Summary of the content on the page No. 1
INSTRUCTION MANUAL
GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
Summary of the content on the page No. 2
Contents 1. Description of the controls_________________________________ 12 1.1 Front panel ________________________________________________________________ 12 1.2 Washing programs __________________________________________________________ 15 2. Troubleshooting ________________________________________ 18 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your di
Summary of the content on the page No. 3
User instructions 1. Description of the controls 1.1 Front panel All the dishwasher control are grouped on the front panel. 1 ON/OFF BUTTON 2 SELECTION PROGRAMS BUTTONS (P1...P5) 3 DELAY PROGRAM BUTTON (on some models only) 4 START/PAUSE BUTTON 5 POWER ON LIGHT 6 PROGRAMS LIGHTS 7 DELAY PROGRAM LIGHTS (on some models only) 8 PROGRAM PHASES LIGHTS 9 NO SALT LIGHT (on some models only) 10 NO RINSE AID LIGHT (on some models only) 11 RECESSED DOOR HANDLE LIGHTING When the ON/OFF button (1) is presse
Summary of the content on the page No. 4
User instructions SELECTION PROGRAM The program selection is possible through the relative buttons (2). When the button relating to the program required (see enclosed programs chart) is pressed, the relative light will come on to confirm the operation. PROGRESS PROGRAM PROGRAM SELECTION TYPE AND GRADE DIRT PREWASH WASH COLD RINSE HOT RINSE DRY PANS AND DISHES IN WAITING _ _ _ _ SOAK COLD OF COMPLETING THE LOAD DISHES NOT MUCH DIRTY _ _ QUICK AND WITH "FRESH DIRT" 38°C 1 58°C WITHOUT RESIDUAL DRY
Summary of the content on the page No. 5
User instructions TABLE FOR CERTIFICATION BODIES Reference standard EN 50242 Reference program (*) ECO program Load 9 place-settings Type of detergent B Amount of detergent 30 g Rinse aid setting Depending on the model 3/4 or 4/6 START PROGRAM To start the dishwasher, press the START/PAUSE button (4) for a few seconds, until the light of the first phase of the selected program starts to flash (confirmation beep). As the program runs, the PHASES/PROGRAM lights (8) will indicate the current cycle
Summary of the content on the page No. 6
User instructions TO CHANGE A PROGRAM To change the running program it is necessary: • to interrupt the running program (see “INTERRUPTION OF A PROGRAM”); • select the new program; START/PAUSE (4) • to press again the button to make start the new program. ANNULLING A PROGRAM To annul the program in progress, it must first be interrupted (see “INTERRUPTION OF A PROGRAM”). Now press buttons P1+P2 simultaneously and the first three program lights will come on. In case that the door is opened durin
Summary of the content on the page No. 7
User instructions To set the delay once the program has started, proceed as follows. If the program you wish to carry out is the same as the one already in progress: • press the START/PAUSE button (4) for a few seconds, until the PROGRAM PHASES lights (8) come on; • annul the program in progress (see relative section) and wait for the cycle to come to an end; • select the program again; • select the delay required; • press the START/PAUSE button (4) to start the new program. If the program you w
Summary of the content on the page No. 8
User instructions ADJUSTING THE WATER SOFTENING SYSTEM The dishwasher is equipped with an device for the user to adjust the water softening system according to the hardness of the water supply. The setting switch is inside the plastic locking ring located on the right-hand side, inside the dishwasher. WATER HARDNESS TABLE WATER HARDNESS SETTING German Degrees (°dH) French Degrees (°dF) 0 - 4 0 - 7 Setting N. 1 NO SALT 5 - 15 8 - 25 Setting N. 1 16 - 23 26 - 40 Setting N. 2 24 - 31 41 - 60 Settin
Summary of the content on the page No. 9
User instructions 2. Troubleshooting In case of a malfunction, the dishwasher will identify the program by switching on a combination of lights. When an alrm is present, all the PROGRAM lights (6) come on, while the PROGRAM PHASES lights (8) identify the error code: CODE PHASES LIGHTS DESCRIPTION The anti-flooding system (if installed) has been tripped. E1 The system which limits the water level inside the dishwasher (safety E2 unit) has been tripped. The appliance cannot heat the water. E3 E4 T
Summary of the content on the page No. 10
INSTRUCTION MANUAL WARNINGS AND RECOMMENDATIONS, GUIDE FOR THE USE OF BASKETS WARNINGS AND RECOMMENDATIONS, GUIDE FOR THE USE OF BASKETS AND FOR CLEANING DISHWASHERS AND FOR CLEANING DISHWASHERS
Summary of the content on the page No. 11
