------------------------------8 Using the Headset ---------------------------------------------------
Summary of the content on the page No. 4
INTRODUCTION Thank you for purchasing the Model BE-100HT Headset Telephone. The BE-100HT is a full featured compact telephone, designed to provide hands-free operation using a comfortable lightweight headset. You will experience a greater level of comfort and convenience with the BE-100HT Headset Telephone than when using a standard telephone handset for communications and at the same time keep your hands free to perform other functions. Features include: • Adjustable microphone bo
Summary of the content on the page No. 5
FEATURES AND CONTROLS Figure 1 1 2 3 4 13 5 6 14 11 12 7 15 8 9 10 1. TELEPHONE LINE JACK Connects incoming telephone line plug from telephone wall jack. 2. RINGER Hl/LOW SWITCH The HI/LOW switch adjusts the sound level of the ringer. 3. TONE/PULSE SWITCH Selects either TONE or PULSE dialing. 4. IN-USE LED The IN-USE LED indicates when phone is off hook. 5. DIALING KEY PAD The dialing keys are used to dial outgoing calls. 6. VOLUME CONTROL Adjusts incoming voice sound level.
Summary of the content on the page No. 6
FEATURES AND CONTROLS - continued Figure 2 BELT CLIP TELEPHONE An optional belt clip is supplied with your BE-100HT headset telephone. It can be easily installed or removed as required. See Figure 2 1.Insert the belt clip mounting tabs into the corresponding mounting holes located on the rear surface of the BE-100HT. 2. Confirm the belt clip mounting tabs are aligned correctly. 3. Press the belt clip towards the right side of the BE-100HT to lock
Summary of the content on the page No. 7
INSTALLATION INSTALLING YOUR HEADSET TELEPHONE The BE-100HT is a complete telephone and can be used in the same manner as any single line telephone. See Figure 3 1. Insert the plug from the headset cord into the modular jack marked HEADSET on the left side of the BE-100HT. 2. Plug one end of the supplied telephone line cord into the modular jack marked LINE on the top side of the BE-100HT. 3. Plug the remaining end of the modular telephone line cord into any existing RJ-11C mod
Summary of the content on the page No. 8
OPERATION USING THE HEADSET The BE-100HT is supplied with a high quality microphone to provide clear voice communications. The boom microphone can be swiveled to position so the headset can be used on either ear. See Figure 4 1. Place the headband over Figure 4 your head with the speaker on the ear of your preference. Stablizer T-Bar 2. With one hand grasp and hold the ear cushion. Carefully pull the boom Cushioned Speaker microphone down and into position so that the Micropho
Summary of the content on the page No. 9
OPERATION - continued 6. Always leave enough slack in the cord so that you can move your head freely. MAKING OUTGOING CALLS 1. Put on the headset and adjust it for your comfort. 2. Adjust boom microphone so that it is about the width of two fingers from your mouth. 3. Push the TALK button (7), you will hear a dial tone in your headset speaker and the IN USE LED will light. 4. Adjust the VOLUME control to set the dial tone volume to a comfortable sound level. 5. Using th
Summary of the content on the page No. 10
OPERATION - continued 3. When you hear an incoming call ringing, push the BE-100HT TALK button (7). The BE-100HT telephone will answer the call and the IN USE LED will light. 4. Begin speaking normally into the microphone. 5. After completing your conversation, push the TALK button (7) to hang up and disconnect the call. The IN USE LED will go out. ADJUSTING THE RINGER VOLUME The volume of the telephone ringer can be adjusted by moving the ringer switch (2) on the back of t
Summary of the content on the page No. 11
OPERATION - continued 1. The redial function will dial numbers up to a maximum of 32 digits. FLASH BUTTON The FLASH button (9) when pressed will create a quick break on the telephone line. 1. The flash button can be used if you have call waiting service to switch between calls (consult your local telephone company for this service). 2. The flash button feature can also be used when the BE-100HT is connected to compatible PBX system (consult your PBX system manual). HO
Summary of the content on the page No. 12
CARE AND MAINTENANCE Your BE-100HT telephone has been designed to provide years of trouble free service. It is a sensitive electro-mechanical instrument. To assure its longevity, please read the following maintenance instructions. • Keep the BE-100HT telephone away from heat as high temperatures can shorten the life of the electrical components and distort or melt its plastic parts. • The unit should be kept free of dust and moisture. If it gets wet, wipe it dry immediately. Liquids
Summary of the content on the page No. 13
FCC INFORMATION This equipment complies with Part 68 of the FCC Rules. On the bottom or back of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. Upon request, you must provide this information to your telephone company. The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your telephone number is call
Summary of the content on the page No. 14
IMPORTANT SAFETY INFORMATION When using your telephone, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and/or injury to persons including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Do not use liquid cleaners, or aerosol cleaners. Use a damp cloth for cleaning. If necessary, use a mild soap. 4. Do not use this product near water, for example near a bath tub,
