Summary of the content on the page No. 1
INSTRUCTION MANUAL
DISHWASHER
Summary of the content on the page No. 2
Contents 1. Safety and operating instructions __________________________ 38 2. Installation and hook-up__________________________________ 41 3. Description of the controls ________________________________ 45 4. Operating instructions ___________________________________ 54 5. Cleaning and maintenance _______________________________ 63 6. Troubleshooting ________________________________________ 67 Thank you for choosing this product. We advise you to carefully read all the instructions contained
Summary of the content on the page No. 3
Safety instructions 1. Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE EEC DIRECTIVES 72/23, 89/336 (INCLUDING 92/31 AND 93/68) CURRE
Summary of the content on the page No. 4
Safety instructions THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE 2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE). BY ENSURING THIS PRODUCT IS DISPOSED OF CORRECTLY, YOU WILL HELP PREVENT POTENTIAL NEGATIVE CONSEQUENCES FOR THE ENVIRONMENT AND HUMAN HEALTH, WHICH COULD OTHERWISE BE CAUSED BY INAPPROPRIATE WASTE HANDLING OF THIS PRODUCT. THE SYMBOL ON THE PRODUCT, OR ON THE DOCUMENTS ACCOMPANYING THE PRODUCT, INDICATES THAT THIS APPLIANCE MAY NOT BE TREATED
Summary of the content on the page No. 5
Safety instructions DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE. KNIVES AND OTHER SHARP-POINTED KITCHEN UTENSILS MUST BE PLACED IN THE CUTLERY BASKET WITH THEIR TIPS FACING DOWNWARD. AQUASTOP MODELS THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A WATER LEAK. WHEN THE AQUASTOP DEVICE IS TRIPPED, CALL IN A QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT. IN MODELS EQUIPPE
Summary of the content on the page No. 6
Installation instructions 2. Installation and hook-up Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, an
Summary of the content on the page No. 7
Installation instructions 2.1 Water supply connection Preventing the risk of clogging or damage: if the water pipe is new or has not been used for a long time, before connecting to the water supply check that the water is clear and free of impurities, to prevent damage to the appliance. The dishwasher must always be connected to the water system with new hoses; old or used hoses must never be reused. CONNECTING TO THE WATER SUPPLY Connect the intake hose to a cold water supply with ¾” gas
Summary of the content on the page No. 8
Installation instructions IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD: IT IS NECESSARY TO INSTALL IN THE FIXED WIRING AN ALL-POLE DISCONNECTION DEVICE HAVING A GAP BETWEEN CONTACTS OF AT LEAST 3.5MM. AFTER INSTALLATION THE DISCONNECTION DEVICE HAS TO BE EASY TO REACH. THE CONNECTION TO THE MAINS MUST BE CARRIED OUT BY A QUALIFIED TECHNICIAN IN ACCORDANCE TO THE SCHEME SHOWN BELOW AND THE REGULATIONS IN FORCE. L = brown N = blue = yellow-green In the event of damage to
Summary of the content on the page No. 9
Installation instructions FOR UK ONLY: THIS APPLIANCE MUST BE EARTHED. Fuse replacement If the mains lead of this appliance is fitted with a BS 1363A 13amp fused plug, to change a fuse in this type of plug use an A.S.T.A. approved fuse to BS 1362 type and proceed as follows: 1. Remove the fuse cover A and fuse B. 2. Fit replacement 13A fuse into fuse cover. 3. Refit both into plug. The fuse cover must be refitted when changing a fuse and if the fuse cover is lost the plug must not be
Summary of the content on the page No. 10
User instructions 3. Description of the controls 3.1 Upper panel All the dishwasher controls are grouped on the upper panel. Switch-on, programming, switch-off etc. procedures are only possible when the door is open. ON/OFF BUTTON 1 Pressing this button energises the appliance. SELECTED PROGRAM INDICATOR LIGHTS 2 Illumination of this light denotes the program selected and the occurrence of a fault (troubleshooting). PROGRAM SELECTION BUTTON 3 By pressing this button in sequence it is p
Summary of the content on the page No. 11
User instructions "3/1" OPTION BUTTON 8 Press this button to activate the option for use of 3/1 products. "3/1" OPTION LIGHT 9 Illuminates to indicate that the function is activated. WASH-ZONE BUTTON 10 Press this button to select the zone where you wish to concentrate the washing action. WASH-ZONE LIGHTS 11 If one of the lights is on, the wash-zone washing system has been selected. PROGRAM DELAY BUTTON 12 Press this button to delay the start of the program by up to 9 hours. INFORMAT