Contents 1. Safety and operating instructions __________________________26 2. Installation and hook-up _________________________________29 3. Operating instructions ___________________________________31 4. Cleaning and maintenance _______________________________42 Thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions for the proper, safe use of your dishwasher. The individual sections are lai
Summary of the content on the page No. 12
Safety instructions 1. Safety and operating instructions THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE USING THE APPLIANCE, CAREFULLY READ ALL THE INSTRUCTIONS CONTAINED IN THIS MANUAL. INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR DOMESTIC USE, AND COMPLIES WITH THE EEC DIRECTIVES 72/23, 897336 (INCLUDING 92/31) CURRENTLY IN FORCE, INC
Summary of the content on the page No. 13
Safety instructions • AFTER INSTALLATION, THE PLUG MUST REMAIN ACCESSIBLE. • IN THE EVENT OF DAMAGE TO THE POWER CORD, HAVE IT REPLACED BY A QUALIFIED TECHNICIAN. • AFTER CHANGING THE POWER CORD, MAKE SURE THAT THE BRACKET WHICH SECURES THE CORD IS FIXED SECURELY IN PLACE. IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR, ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT OBSTRUCTED. ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO AVOID WASTING ELECTRICITY. OBSOLETE APPLIANCES MUST
Summary of the content on the page No. 14
Safety instructions LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN MAY CAUSE THE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK. DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM AND BEFORE THE DRYING CYCLE. KNIVES OR OTHER SHARP-ENDED COOKING UTENSILS MUST BE PLACED IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN THE TOP BASKET. TAKE CARE NOT TO CUT YOURSELF AND ENSURE THAT THEY DO NOT PROJECT FROM THE BASKET. AQUAS
Summary of the content on the page No. 15
Installation instructions 2. Installation and hook-up Remove the polystyrene basket retainers. Position the appliance in the desired place of installation. The back or sides of the dishwasher may be placed up against walls or other furniture units. If the dishwasher is installed near a heat source, fit the special insulating panel to prevent overheating and malfunction of the appliance. To ensure stability, install integrated or built-under dishwashers only under continuous worktops, and screw t
Summary of the content on the page No. 16
Installation instructions CONNECTING TO THE WATER SUPPLY Connect the intake hose to a cold water supply with ¾” A gas thread, inserting the filter supplied with the dishwasher. Take care to screw the hose firmly into place with your hands and then complete by tightening about ¼ of a turn with pliers. In dishwashers equipped with the ACQUASTOP device, the filters is already fitted inside the threaded ring. The dishwasher can also be connected to a hot water supply not exceeding 60°C. Supplying t
Summary of the content on the page No. 17
User instructions 3. Operating instructions Once the dishwasher has been correctly installed, prepare for use as follows: • Adjust the water softening system; • Add the regenerating salt; • Add the rinse aid and detergent. 3.1 Using the water softening system The amount of scale contained in the water (water hardness index) can cause whitish staining on the dry dishes, which tend to become dull over time. The dishwasher is equipped with an automatic SALT softening system which uses a special re
Summary of the content on the page No. 18
User instructions • Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. • When necessary, refill the regenerating salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion. Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damage the
Summary of the content on the page No. 19
User instructions ADDING THE RINSE AID The rinse aid helps the dishes dry faster and prevents the formation of scale deposits and staining; it is automatically added to the water during the final rinse cycle, from the container situated on the inner side of the door. To add rinse aid: • Open the door. • Rotate the container cap anticlockwise by ¼ of a turn and remove it. • Add the rinse aid until the container is full (approximately 140 cc). The optical level indicator on the side of the cap sho
Summary of the content on the page No. 20
User instructions ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. Add the detergent and close the cap carefully. During the washing cycle, the dispenser will be opened automatically. • When a SUPER program is selected, in addition to the normal dose of detergent, it is necessary to add an additional amount inside compartment G or H. • Use only detergents specially formulated for dishwashers. For optimal washing results it is important to use a good quality d
