Summary of the content on the page No. 1
DVD-S2500
DVD-S2500_G-cv.fm Page 1 Friday, October 22, 2004 1:56 PM
G
DVD AUDIO/VIDEO SA-CD PLAYER
LECTEUR DE DVD AUDIO/VIDEO SA-CD
DVD-S2500
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
© 2004 All rights reserved.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO
Summary of the content on the page No. 2
Important Note DK SF Advarsel: Luokan 1 laserlaite + Klass 1 laserapparat Laserrudstråling ved åbning når sikkerhesafbrydere er ude Varoitus! af funktion. Undgå u tsættelse for stråling. Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän Bemærk: turvallisuusluokan 1 ylittävälle lasersäleilille. Netafbryderen STANDBY/ON er sekundært indkoblet og afbryder ikke strømmen fra nette. Den indbyggede netdel er Huom. derfor tilsluttet til lysnettet så l
Summary of the content on the page No. 3
General information CAUTION The unit is not disconnected from the AC power source as long Use of controls or adjustments or performance of procedures as it is connected to the wall outlet,even if this unit itself is other than those specified herein may result in hazardous turned off.This state is called the standby mode.In this state,this radiation exposure. unit is designed to consume a very small quantity of power. ATTENTION L ’appareil n ’est pas isolé de la source d ’alimentation aussi
Summary of the content on the page No. 4
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT 1 To assure the finest performance, please read this 17 Before moving this unit, press STANDBY/ON to set manual carefully. Keep it in a safe place for future the unit in standby mode, then disconnect the AC reference. power plug from the wall outlet. 2 Install this sound system in a well ventilated, cool, dry, 18 Place this unit on a flat, hard and stable surface. clean place — away from direct sunlight, heat sources, 19 There must be sufficient ro
Summary of the content on the page No. 5
English Table of Contents DVD features.................................................................21 Introduction 2 Menu............................................................................... 21 Patent information............................................................2 Camera angle.................................................................. 21 Changing the audio language and format....................... 21 Playable disc formats ...........................................
Summary of the content on the page No. 6
Introduction Thank you for purchasing the YAMAHA DVD This manual refers to disc types using the following AUDIO/VIDEO SA-CD player. This Owner’s Manual symbols: explains its basic operations. *1 DVD-Audio DVD-Video Video CD DVD-V VCD DVD-A Patent information Manufactured under license from SA-CD Dolby Laboratories. Audio CD MP3 (Super Audio CD) “Dolby”, “Pro Logic”, and the SA-CD CD MP3 double-D symbol are trademarks of Dolby Laboratories. VCD *1 icon includes Super Video CD. “DTS” and “DTS
Summary of the content on the page No. 7
English Introduction Region management Installing batteries in the information remote control The unit is designed to support the Region Management Insert the batteries in the correct direction by aligning System. Check the regional code number on the disc the “+” and “–” marks on the batteries with the polarity package. If the number does not match the unit’s region markings “+” and “–” inside the battery compartment. number (see table below, or see back of unit), the unit may be unable to
Summary of the content on the page No. 8
30 Introduction Using the remote control Remote control sensor Point the remote control at the sensor, within approximately 6 m (20 feet) of the unit. Handling the remote control Do not spill water or other liquids on the remote control. Do not drop the remote control. Do not leave or store the remote control in the following types of conditions: – high humidity such as near a bath – high temperature such as near a heater or stove – extremely low temperature – dusty places Maintenanc
Summary of the content on the page No. 9
English Functional Overview Front panel STANDBY/ON – turns on this unit or sets it to the standby mode s STOP Disc tray – stops playback b e PAUSE – pauses playback – moves to the previous chapter or track a h PLAY – moves to the next chapter or track – starts playback Front panel display DVD-AUDIO indicator – shows information about the – lights up when the unit detects DVD-Audio operational status of the unit signals SA-CD indicator PROGRESSIVE indicator – lights up when the unit detects SA
Summary of the content on the page No. 10
Functional Overview Rear panel HDMI output terminal – connect to the HDMI jack on a HDMI-compatible AV component SCAN MODE switch – switches the component video output signals between progressive and AC IN (Main-inlet) interlace – connect to a standard AC outlet COMPONENT video jacks i.LINK connectors – connect to an AV receiver with Y PB – connect to the i.LINK jack on an PR inputs i.LINK-compatible component COAXIAL digital audio output OPTICAL digital audio output jack – connect to the au
Summary of the content on the page No. 11
