Summary of the content on the page No. 1
7500AI
Digital Telephone Answering Machine
with Caller ID
Operating Guide
for Australia and New Zealand
Summary of the content on the page No. 2
CONTENTS CONTENTS Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Parts Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation Selecting a Location . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting the 7500AI to the Telephone Line . . . . . . . 6 Connecting Power . . .
Summary of the content on the page No. 3
CONTENTS Continued over.... Recording Incoming Messages . . . . . . . . . . . . . . . . . 17 Display Information During Incoming Calls . . . . . . . 18 Screening Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Recording A Memo . . . . . . . . . . . . . . . . . . . . . . . . . 20 Two-Way Recording . . . . . . . . . . . . . . . . . . . . . . . . 21 Call Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Calls and Messages Display . . . . . . . . . . . . . .
Summary of the content on the page No. 4
SAFETY INFORMATION FOR YOUR SAFETY, PLEASE OBSERVE THE FOLLOWING:- • Never install telephone wiring during lightning storm. • Do not use your 7500AI unit near water or when wet. • Do not take apart or remove the screws (except battery cover screw) - there are no serviceable parts inside. • Make sure the line cord and AC Adaptor do not cause a trip hazard. READ THIS BEFORE INSTALLATION Your 7500AI conforms to Australian or New Zealand Telecommunications Authority Standards and you can connect it
Summary of the content on the page No. 5
SAFETY INFORMATION NOTE: NEW ZEALAND ONLY The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to it’s network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it impl
Summary of the content on the page No. 6
INTRODUCTION Congratulations on the purchase of your 7500AI Digital Telephone Answering Machine (7500AI) with Caller ID Display. This product has been designed especially for the Australian or New Zealand market. It is guaranteed to provide you with reliability, long life and outstanding performance. The 7500AI is built with a wide screen for easy viewing of caller identification. It displays the caller’s details (name* and telephone number) the time and date the call came through, and an indic
Summary of the content on the page No. 7
PARTS CHECKLIST If any of these items are missing or damaged, please contact the place of purchase. 7500AI Telephone cord and Telephone cord and or Splitter for New Zealand Splitter for Australia AC Adaptor 9 Volt Battery Operating guide 4 9 volt
Summary of the content on the page No. 8
FEATURES YOUR 7500AI’S FEATURES INCLUDE:- ➤ Wide Screen ➤ Pause Message Playback ➤ 88 Caller ID Memories ➤ New Message Review ➤ 12 VIP Call Alert ➤ Voice Time & Day Stamp ➤ Up to 18 minutes ➤ Call & Message Counter Record Time ➤ Call Timer ➤ 2 Outgoing Messages (OGM) ➤ Adjustable Ring Tone (2/4/7) ➤ Time & Date Display ➤ Toll Saver ➤ Two-Way Recording ➤ Room Monitor ➤ Memo Recording ➤ Remote Access ➤ Call Screening ➤ Call Breakthrough ➤ Callback Feature ➤ Memory Backup ➤ New Calls & (9V Battery
Summary of the content on the page No. 9
INSTALLATION SELECTING A LOCATION Select a location that is near both a telephone socket and an AC outlet. CONNECTING THE 7500AI TO THE TELEPHONE LINE To connect the 7500AI to the phone line, plug one end of the supplied modular cord into the jack on the back of the 7500AI labelled “line”. Then plug the cord’s other end into a telephone socket. If you wish to connect both the 7500AI and a telephone to the telephone line, simply use the two way splitter supplied. Plug the splitter into the te
Summary of the content on the page No. 10
INSTALLATION INSTALLATION CONNECTING POWER Use only the Uniden AC Adaptor supplied with this Uniden 7500AI Digital Telephone Answering Machine. 1. Plug the AC Adaptor into the power socket at the rear of the 7500AI labelled “AC 9V 400mA”. 2. Then plug the other end into your mains socket. When the power is first connected, the CALL# AM NEW 7500AI beeps and the display shows a OGM1 OGM2 memory test counting from 00 to 22. MEMORY TEST After the counter reaches 22, the 7500AI CALL# AM N
Summary of the content on the page No. 11
INSTALLATION BACKUP BATTERY If the power fails or you unplug the 7500AI, a 9V backup battery would save the messages and the settings for the day, time and security code. We recommend you use an alkaline battery. Disconnect the telephone line and power line cords before replacing the battery. Always use a new 9V battery for optimum performance. Follow these steps to install the backup battery. 1. Use a Phillips screwdriver to remove the screw on the compartment cover. 2. Push down the latch t
