Summary of the content on the page No. 1
TM
TM
14AF41
3J70201B COVER 1 28/5/01, 2:23 PM
Using the TV’s Setting up Using the Connecting Important Welcome to
Appendix
Features your TV Remote Control your TV Safeguards Toshiba
Summary of the content on the page No. 2
Welcome to Toshiba Congratulations! You have purchased one of the finest color TVs on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible. Please make sure you’ve received the following items: TV, remote control, batteries, manual, registration card, and extended service plan literature. If you did not receive all of the items, or any of the items are damaged or broken, please contact your Toshiba dealer. In addition, you ma
Summary of the content on the page No. 3
Important Safeguards ......................................................................................................... 2 Connecting your TV ............................................................................................................ 4 Connecting a VCR .......................................................................................................................................4 Connecting a cable converter box ......................................................
Summary of the content on the page No. 4
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER The exclamation point within an equilateral triangle is (OR BACK). NO USER-SERVICEABLE intended to alert the user to the presence of important PARTS INSIDE. REFER SERVICING
Summary of the content on the page No. 5
13. LIGHTNING To protect your unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges. 14. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines, or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing
Summary of the content on the page No. 6
Connecting your TV If you haven’t connected electronic equipment before, or you have been frustrated in the past, you may wish to read this section. (Cables are not supplied.) • A coaxial cable is the standard cable that comes in from your antenna or cable converter box. Coaxial cables use “F” connectors. • Audio and video cables are usually color coded according to use: yellow for video and red and white for audio. The red audio cable is for the stereo right channel, and the white audio cable i
Summary of the content on the page No. 7
Connecting a cable converter box This television has an extended tuning range and can tune most cable channels without using a cable company supplied converter box. Some cable companies offer "premium pay channels" in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company. For Subscribers to Basic Cable TV Service For basic cable service not requiring a Converter/Descrambler box, conne
Summary of the content on the page No. 8
Connecting a DVD/satellite receiver and a VCR You will need: This connection allows you to watch DVD/satellite, video and TV • one coaxial cable programs. You can record from the DVD/satellite receiver and TV, as • two pairs of audio cables (only one cable well as record one TV channel while watching another channel. for a mono VCR) To satellite • one video cables DVD / Satellite Receiver • one S-video cable OUT L Satellite IN Caution: R You can use a video cable instead of the AUDIO S-video cab
Summary of the content on the page No. 9
Connecting two VCRs This connection allows you to record from one VCR to another VCR You will need: while watching a video program. You will also be able to record from • one coaxial cable one TV channel while watching another channel. • two pairs of audio cables (only two cables for mono VCRs) Stereo VCR / Playback • two video cables To antenna IN IN from ANT OUT to TV Caution: OUT Do not connect one VCR to the output and CH 3 LR CH 4 VIDEO AUDIO input jacks on the TV at the same time. If you a
Summary of the content on the page No. 10
Using the remote control Preparing the remote control for use With the remote control, you can operate your TV, most VCR models, Note: and cable TV converters together, even if they are different brands. If This remote control’s functions may or may you will be using your TV with a Toshiba VCR, your remote control is not operate your VCR or cable TV converter. already programmed and ready to use. If you own different brands of Refer to the owner’s manuals supplied with VCRs and/or converters, yo
Summary of the content on the page No. 11
Programming the remote control for use with a VCR or a cable TV converter This remote control is pre-programmed to operate Toshiba VCRs. To use VCRs or cable converters other than Toshiba models, you must follow the steps below before you operate your remote control. Note: 1. Press the CODE button and the VCR or the CABLE button you • When shipped from the factory, the remote want to register at the same time. control is set to operate your TV. 2. Enter the 2-digit code listed below using the Di