English Functional Overview Remote control DIMMER – adjusts the display brightness AUDIO DIRECT – switches video output on and off during audio disc playback – turns the power of this unit ON or SOUND MODE enters standby mode – selects the required sound mode for SA-CD: CD, Stereo, or Multi- channel (if available) 0-9 numeric buttons for DVD/VCD: Stereo, Dolby Surround compatible, 3D sound, or SUBTITLE Multi-channel – selects subtitle languages PAGE AUDIO – turns pages of the DVD-Audio
Summary of the content on the page No. 12
Preparation There are various ways to connect the player, depending i.LINK components connections on the equipment you wish to use. The following drawings illustrate some possible configurations. Use an i.LINK connection cable of approximately Please refer to manuals for other equipment as necessary 3m (10 feet) or less to connect this unit to i.LINK- to ensure that you make the correct connections. compatible components (refer to page 18 for details). Do not connect the player via your
Summary of the content on the page No. 13
English Preparation Analog audio (MIXED 2CH) connection Use the audio cable supplied with the player to connect AUDIO OUT L (left) and R (right) jacks of the player to the corresponding input jacks on your audio equipment, such as an AV receiver. YPB/CB PR/CR VIDEO S VIDEO COMPONENT IN IN IN AV receiver S VIDEO OUT AV receiver DVD/CD PB/CB PR/CR Y R L VIDEO OUT COMPONENT OUT S VIDEO VIDEO IN IN Video connections COMPONENT IN If your AV receiver features video output jacks, connect PR/CR TV
Summary of the content on the page No. 14
Preparation SCAN MODE selector This selector switches the type of output signal from the Switching on COMPONENT video jacks on this unit. 1 Connect the AC power cord to the power outlet. 2 Switch on the TV and this unit. 3 Set the TV to the correct Video IN channel. (e.g. EXT1, EXT2, AV1, AV2, AUDIO/VIDEO, etc. Refer to your TV owner’s manual for detail.) ➜ The front panel display lights up and the default screen appears on the TV. 4 If you are using an external equipment (e.g. audio system
Summary of the content on the page No. 15
English Preparation 1Menu Language (see page 17) 5Analog output (see page 16) You can select the language displayed in the On-screen Enables you to specify the type of analog output suitable menu. for your AV receiver. Select [Multi-channel] if you are 1 Go to [Menu Language] (Setup ➔ Language ➔ Menu using a multi-channel AV receiver with 6-ch discrete Language) by using k n l h buttons on the remote inputs. If your AV receiver does not have 6-ch discrete control, then press h. inputs, selec
Summary of the content on the page No. 16
On-screen menu The On-screen menu enables you to customize this unit Adv.Picture to suit your requirements. Allows you to fine-tune the following video parameters. 4:3 Aspect General operation You can adjust the aspect ratio of the projected images on the screen. This function is only available for 1 Press ON SCREEN on the remote control. progressive scan and HDMI video output. ➜ The On-screen menu appears on the screen. Select [NL_Stretch] for display of 4:3 image on the 16:9 screen with no
Summary of the content on the page No. 17
English On-screen menu HDMI Video Saturation Enables you to adjust the resolution depending on the Adjusts the video color saturation. This function is not monitor you are using. You can use this function only available for signals output from COMPONENT video jacks and HDMI video signals. when the HDMI output terminal is connected to a Choices: –7 to +7 HDMI-compatible component. Initial setting: 0 Choices: 480p, 576p, 720p, 1080i, Auto Initial setting: 480p (U.S.A. model) Contrast 576p (U.K
Summary of the content on the page No. 18
On-screen menu Night mode Angle When set to [On], the dynamics of the sound output is Some DVD discs feature a multiple angle function, optimized. High volume output is softened, enabling enabling you to watch certain scenes from various you to watch your favorite action movie without angles. Function availability and the number of camera disturbing others. angles vary according to the disc. Choices: On, Off Page Initial setting: Off Turns pages of DVD-Audio still images. Toolbar Play option
Summary of the content on the page No. 19
English On-screen menu Slide Show TV Use this feature for JPEG slide show playback. TV shape If you connect to a conventional 4:3 aspect TV, select Picture time [4:3 panscan] (the left and right sides are trimmed when Sets the duration for each image. you play 16:9 video) or [4:3 letterbox] (black areas Choices: Slow, Medium, Fast appear at the top and bottom when you play 16:9 video). Initial setting: Medium Select [Widescreen] if you connect to a Wide-Screen TV. Choices: 4:3 panscan, 4:3
Summary of the content on the page No. 20
On-screen menu PCM output Audio Menu Enables you to select PCM digital output at 48 kHz or Digital output 96 kHz. If you select [48 KHz], PCM data will be Enables you to specify the type of digital output that best converted to 2-ch 48 kHz or less. Select [48 KHz] if the suits your AV receiver or HDMI monitor/receiver. connected equipment cannot process signals with a Select [PCM only] if your receiver or HDMI monitor/ sampling frequency of 96 kHz or 88.2 kHz. receiver is not capable of deco