Summary of the content on the page No. 12
CONTROLS & FUNCTIONS 18 17 16 1 15 2 14 13 12 3 4 5 11 9 6 10 8 7 1. Speaker 10. Stop Button 2. LCD Screen 11. Message Play Button 3. Ring Selector 12. Outgoing Message 2 Button 4. Answer On/Off & 13. Outgoing Message 1 Button New Message LED Indicator 14. Memo Button 5. Volume Control Switch 15. New Call LED Indicator 6. Answer On/Off Button 16. Callback Button 7. Message Skip Button 17. Message Delete Button 8. Message Repeat Button 18. VIP Select Button 9. Microphone 9
Summary of the content on the page No. 13
CONTROLS & FUNCTIONS 2 3 4 5 6 7 CALL# AM NEW 8 1 OGM1 OGM2 ANS ON 9 10 UNIDEN 1. VIP Alert ON Indicator 6. Answer ON/Announce Only Indicator 2. No/Low Battery Indicator 7. Message Indicator 3. Time 8. New Call/MSG/Call Counter 4. OGM1 & OGM2 Indicator 9. Caller’s Telephone Number 5. Date 10. Caller’s Name* *Caller’s name will appear only if it is sent by Telstra or your telephone service provider. 10
Summary of the content on the page No. 14
SETTING UP NOTE: If you do not complete each step within 8 secs., the 7500AI will exit set-up mode and return to standby. In this case you have to start again by pressing STOP for 2 secs. LCD CONTRAST The 7500AI provides 0 to 9 (lightest to darkest) levels LCD luminescence. 1. Press STOP for 2 secs. The 7500AI beeps to confirm entry to set-up mode. 2. Press REPEAT to adjust contrast CALL# AM NEW to desired level. OGM1 OGM2 3. Press CALLBACK to save setting and continue setting up. LCD CONTRA
Summary of the content on the page No. 15
SETTING UP 3. Press REPEAT to select desired CALL# AM NEW number and SKIP to move up to the OGM1 OGM2 next digit. 4. Press CALLBACK to save set-up SET CBT CODE and continue to next set-up. TIME AND DATE NOTE: If you have subscribed to a caller ID service, time and date will be updated automatically during the first call. 1. Press STOP for 2 secs. CALL# AM NEW OGM1 OGM2 2. Press CALLBACK 3 times. 3. Press REPEAT to set AM or PM (the SUNDAY hour, minutes, day and month). 4
Summary of the content on the page No. 16
SETTING UP SETTING UP NUMBER OF RINGS The 7500AI can be set to 2, 4 or 7 rings before it plays the OGM and receives the call. To set the ringer, move the ringer select switch to the desired position. TS (TOLL SAVER) The 7500AI has New Message Detection to avoid unnecessary toll charges when calling long distance to check your messages. To use this feature set the ringer select to TS. If there are new messages, the 7500AI will answer after 2 rings, otherwise it will answer after 4 rings. Thus, wh
Summary of the content on the page No. 17
NEW MESSAGE NEW MESSAGE ANSWER ANSWER VIP ANSWER SKIP REVIEW VIP ANSWER SKIP REVIEW MEMO REPEAT MEMO REPEAT DELETE DELETE OGM2 STOP OGM2 STOP - CALLER ID - CALLER ID OGM1 OGM1 PLAY PLAY CALLBACK CALLBACK SYSTEM SYSTEM NEW CALL NEW CALL ANSWERING ANSWERING DIGITAL DIGITAL SETTING UP RECORDING OUTGOING MESSAGES NOTE: The maximum length for OGM 1 and OGM 2 is 60 seconds each. The display counts the recording time. 1. Press and hold OGM1 or OGM2 for 2 secs or until a beep is heard. 2. Speak in
Summary of the content on the page No. 18
SETTING UP NEW MESSAGE NEW MESSAGE ANSWER ANSWER VIP ANSWER SKIP REVIEW VIP ANSWER SKIP REVIEW MEMO REPEAT MEMO REPEAT DELETE DELETE OGM2 STOP OGM2 STOP - CALLER ID - CALLER ID OGM1 OGM1 PLAY PLAY CALLBACK CALLBACK SYSTEM SYSTEM NEW CALL NEW CALL ANSWERING ANSWERING DIGITAL DIGITAL SETTING UP NOTE: • If no outgoing OGM1 is recorded when you press OGM 1, the 7500AI announces "You have no announcement one" and sounds four beeps. • If no outgoing OGM2 is recorded when you press OGM 2, the 7500AI
Summary of the content on the page No. 19
NEW MESSAGE ANSWER VIP ANSWER SKIP REVIEW MEMO REPEAT DELETE OGM2 STOP - CALLER ID OGM1 PLAY CALLBACK SYSTEM NEW CALL ANSWERING DIGITAL BASIC OPERATION SETTING THE 7500AI TO ANSWER CALLS To Turn the 7500AI On To set the 7500AI to answer calls and record messages, press ANSWER once. The 7500AI announces "Answer-on", beeps once and plays the outgoing message. The Answer LED indicator lights up. ANS ON appears on the display. The 7500AI is now set to answer calls using the OGM 1 message and recor
Summary of the content on the page No. 20
BASIC OPERATION BASIC OPERATION RECORDING INCOMING MESSAGES The maximum incoming message recording length is 60 seconds. When a recording reaches 55 seconds, the 7500AI beeps once to notify the caller that time will soon be up. When the recording reaches 60 seconds, the 7500AI sounds one long and four short beeps, and plays "Thank you for your call", then hangs up. While the incoming call is being recorded the display shows: The 7500AI hangs up and resets to CALL# NEW PM answer the