Summary of the content on the page No. 12
Learning about the remote control POWER turns the TV on and off (page 8) Sleep timer sets the TV to go off at a set time (page 21) TV/Video selects video input source (page 21) Channel + / – cycles through programmed channels (page 12) TV/VCR/Cable POWER TV VCR CABLE TV/VCR/Cable switches between TV, VCR and Cable (page 9) POWER CH RTN 12 3 Channel Numbers allow direct access to channels (page 12) ENT Channel Return Channel Volume + / – adjusts the volume level 45 6 100 Numbers Channel Return re
Summary of the content on the page No. 13
Setting up your TV After you’ve installed the batteries and programmed the remote control, you need to set some preferences on the TV using the menu. You can access the menu with the buttons on the remote control. • When you make a menu selection, your changes occur immedi- ately. You do not have to press MENU or EXIT to see your changes. • After fifteen seconds, the menu screen will automatically disappear if you do not make a selection. Your changes will still be saved. • When you are finished
Summary of the content on the page No. 14
Adding channels to the TV’s memory Your TV will stop on specific channels that are stored in the TV’s channel memory when you press Channel + or –. Use the steps below to set all active channels in your area automatically. Programming channels automatically Your TV can automatically detect all active channels and store them in its memory. After the TV has stored the channels in its memory, you can erase channels or add your favorite channels. To add channels: POWER TV VCR CABLE 1. Press MENU, th
Summary of the content on the page No. 15
Using the TV’s features POWER TV VCR CABLE CH RTN Adjusting the channel settings 12 3 Channel ENT Return Switching between two channels 45 6 100 You can switch between two channels without entering an actual Channel 0 Numbers channel number each time. 78 9 CH + To switch between two channels: VOL VOL 1. Select the first channel you want to view. – + MENU/ 2. Select a second channel with the Channel Number buttons (0-9, ENTER 100). 3. Press CH RTN. The previous channel will be displayed. – CH Ea
Summary of the content on the page No. 16
To clear your favorite channels: POWER 1. Select a channel you want to clear. TV VCR CABLE 2. Press MENU, then press or to display the OPTION menu. CH RTN 3. Press or to highlight FAVORITE CH. 12 3 4. Press or to display the FAVORITE CH menu. SET/CLEAR will 45 6 0 be highlighted. Channel 78 9 0 Numbers + CH CH PICTURE AUDIO SET UP OPTION VOL VOL – + MENU/ FAVORITE CH : CH 12 ENTER SET/CLEAR SET CLEAR Menu/ SET UP CH 736 4 1 Enter 12 125 63 40 TV CABLE 13 28 97 112 CH – SELECT SET ENTER
Summary of the content on the page No. 17
3. Press to or display the V-CHIP menu. CH PICTURE AUDIO SET UP OPTION V-CHIP Note: BLOCKING RESET If you forget your PIN code, press RECALL PIN CODE four times within five seconds from the V-CHIP SELECT [0-9] SET ENTER menu. This allows you to proceed to the END EXIT BLOCKING menu and reset your PIN code. 4. Use the Channel Number buttons (0-9) to enter your PIN code. If you are accessing the V-Chip menus for the first time, select a four-digit number to be your PIN code. Press ENTER. The BLO
Summary of the content on the page No. 18
MPAA Ratings X For adults only. NC17 Not intended for anyone 17 or under. R Restricted. Under 17 requires an accompanying parent or adult guardian. PG13 Parents strongly cautioned. Some material may be inappropriate for children under 13. PG Parental guidance suggested. Some material may not be appropriate for children. G General audience. Appropriate for all ages. Youth TV Ratings Y7, Y7 FV Directed to older children. This program is designed for children age 7 and above. For those programs whe
Summary of the content on the page No. 19
To use the V-Chip to block programs by rating: 1. Press MENU, then press or to display the OPTION menu. POWER TV VCR CABLE 2. Press or to highlight V-CHIP. CH RTN 3. Press or to display the V-CHIP menu. 12 3 4. Use the Channel Number buttons (0-9) to enter your PIN code. If you are accessing the V-Chip menus for the first time, select a 45 6 0 four-digit number to be your PIN code. Press ENTER. Channel 78 9 0 Numbers The BLOCKING menu appears. + CH VOL VOL – + CH MENU/ ENTER PICTURE AUD
Summary of the content on the page No. 20
Blocking unrated movies or programs Some movies and programs are not rated. You can block these movies and programs using the V-Chip. To block unrated movies or programs: 1. Press MENU, then press or to display the OPTION menu. 2. Press or to highlight V-CHIP. 3. Press or to display the V-CHIP menu. 4. Use the Channel Number buttons (0-9) to enter your PIN code. If you are accessing the V-Chip menus for the first time, select a four-digit number to be your PIN code. Press ENTER. The BLOC
