Summary of the content on the page No. 1
DISHWASHER
ZSF 2420
822 61 11-16
Summary of the content on the page No. 2
Contents For the Installer For the user Technical Specifications 15 Safety Information 3 Unpacking 16 Description of the appliance 4-5 - Spray arm - Damages - Use - Coarse strainer/microfilter - Positioning - Fine filter - Detergent dispenser Installation 17-18 - Rinse aid dispenser - Water inlet - Water softener - Water drainage The control panel 6 - Power supply - How to set the delayed start Information for test centres 19 Adjusting the water softener 7 Programme chart 8 Loading and unloading 9
Summary of the content on the page No. 3
Safety information Before installing and first using the dishwasher, read this instruction booklet carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and sa
Summary of the content on the page No. 4
Description of the appliance 4 5 - 4 -
Summary of the content on the page No. 5
3. Wipe off any spillage carefully to prevent excessive Spray arm (1) foaming during the next wash programme. It is important to keep all the holes in the spray arm clear. A clogged hole can seriously affect washing efficiency. 4. Close the lid and press until it locks again. If the spray arm needs cleaning, unscrew the nut anti- clockwise, remove the washer and lift off the spray arm. Do not fill the rinse aid dispenser with liquid Clear the holes and shake out any food remnants. detergent. Zan
Summary of the content on the page No. 6
The control panel Indicator and Reset position control lamps On/Off Indicator lamp Programme Delay start selector button Start/Cancel button Programme selector Indicator lamps: Turn the programme selector clockwise or anticlockwise Shows current phase of the selected programme. to select the programme and temperature according to • Wash cycle in progress top lamp the programme chart. • Drying in progress middle lamp Start/Cancel button • Programme cycle lowest lamp In addition to starting a pr
Summary of the content on the page No. 7
Adjusting the water softener To prevent limescaling on the dishes and to the interior of the Contact your local Water Authority to find the dishwasher, the dishes must be washed with soft water. exact water hardness level for your area. This dishwasher is equipped with a water softener, where tap- The water softener has 10 settings: water which is harder than 4 °d (german degree) is softened. Adjust the water softener according to the table below for the water hardness level for your area. Sett
Summary of the content on the page No. 8
Programme chart All types of Coffee cups, All types of Type of Plates and dishes dishes cooking pots dishes delicate items • heavily Type of • normally • normally • lightly • 3) soiled soil: soiled soiled soiled • dried-on food • dried-on food remnants remnants especially egg- white and starch Suitable programme: INTENSIVE NORMAL ENERGY SAVE QUICK PRERINSE 2) 70° C 65° C 55° C 50° C - Programme Pre-wash Pre-wash Pre-wash - Prerinse Washing Washing Washing Washing - cycle: 2 x rinses Rinse Rin
Summary of the content on the page No. 9
Loading and unloading the dishwasher How to load the dishes Baskets The illustration shows the dishwasher loaded with six Main basket place settings. Your own dishes are not likely to be Cutlery basket identical to this load, but if you follow the advice below The cup shelves can be placed in two different we are sure you will be pleased with the results. levels. l Always place glasses, cups and bowls upside down. l Incline deep dishes (soup plates etc.) so that the water can run off when dryi
Summary of the content on the page No. 10
Using the appliance Starting the programme Cancelling the drying phase 1. Scrape or rinse off solid food remnants. In case you do not want to wait until the drying phase is completed, you can cancel it. 2. Load the dishwasher. (See the basket and loading). 1. Press and hold in the start button until the programme indicator lamps starts to flash, 3. Put the correct amount of detergent into the then release the button. detergent dispenser and close the dispenser lid. 2. Open the door. The dryi
Summary of the content on the page No. 11
Maintenance and cleaning General cleaning Moving the dishwasher Inspect the filters and spray arm nozzle before re-loading If you have to move the dishwasher (you are moving the dishwasher and remove any food scraps. Wipe round house, etc): the rubber gasket at the bottom of the door to remove 1. Unplug it. grease which tends to collect there. 2. Turn off the water tap. Cleaning the filters 3. Remove the water inlet and discharge hoses. There are two filters, a coarse one and a fine one which Avoid
Summary of the content on the page No. 12
Something Not Working Before calling out an engineer, please check through the details below because some faults can be rectified easily without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee. Fault Check • Is the door closed properly? The programme will not start. • Have you pressed the start button? • Is the water tap tur
Summary of the content on the page No. 13
If the indicator lamp for the ended programme cycle is flashing, it is possible that you can solve the problem yourself. When the problem is solved, press in the start button and the programme continues. If the problem occurs again, contact your local service centre. Fault Check • Is the water tap turned on? The indicator lamp for the ended • Is the filter inside the inlet hose blocked? programme cycle flashes with approx • Is the water inlet hose kinked or nipped? 3 second pause in between. • Are
Summary of the content on the page No. 14
Guarantee Conditions Standard guarantee conditions We, Zanussi Electrolux, undertake that if within 12 months from the date of the purchase this ZANUSSI ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: • The appliance has been correctly installed and used only on the electricity supply stated on the rating plate
Summary of the content on the page No. 15
Installation instructions Any electrical work required to install this appliance, should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance, should be carried out by a qualified plumber or competent person. Technical specifications Capacity: 6 place settings accordance EN 50242 Dimensions: Height 447 mm Width 546 mm Depth (to the edge of the door) 480 mm Depth (to the middel of the door) 507 mm Weight: Net 22 kg Water pressures: Minim
Summary of the content on the page No. 16
Unpacking Damages If the dishwasher has been damaged during transport, you should immediately notify the company responsible for delivering it. If you discover any damage, faults or that anything is missing, you should notify your retailer immediately. Never leave packaging material in a place where children may play with it. Risk of suffocation! Check that the following accessories are supplied with the dishwasher when you unpack it: – A funnel for filling salt (1) 2 1 – Elbow for discharge hose
Summary of the content on the page No. 17
Installation Water inlet The dishwasher is equipped with safety features which are to prevent the water from going back to the fresh water system. These features are ac- cording to current water technical safety regulations. The dishwasher should be permanently plumbed into a separate cold water supply. The water pressure must be within the limits given in the technical specifications, as it will not function correctly if pressure is outside these specifications. Your local Water Authority will
Summary of the content on the page No. 18
Power supply The dishwasher is supplied with a lead and electrical plug for connection to a 230 V, 13 A earthed wall socket. Before any work is carried out on the dishwasher, it must be isolated from the electric mains supply, for example by removing the plug from the wall socket. Permanent electrical installation must be carried out by an authorised electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not b
Summary of the content on the page No. 19
Information for test centres The salt container and rinse aid dispenser shall be filled in accordance with this instruction manual. Before conducting the measurements the dishwasher shall be operated for one or two complete cycles using detergent and a clean load. Test standard: EN 50242 and EN 60704 Rated capacity: 6 place settings accordance EN 50242 Loading of basket: loading according to figure below Test program: energy saving 55° C Detergent (IEC type B): 9 gram in the dispenser + 5 gram in
Summary of the content on the page No. 20
© Electrolux plc 2005 Technical changes possible
