Summary of the content on the page No. 1
GX-1 Disc Publisher
®
For Microsoft Windows 2000 & XP
Users Manual
Microboards Technology LLC Version 1.1
Summary of the content on the page No. 2
2 • Introduction
Summary of the content on the page No. 3
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER TABLE OF CONTENTS INTRODUCTION ..............................................................................................................................................................4 WHAT’S INCLUDED ........................................................................................................................................................
Summary of the content on the page No. 4
Introduction The Microboards GX-1 Disc Publisher is a single drive, 50 disc, print and record system. The GX-1 combines industrial strength printing and recording into a single, easy to use duplicator. The system includes one 16x DVD recorder. Microboards and HP co-developed the printer technology, allowing up to 4800 x 1200 dpi printing. The Prassi Technology Zulu 2 software is a dynamic interface for both beginners and power users. Easily record DVD Video, DVD data, Audio CD’s, Dat
Summary of the content on the page No. 5
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER System Requirements The Microboards GX-1 Disc Publisher has the following minimum requirements and compatibilities: Operating System Microsoft Windows 2000 with SP4 or Windows XP with SP2. Processor Pentium 4 (or equivalent) CPU, running at 2.0 GHz or faster. System Memory Minimum 512 MB of system memory. More memory is suggested for DVD recording op
Summary of the content on the page No. 6
Installing Ink Cartridges Supported Ink Cartridges The GX-1 Disc Publisher uses a single color ink cartridge. The part number for this cartridge is GX- 200HC. If other cartridges are installed, the GX-1 Disc Publisher will not function. These cartridges are available from any Microboards reseller. Refill kits or non-Microboards ink cartridges are not recommended for use in the GX-1 Disc Publisher system. Use of these types of cartridges will cause the printer to fail. Use of these typ
Summary of the content on the page No. 7
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER Loading Discs The next step is to load your GX-1 Disc Publisher with output discs. The system will accept CD or DVD 120 mm (12 cm) inkjet printable discs. If the disc does not have an inkjet printable surface, the ink will not adhere to the surface of the disc. The GX-1 Disc Publisher will only accept 12 cm discs. Business card or 8 cm discs are not s
Summary of the content on the page No. 8
GX-1 Disc Publisher Installation The GX-1 Disc Publisher installation disk includes an Installer that will walk you through the process step by step. Please use the Installer and follow the installation steps in order. The following installation sections are intended only as a reference for the installation process, not as a guide to installing the GX-1 Disc Publisher. Performing the installation out of order could result in an unsuccessful installation. The GX-1 Disc Publisher Installa
Summary of the content on the page No. 9
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER Windows XP The Windows Found New Hardware Wizard will appear during any installation, including when using the Installer. Please follow all directions in the order in which they appear when using the Installer. Turn on power to the GX-1 Disc Publisher. Turn on power to the PC. Windows will now boot up and Windows XP will start stating that new hardware
Summary of the content on the page No. 10
5. Select No, not this time and click Next. 9. Click Next. 6. Click Next. 10. Click Continue Anyway. 7. Click Finish for the next screen. 11. Click Finish for the next screen. 8. Select No, not this time and click Next. 12. Select No, not this time and click Next. 10 • Assembly and Installation
Summary of the content on the page No. 11
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER 17. Click Next. 13. Click Next. 14. Click Continue Anyway. 18. Click Continue Anyway. 19. Click Finish. 15. Click Finish for the next screen. 16. Select No, not this time and click Next. 11
Summary of the content on the page No. 12
Setting Printer Alignment Alignment The GX-1 Disc Publisher system has been aligned at the factory. The factory alignment values are on a label on the back of the GX-1 Disc Publisher. Follow these steps to enter the factory values: • Click on the Start Button on your Windows computer. • Select Settings and then Printers. • Right click on the Microboards GX Series icon. • Select Printing Preferences. • Select the Utility Tab. • Click on the .1mm selection in the Resolution box. •
Summary of the content on the page No. 13
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER Print Alignment Disc NOTE: The Alignment Disc should always be printed using Photo mode for the best accuracy. There are factory default alignment values for the TOP and LEFT values for your GX-1 Disc Publisher, referring to the top and left margin sizes, respectively. These can be found on the label on the back of the GX-1 Disc Publisher. You may need
Summary of the content on the page No. 14
Printing Preferences Access the Printing Preferences by clicking the Start Button on your Windows computer. Select Settings and then select Printers. Right click on the Microboards GX Series icon, then select Printing Preferences. Paper/Quality Tab Print Quality • Best • Normal • Fast Print Modes • Text and Graphics • Photo Printing Recommendations Text and Graphics mode is used for printing mainly text information and small graphics. Below are some examples for images i
Summary of the content on the page No. 15
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER Advanced Features Advanced Features allow you to adjust the amount of ink placed on the disc using the Ink Volume setting, and adjust the Dry Time of the disc. Color Tab Saturation, Brightness and Color Tone allow you to fine tune your print image. Color Space defines the range of colors that can be printed.
Summary of the content on the page No. 16
Utility Tab The Resolution setting should always be set at .1mm for best results. Alignment values will move the print image on the disc. The Outer and Inner Diameters will change the size of the area to be printed. To avoid excessive ink buildup, these values should never be set so that the GX- 1 Disc Publisher is printing off the media. If you have media with a printable inner hub separated from the rest of the disc by an unprintable ring, you can set the inner and outer hub dia
Summary of the content on the page No. 17
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER The GX-1 Disc Publisher and Zulu2 All printing and burning is done using Zulu2. Do not print using SureThing, as SureThing does not control the loading and unloading process. The first time the user launches Zulu2, the software will ask you to configure the GX-1 Disc Publisher system. This only needs to be done the first time the software is used. Wh
Summary of the content on the page No. 18
You will see an entry labeled “USB Serial Port (COMx)” entry for each GX-1 Disc Publisher you have installed. The COMx will be the COM port number to be entered into the Configure screen. Select the COM port as found on the Computer Management screen. Next, select the recorder. Finally, select the Printer. To confirm you have made the correct selection, you can click on the T box next to each item, as follows: • When the T is pressed for the COM Port, the disc flippers
Summary of the content on the page No. 19
MICROBOARDS TECHNOLOGY, LLC GX-1 DISC PUBLISHER Manual Software Re-Installation The information in this section will only apply to a manual re-installation of the individual software packages. If you have not yet installed the GX-1 Disc Publisher using the Installer, it is recommended that you do so. Installing the GX-1 Disc Publisher in an incorrect order could result in an unsuccessful installation
Summary of the content on the page No. 20
If you wish to change the default Install directory, it can be done here. Click Next when completed. Next, you have options to add an icon to your desktop and/or a folder in the Start Menu. Once selected, click Next. Click Start to begin copying the files. The files will now be transferred from the CD to the operating system. Once completed, the finished screen will appear. You can choose to register the software online at this screen
