Summary of the content on the page No. 1
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury to persons, including
the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for exa
Summary of the content on the page No. 2
Important Safety Instructions 12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions: A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, because improper
Summary of the content on the page No. 3
Introduction The QW2432 is an advanced cordless telephone that operates in the 2.4GHz frequency range. Your QW2432 is capable of supporting up to a maximum of 4 Handsets. Using additional Handsets, up to three people can be conferenced on a call (2 Handsets and the Base Speakerphone), or two extensions can be conferenced on a call, while two other extensions can be talking internally, using the Intercom feature. This manual is designed to familiarize you with the QW2432 cordless telephone. To o
Summary of the content on the page No. 4
OWNER’S MANUAL Parts Check List 5. Battery Pack 1. Base Unit 6. Wall Mounting Bracket 2. Handset 7. Belt Clip 3. AC Power Adapter 8. Owner's Manual 4. Telephone Cord 4
Summary of the content on the page No. 5
The Handset Layout 1. Antenna 9. LCD Display 2. Message Waiting Indicator 10. Select 3. Earpiece 11. Off (Clear) 4. Headset Jack (2.5mm) 12. Battery Compartment 5. Scroll Keys 13. Intercom 6. On (Flash) 14. Services Key 7. Dialing Key (0-9) 15. Microphone 8. Handsfree Speakerphone 4 5
Summary of the content on the page No. 6
The Base Unit Layout Phone Cord Jack AC Power Jack Message Waiting Indicator Page/Intercom Key In Use Indicator Power Indicator Charge Indicator Mute Key Volume Keys Dialing Keys (0-9) Hold Key Flash Key Redial Key Messages Key 3-Way Calling Key Cancel Call Waiting Key Speakerphone Key Charging Contacts 6
Summary of the content on the page No. 7
Setup Plug the AC power adapter into an electrical outlet, and the DC connector into the back of the base unit. To AC outlet To telephone socket outlet AC adapter To telephone jack Connecting to phone line Plug one end of the telephone line cord into the jack on the back of the base unit. Plug the other end of this cord into the wall jack. Checking for dial tone After the battery is charged press ON on the Handset. The Phone icon will appear on the handset display, and you will hear dial ton
Summary of the content on the page No. 8
Installation of Battery Pack in Handset Follow the steps below: 1. Remove the battery cover by pressing on the indent and sliding downward. 2. Place the new battery pack in the handset with the metal contacts aligned with the charge contacts in the battery compartment. 3. Replace the battery cover by sliding it upwards. 4. If the new battery pack is not already charged, place the handset in the base unit, or a remote charging stand, and allow it to charge for 12 hours. After initial charge,
Summary of the content on the page No. 9
Spare Battery Charger/Power Backup Function The QW2432 can use a the spare battery in the Base Unit to provide operational backup in the event of a power failure. With a fully charged battery pack in the spare battery charger, you will still be able to place and receive calls from the Handset for up to 5 hours. The spare battery pack can also be used to replace a drained handset battery, ensuring uninterrupted use. A spare battery can be purchased from most retail stores that carry electronic eq
Summary of the content on the page No. 10
Charging Of Handset Battery Pack The Handset of your QW2432 cordless telephone is powered by a rechargeable battery pack. It charges automatically whenever the Handset is in the Base Unit. You should charge the battery pack for 12 hours when you first receive your phone. You'll know the battery pack needs charging when: The low battery message is displayed : The handset seems completely dead, the LCD is completely clear and does not activate when you press the keys. CAUTION: TO REDUCE THE RI
Summary of the content on the page No. 11
Wall Mounting The Wall Mount bracket is designed for use on standard Wall Mount plates only. 1. Line up the tabs on the wall mount adapter with the holes on the back of the base unit. Snap the wall mount bracket firmly in place. 2. Plug the AC adapter into an electrical outlet, and the DC connector to the back of the base unit. If the handset battery pack has not been charged previously, place the handset in the base unit cradle, and allow it to charge for 12 hours. 3. Connect the telephone
Summary of the content on the page No. 12
Registration and Operation Registration and Operation of the QW2422 Accessory Handset Your QW2432 system can operate up to 4 Handsets. The accessory Handset consists of the following: Setup of the QW2422 Accessory Handset 1. Plug the AC power adapter into an electrical outlet. 2. Remove the Handset battery cover by pressing on the indent and sliding downward. 3. Place the new battery pack in the Handset, with the metal contacts aligned with the charge contacts in the battery compartment. 4.