Summary of the content on the page No. 12
User instructions SETTING THE WASHING PROGRAM AND SWITCHING ON To select the most suitable program for the dishes to be washed refer to the table below, which indicates the most appropriate program according to dish type and degree of soiling. After using the table to identify the most appropriate washing program: press the ON/OFF button (1) and wait for the PROGRAM INDICATOR LIGHT (2) to illuminate; keep pressing the PROGRAM SELECTION button (3) until the indicator light correspondin
Summary of the content on the page No. 13
User instructions PROGRAMME CONSUMPTION (3) DURATION TYPE OF PROGRAM DETERGENT MINUTES WATER POWER DISHES DESCRIPTION GRAMS NR SYMBOL NAME (2) (LITRES) (KWh) AND DIRT (1) (2) Clean mixed dishes requiring Cold rinse DISH rinsing and Rinse at 68°C 40' 3,5 0,70 - 6 WARMER warming before Dry taking to table Wash at 45°C Crystal, porcelain Cold rinse CRYSTAL 7 and mixed dishes, 70' 10 0,90 20 Rinse at 68°C light dirt Dry Cold prewash Extended wash at Mixed dishes, B
Summary of the content on the page No. 14
User instructions The washing cycle will not take place if the dishwasher door is left open or not properly closed. TABLE FOR CERTIFICATION BODIES Reference standard EN 50242 Reference program BIO Load 12 place-settings Type of detergent B Amount of detergent 30 g Rinse aid setting 5/6 3.2 Washing programs Before starting a washing program make sure that: The water supply tap is open. The correct amount of detergent has been added to the dispenser. The baskets have been correctly l
Summary of the content on the page No. 15
User instructions CHANGING THE PROGRAM To change the program in progress, simply open the door and select a new program. When the door is closed the dishwasher will automatically select the new program. SELECTING THE WASH-ZONE OPTION (available in all programs except the soak program) Press button (10) in repetition to select the zone where you wish to concentrate the washing action, in the following order: 1) right zone 65% - left zone 35% (right-hand light on); 2) right zone 35% - lef
Summary of the content on the page No. 16
User instructions "3/1" OPTION BUTTON (available in all programs except the soak program) By pressing the button (8) you activate the "3/1" option, confirmed when the relative light comes on. This option has been studied for the use of dishwashing powder or tablets with integrated substances in place of regenerating salt or rinse-aid known on the market as “3 in 1” or “triple action” products; in this case the dishwasher will use the product in an optimal way avoiding salt and rinse-ai
Summary of the content on the page No. 17
User instructions ADJUSTING THE WATER SOFTENING SYSTEM N.B.: for the setting below to be possible, a washing program other than the soak program must be set. Press the PROGRAM DELAY button (12) and keep it pressed until the preset value appears followed by a full stop (normally 3.). Release the button then press it again in succession to display the value required, referring to the table. The 6 setting levels available will appear in this order: 3., 4., 5., 0., 1., 2.. When the value requ
Summary of the content on the page No. 18
User instructions If the door has to be opened while washing is in progress, the program will be interrupted. The relative light will keep flashing and a beeper will signal that the cycle has not been completed. When the door is closed the program will continue from where it was interrupted. This operation should only be carried out if strictly necessary, because it might cause problems in execution of the program. END OF CYCLE At the end of the program the beeper sounds briefly and the
Summary of the content on the page No. 19
User instructions 4. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: Adjust the water softening system; Add the regenerating salt; Add the rinse aid and detergent. 4.1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic softening system which uses a spec
Summary of the content on the page No. 20
User instructions Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. When necessary, refill the regenerating salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion. Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damag
