Canon Digital Camera user manual

User manual for the device Canon Digital Camera

Device: Canon Digital Camera
Size: 0,30 MB
Date of adding : 2014-11-23 15:14:12
Number of pages: 9
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Canon Digital Camera. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Canon Digital Camera.

For your convenience

If looking through the Canon Digital Camera user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manualCanon Digital Camera on full screen, use the buttonFullscreen.
  • Downloading to your computer - You can also download the user manual Canon Digital Camera to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Canon Digital Camera user manual
Advertisement
« Page 1 of 9 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Canon Digital Camera but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Canon Digital Camera. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

How To hardwire the CANON SURE SHOT OWL PF DATE 35mm CAMERA

Revised 1/12/04

This document outlines the modification of the Canon Sure
Shot Owl PF Date Camera so the shutter controls can be
operated remotely. It is recommended that the following “three
wire” setup be used in all cameras modified, and alternate “2
wire” setups are converted outside the camera.
Please note that following these modifications will void the
camera’s warranty. No guarantee is implied or expressed in
these

Summary of the content on the page No. 2

Remove screw inside camera enclosure #2 Remove Viewfinder Shroud, Battery Door, and Shutter Button Assembly Remove viewfinder shroud by prying shroud Viewfinder shroud removed from away from camera body at the top corner. camera body. Remove shutter button assembly. Remove battery door.

Summary of the content on the page No. 3

#3 Remove the Camera Body from the Camera Cover Remove the camera body from the camera cover by prying the body from the battery compartment. The camera body can be removed completely from the camera cover. The camera body removed from the camera cover. Camera body / cover.

Summary of the content on the page No. 4

#4 Modify Wire Route and Attach Wiring Harness Locate camera body side with strap guide. Notch the strap guide for the wire route. Insert wires through lower hole in camera cover, and hot glue “free” end into strap guide slot.

Summary of the content on the page No. 5

#5 Wiring the Camera Wire the camera with the following positions. One wire is soldered to the pad that connects to pin 6, (counted from right to left) on the top pc board of the camera. This is the refresh wire. One wire is soldered to the pad that connects to pin 5, (counted from right to left) on the top pc board of the camera. This is the shutter wire. The last wire is soldered to the spot indicated on the front pc board of the camera body. This is the common wire.

Summary of the content on the page No. 6

Better picture of solder pad 4 (common) #6 Reassemble Camera Body and Cover Slide camera body into camera cover inserting right side of camera body first. Press camera body into camera cover, until the door latch hits edge of camera body.

Summary of the content on the page No. 7

Pry camera cover over door latch and slide camera body back into camera cover. Check fit at bottom of camera cover. Check fit on top of camera cover Check wiring harness to make sure wires are not located directly under top screw hole.

Summary of the content on the page No. 8

#7 Reinstall Shutter Button Assembly, Battery Door, and Viewfinder Shroud. Reinstall shutter button assembly, battery door, and viewfinder shroud that were removed in step #2. #8 Reinstall Screws Reinstall screws, starting with the longest screws at the strap guide holes. Squeeze camera body and camera cover together for these screws only. Finish screw reinstall for remaining screws.

Summary of the content on the page No. 9

#9 Finish Hardwired Camera and Testing Complete wired camera with “three wire” setup, showing servo three wire connector. To test camera, refresh wire #6 and shutter wire #5 are solder together. Camera will fire flash when these two wires are touched to common wire #4. Camera must be on, and back door must be latched. “Film” winding will be heard after the first test. Subsequent test will not include winding without film in the camera. A 6 second delay is needed between tests f


Similar user manuals
# User manual Category Download
1 Canon 17 Digital Camera 18
2 Canon 110ED20 Digital Camera 37
3 Canon 1100HS Digital Camera 34
4 Canon 1000 Digital Camera 24
5 Canon 1N RS Digital Camera 49