Summary of the content on the page No. 13
Registration and Operation Enter Base ID Code 1. After charging the Handset, remove it from its Charge Cradle, the screen will display: 2. Press NEW, then enter the 15 digit Base Unit ID code, located on the underside of the Base Unit. 3. Press OK. The Handset will display: PLEASE WAIT!! 4. Wait approximately 15 seconds. The Handset will display: FOUND BASE V14 If the Handset displays: BASE BUSY TRY LATER, this indicates that the system is in use. Wait until the Base Unit is in the idle (on h
Summary of the content on the page No. 14
Handset and Base Indicators Handset Icons Icon Description Line In Use indicator On steady with no number next to it when a parallel set is in use. On steady with one or more numbers next to it, indicating which extensions are using the line. For example, 12 indicates that Handset 1 and Handset 2 are on an outside call. Intercom indicator On steady with the extension numbers currently on an intercom call. For example, 02 indicates that the Base and Handset 2 are on an intercom call. B
Summary of the content on the page No. 15
Handset and Base Indicators Handset LEDs Description LED Flashes to indicate that you have new messages in your Message voicemail. Service must be subscribed to through your local Waiting telephone company. Base LEDS Description LED Flashes to indicate that you have new messages in your Message voicemail. Service must be subscribed to through your local Waiting telephone company Lights when base unit is receiving power from wall outlet Power Flashes when unit is in Power Backup mode. L
Summary of the content on the page No. 16
Soft Menu Functions The QW2432 has an advanced design that uses a menu structure and soft keys to access all of the built-in features. Example of the idle mode display: RDL (Redial) Press RDL to display the last 5 telephone numbers dialed. The number on top line is the most recent number dialed. Use the scroll keys to select the desired number. To dial the number, you can simply press the ON or HANDSFREE key. MENU With the Handset in the idle (OFF) mode, press the MENU key to access the
Summary of the content on the page No. 17
Calls Log (Caller ID) From the idle (OFF) mode, press MENU, use the scroll keys to select CALLS LOG, then press OK. The Caller ID information of the most recently received call will be displayed. To scroll to other records, use the scroll keys. To dial the number displayed, you can simply press the ON or HANDSFREE key. You can also press the CID key to access the following options ( DEL, OPT#, SAVE): DEL : Select this option to delete THIS or ALL records in Caller ID memory. OPT# : Select th
Summary of the content on the page No. 18
Handset Settings From the Handset Settings menu you can select the following options to modify: RINGER VOLUME Select this option to adjust the ringer volume. Use the scroll keys to adjust the volume up or down. A Handset will display a graphic indicator of the selected volume setting. Press OK to confirm your selection and return to the Handset Settings menu. RINGER MELODY Select this option to adjust the ringer melody or tone. Use the scroll keys to select from the six availab
Summary of the content on the page No. 19
Range Extender Your QW2432 has an enhanced feature that is designed to improve performance. If you are using your QW2432 in an area with excessive interference, or you require a moder- ate increase in operating range. the Range Extender feature can help to improve both the sound quality and range. Actual range will depend on your environment. To select the Range Extender setting, follow the procedure listed below: In the idle(OFF) mode, press MENU and use the scroll keys to select RANGE EXTEND
Summary of the content on the page No. 20
MEM (Memory) The QW2432 can store up to 50 names/numbers in memory. Each memory location can hold up to 32 digits and up to 16 characters for the name. When prompted to ENTER NAME, use the digit keys to 'spell' the name. Each press of a particular key causes characters to be displayed in the following order: Number Key Characters (in order) 1 & ' , . 1 2 A B C a b c 2 3 D E F d e f 3 4 G H I g h i 4 5 J K L j k l 5 6 M N O m n o 6 7 P Q R S p q r s 7 8 T U V t u v 8 9 W X Y Z w x y z 9 0 0 *
