Summary of the content on the page No. 1
USA
DS602 (Prefinished)
DS602I (Integrated)
Models DS602 DS602I
Part No. 599066/D
Summary of the content on the page No. 2
Single DishDrawer Table of Contents Section 1 General Information 1.1 Preparation 1.2 Product Specifications & Cavity Dimensions 1.3 Options for Installing Multiple Products 1.4 Electrical, Plumbing & Drainage Information 1.5 Product Parts 1.6 Additional Product Parts for Integrated DishDrawer Section 2 Fitting the DishDrawer 2.1 DishDrawer Mounting Hole Locations 2.2 Connecting the Services 2.3 Flexible Extrusion Attachment for 24 Cavity Section 3 Inserting DishDrawer Into Cavity Section 4 I
Summary of the content on the page No. 3
GENERAL INFORMATION SECTION 1 STEP 1.1 PREPARATION NOTE TO THE INSTALLER n Be sure to leave these instructions with the Customer. n Ensure this appliance is properly grounded. WARNING NOTE TO THE CONSUMER Before installing the n Keep these Installation Instructions with your Use & Care Manual for future reference. DishDrawer, remove the IMPORTANT house fuse or open the n Read these Instructions completely and carefully. circuit breaker. n Observe all governing Codes and Ordinances. WARNING E
Summary of the content on the page No. 4
STEP 1.3 OPTIONS FOR INSTALLING MULTIPLE PRODUCTS IMPORTANT Where the DishDrawer is in an under counter situation, i.e. built into a kitchen unit, it is recommended that bare wood surrounding the DishDrawer is sealed with an oil based paint or polyurethane to prevent possible steam damage. IMPORTANT If mounting the DishDrawer near the bottom of the cabinet, ensure there is adequate STEP 1.4 ELECTRICAL, PLUMBING & DRAINAGE INFORMATION room underneath the supporting cabinet to ELECTRICAL tighten
Summary of the content on the page No. 5
PLUMBING - DRAINAGE OPTIONS WARNING Option 1 Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a Option 2 qualified electrician. WARNING The Drain Hose Support 3 must be at least 13 /4" (350mm) above th
Summary of the content on the page No. 6
Tools Needed To STEP 1.5 PRODUCT PARTS Install DishDrawer 1. Wooden Chopping Board 2. Level Safety Glasses Utility Knife Pencil Drill & Drill Bits 3. 3 9 11 ( /32", /16" & /32") (2.5mm, 12mm, 14mm) Sandpaper Tape Measure Square Ruler 6. 5. Phillips Screwdriver Pliers 4. 7. Adjustable Wrenches(x2) 7 /32" (6mm) Allen Key (Integrated Models) Router (Integrated Models) Jigsaw (Integrated Models) 9. 8. 11. 12. 10. 1. Template (Single 1) 7. Single Connector (1) 8. Edg
Summary of the content on the page No. 7
FITTING THE DISHDRAWER SECTION 2 STEP 2.1 DISHDRAWER MOUNTING HOLE LOCATIONS 2.1.1 Draw the cavity center line on the TIP supporting cabinetry. Ensure the cavity is at 7 least 22 / " (580mm) deep. 8 2.1.2 Center Template in cavity using V-notch on the front of the Template. IMPORTANT For Integrated product with door thickness other 3 than /4 (18mm), the Template position must be adjusted forward or back to allow for this difference. 2.1.3 Align front of Template to suit surround of cabinetry.
Summary of the content on the page No. 8
STEP 2.2 CONNECTING THE SERVICES WARNING Ensure the edges of the 2.2.1 Service Hole are smooth Feed the Power Cord, Inlet Hose and Drain Hose through the Services Hole. Position or covered. (See Step 1.2 - the DishDrawer in front of the opening. Product Specifications & Cavity Dimensions.) If the Services Hole is through a metal partition, the hole 2.2.2 must be protected with the Connect the Inlet Hose to the HOT WATER Edge Protector provided. SUPPLY. Ensure the sealing washer supplied with
Summary of the content on the page No. 9
2.2.6 WARNING If required, trim the Single Connector to the size which matches the waste tee or air The Product MUST NOT break to be used. There are ribs provided to guide cutting. be plugged in at this stage. When using the Single Connector, the hose should be pushed in firmly, 5 clicks. Remember to slip the Wire Clip over the Drain Hose before connecting to the Single Connector. The supplied Wire Clip should be installed between the two positioning ribs on the Single Connector. 2.2.7 Attach S
Summary of the content on the page No. 10
STEP 2.3 FLEXIBLE EXTRUSION ATTACHMENT FOR TIP 24 (610mm) CAVITY Wiring, Plumbing and 2.3.1 Services should be completed before Flexible Extrusions are supplied to enable the installer to help fill any excess space attaching the flexible between the sides of the DishDrawer and extrusion. the cavity. The two lengths of Flexible Extrusion (supplied) should be attached before pushing the DishDrawer into the cavity for final installation. This Extrusion is designed to fit a 24 (610mm) width cav
Summary of the content on the page No. 11
