Summary of the content on the page No. 1
TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SD-C2732
DVD-ROM MOBILE DRIVE
USER MANUAL
Summary of the content on the page No. 2
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the DVD-ROM ................................................................4 Troubleshooting.......................................................................6 Specifications ..........................................................................7 Drive Connectors...............
Summary of the content on the page No. 3
INTRODUCTION – SD-C2732 General Features RoHS CompliantRPC2 Compliant 110ms Average Access Time (DVD) DVD+R DL, DVD±R, DVD±RW, DVD-RAM, CD-R and CD-RW Compatible Drive Speed DVD 8X CD-ROM 24X DVD-RAM 2X DVD±R, DVD±RW, DVD+R DL 4X BUS Interface ATAPI Types of Disc Formats Supported – DVD-ROM DVD-5 (single-sided, single layered) DVD-9 (singled-sided, double layered) DVD-10 (double-sided, single layered) DVD-18 (double-sided, double layered DVD-R (read, 3.9GB/4.7GB)
Summary of the content on the page No. 4
Eject Button The EJECT button is used to open the disc tray so you can install or remove a disc Busy Indicator When you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as it attempts to locate the disc. One of the following will occur: • BUSY light goes out. The DVD-ROM drive is ready to read data from the disc. • BUSY light flashes slowly. The disc may be dirty. • BUSY light remains ON. The DVD-ROM is accessing data. • BUSY light remains ON indefinitely. The DVD
Summary of the content on the page No. 5
SETUP – SD-C2732 Toshiba recommends that only trained professionals install this DVD-ROM drive into your laptop/notebook. Installation Notes • The SD-C2732 DVD-ROM drive has no jumpers that need to be set • Mounting orientation: 15° (horizontally), 15° vertically (volume control in down position), 30° (drive with volume control in up position). • When mounting drive use 4 M2-PO.4 tapping holes located on the left and right sides of drive. • When mounting drive, the tightening tor
Summary of the content on the page No. 6
USING THE DVD-ROM Drive – SD-C2732 Drive Operation Inserting Media – Horizontally or Vertically To insert a DVD in a DVD-ROM drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's loading tray by pressing the Eject Button and pulling out the tray. 2. Place media disc into drive's loading tray, and lightly press down on the inner portion of the disc. 3. Gently close the disc tray. Removing Media To remove media disc from
Summary of the content on the page No. 7
Regional Coding Region Protection Coding (RPC) of DVD Discs: this feature is supported on DVD Players and is used with DVD-Video Discs (i.e. movies). Currently, the motion picture industry has divided the world into different regional "zones." These regions or "zones" correlate to the regional markets into which the motion picture industry releases movies. Simply put, RPC Codes are placed on Movie Discs marketed throughout the world based on the region of the world where they are being so
Summary of the content on the page No. 8
TROUBLESHOOTING – SD-C2732 Problem Solution Disc tray cannot be opened • Check that there is power to drive. • Use Emergency Eject instructions to open tray. Drive is not recognized by • Is the drive connected properly? Are all cables plugged in system properly (e.g. Power Cable, Interface Cable and Audio Cables). • Is the software driver loaded? On a step-by-step (F8) Boot of the system is the DVD-ROM drive recognized? (BIOS / DOS reports "device driver not found" or "no val
Summary of the content on the page No. 9
SPECIFICATIONS –SD-C2732 General Interface: ATAPI Compatible DVD-ROM Standard - Read: DVD: DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) DVD-R (ver 1.0 & 2.1, read) DVD-RW (ver 1.0, 1.1 read) DVD+R, DVD_R DL, DVD+RW DVD-RAM (ver 2.1, read) CD-ROM: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video-CD), Multi-session (Photo CD Disc, CD-Extra, CD-R, CD-RW), CD-RW (read), CD-R (read) Note: All DVD/CD formats, except CD-Red Book (audio),
Summary of the content on the page No. 10
Transfer Rate DVD (Single) 4,460 – 10,816 Kbytes/s DVD (Dual) 3,380 – 8,112 Kbytes/s DVD±R/±RW 2,298 – 5,408 Kbytes/s DVD+R Double Layer 2,298 – 5,408 Kbytes/s DVD-RAM (Ver 2.1) 2,704 Kbytes/s CD (mode 1) 1,546 – 3,600 Kbytes/s CD (mode 2) 1,761– 4,104 Kbytes/s Rotational Speed DVD single layer: 4,670rpm (3.3X – 8X) DVD dual layer: 3,792rpm (2.5X – 6X) DVD-R (ver 1.0) 2,560rpm (1.7 – 4X) DVD-R (ver 2.1) 2,224rpm (1.7 – 4X) DVD±RW, DVD+R, DVD+R DL 2,224rpm (1.7 – 4X) DVD-RA
Summary of the content on the page No. 11
Power DC Voltage and Current Requirements +5V ±5% (Operating), 8% (start-up) Physical Height 0.5" (12.7mm) Width 5.04" (128mm) Depth 4.96" (126.1mm) Weight 6.0oz (.17kg) Connectors IDE Interface Connector 50 Pin I/F ATAPI Standard Regulatory The SD-C2732 DVD Writeable drive has been certified by the following regulatory agencies • UL 1950 • CSA C22.2 No. 950 • TUV (EN60950I) • CE standard • DHHS 21 CFR Sub-Chapter J • FDA CFR21, EN60825 9
Summary of the content on the page No. 12
Drive Connectors –SD-C2732 Figure 1.SD-C2732 DVD Writeable Drive Rear Panel – Connector A 50-pin ATAPI interface connector is found at the rear of the SD-C2732 DVD-ROM drive. ATAPI Connector Connecting cable should use Japan Aviation Electronics Industry Limited KX14-50Series L or equivalent connector. Table 1.Interface Pin Assignments PIN I/O SIGNAL NAME PIN I/O SIGNAL NAME NO. NO. 1 O Audio L-CH 2 O Audio R-CH 3 Audio Ground 4 Digital Ground 5 I /RESET 6 I/O DD8 7 I/