INSERTING DISHDRAWER INTO CAVITY SECTION 3 WARNING 3.1.1 Position product to suit joinery ensuring DO NOT push against hoses are not kinked or cut. the middle of the drawer. IMPORTANT Make sure the inlet and drain hose and main flex are not restricted or damaged by carefully pulling them through the Services Hole as the DishDrawer is being pushed back into the cavity. 3.1.2 Insert M8 bolts and washers through holes in shelf. WARNING The DishDrawer should not support any part of the kitchen cab
Summary of the content on the page No. 12
INFORMATION FOR CABINET MAKER FOR SECTION 4 INTEGRATED DISHDRAWER STEP 4.1 INTEGRATED DRAWER FRONT DIMENSIONS I 4.1.1 IMPORTANT Use the following diagrams to work out the dimensions for the Integrated Panels for Drawer Fronts. N Recommended Drawer Front thickness for T Integrated product is 5 3 /8" to /4" (16mm - 18mm). E G IMPORTANT R Drawer Front material A must be suitable for damp conditions or adequately sealed to withstand T moisture. E Additional protection can be provided by using a
Summary of the content on the page No. 13
IMPORTANT I A minimum clearance of 3 /32 (2.5mm) must be N maintained between the Drawer Front and existing T cabinetry, except between the underside of the Drawer Front and the E 1 shelf, where a /4 (6mm) clearance is needed for G product venting. R A T E Drawer Front Air Flow Chamfer D Chamfer the back of the Drawer Front Panel at the bottom as shown, to enhance air flow. P R O D U 4.1.2 Use the following diagrams if installing the DishDrawer at floor level. C T O N L Y Page DS_12
Summary of the content on the page No. 14
4.1.3 IMPORTANT I Control Badge Position All marking out to be Badge can be located anywhere within the Mounting Zone shown. Handle position will need to be taken into account. done on the back surface N of the Drawer Front. T E G R A T IMPORTANT E When mounting the handle, ensure fastenings do not protrude beyond D the back surface of the Drawer Front. P R O IMPORTANT 4.1.4 Accuracy is essential D Badge Cutout Dimensions when cutting the Badge Cut out Badge Mounting Hole in the chosen position
Summary of the content on the page No. 15
4.1.5 I Drawer Front Mounting Bracket Nut Holes 11 Using a / (8.5mm) diameter drill bit, drill out the four screw holes in each door 32 9 panel to a depth of /16 (14mm). Remove burrs. N T E WARNING G Use of a depth gauge is recommended when drilling out holes for R Drawer Front Mounting Panel. A T E CAUTION D 1 * These dimensions are important to ensure a / (6mm) airflow gap. 4 Ensure the drill does not damage the face of the Drawer Front. P R O D U C T O N L Y Page DS_14
Summary of the content on the page No. 16
SECTION 5 INTEGRATED DRAWER FRONT INSTALLATION STEP 5.1 CHANGING THE INTEGRATED BADGE ENCLOSURE I There are several different colored Integrated badges to choose from. They IMPORTANT include black, chrome, satin & brass. Two color options are provided with your machine, other options are available from your local Dealer. N To avoid electric shocks and damage to electronic There are five parts to the 5. components, the Integrated Badge Assembly. T They are as follows: integrated badge shou
Summary of the content on the page No. 17
STEP 5.4 FITTING THE BADGE, HANDLE & MOUNTING WARNING PANEL TO THE DRAWER FRONT I Care should be taken in the following steps. 5.4.1 N Remove Drawer Front Mounting Panel by withdrawing pins from sides of drawers T using long nosed pliers. CAUTION E Take care not to damage front surface of panel. 5.4.2 G Slide Mounting Panel off in a downwards Ensure all cuts are and outwards motion. straight and care is taken R to avoid damage to the Drawer Front. A T E 5.4.3 D Using an Allen Key, screw
Summary of the content on the page No. 18
STEP 5.5 FITTING THE DRAWER FRONT TO THE DISHDRAWER TIP I Use a small amount of 5.5.1 liquid soap along the lip N Fit seal to Drawer. of the seal to aid the Drawer Front to slide on T easily against the seal. E CAUTION G The rubber seal between the Drawer and Drawer R Front must be kept in place. A T WARNING E The Electronics Board is an electrostatic sensitive 5.5.2 device. Ensure you are D Plug the grounding wire into the panel. adequately grounded when connecting or Connect badge wires to
Summary of the content on the page No. 19
FINAL FITTING FOR SINGLE DISHDRAWER SECTION 6 6.1.1 Check final fit of DishDrawer in cavity. 6.1.2 Tighten M8 bolts. Page DS_18
Summary of the content on the page No. 20
SECTION 7 FINAL CHECKS SECTION 12 STEP 7.1 INSTALLATION WET TEST 1. Ensure product is level, securely fastened to the floor and opens and closes freely. Ensure inlet hose to faucet connection is tightened to specification. 2. 3. Ensure any knockouts or plugs in the drain connection have been drilled out and the drain connection made correctly. 4. Plug in and turn ON the power and water supply. The DishDrawer should "beep" and light up. 5. Open the drawers of the DishDrawer and check operatio
