Summary of the content on the page No. 1
INSTALLATION INSTRUCTIONS FOR PART 99-6510
APPLICATIONS
Chrysler
300 2005-2007
Aspen 2007
Dodge Jeep
Caliber 2007-2008
Commander 2006-2007
Charger 2005-2007
Compass 2007-2008
Durango 2005-2007
Grand Cherokee 2005-2007
Magnum 2005-2007
Patriot 2007-2008
Ram 1500 2006-2008
Ram 2500/3500 2006-2008
Designed For Vehicles With Factory Navigation Radios
Using this kit in vehicles without factory navigation requires the purchase of a factory
navigatio
Summary of the content on the page No. 2
99-6510 TABLE OF CONTENTS Dash Disassembly - Chrysler Aspen 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Dodge Durango 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - Dodge Charger 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Dodge Magnum 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Chrysler 300
Summary of the content on the page No. 3
DASH DISASSEMBLY 99-6510 CHRYSLER ASPEN 2007 DODGE DURANGO 2005-2007 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. 2 Remove (2) 7MM screws from the inside of the pocket facing upward. (Figure A) B 3 Unclip and remove the entire trim panel surrounding the radio and climate controls. (Figure B) 4 Remove (4) 7MM screws securing radio to dash and remove radio. (Figure C) C 5 Continue to kit assembly. 1
Summary of the content on the page No. 4
DASH DISASSEMBLY 99-6510 DODGE CHARGER 2005-2007 DODGE MAGNUM 2005-2007 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. 2 Unclip and remove entire panel surrounding radio and climate controls, including a/c vents. (Figure A) B 3 Remove (4) 7MM screws securing radio to dash and remove radio. (Figure B) 4 Continue to kit assembly. 2
Summary of the content on the page No. 5
DASH DISASSEMBLY 99-6510 CHRYSLER 300 2005-2007 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove entire panel surround- 2 ing radio and climate controls, including a/c vents and clock. (Figure A) 3 Remove (4) 7MM screws securing radio B to dash and remove radio. (Figure B) 4 Continue to kit assembly. 3
Summary of the content on the page No. 6
DASH DISASSEMBLY 99-6510 DODGE RAM 1500 2006-2008 WITHOUT CENTER CONSOLE RAM 2500/3500 2006-2008 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. 2 Open cup holder and remove (2) Phillips screws facing up on front edge of radio/climate control panel. (Figure A) B 3 Unclip and remove entire panel sur- rounding radio and climate controls, including a/c vents. (Figure B) 4 Remove (4) 7MM screws securing radio to dash and remove radio. 5 Continue to kit assembly.
Summary of the content on the page No. 7
DASH DISASSEMBLY 99-6510 DODGE RAM 1500 2006-2008 WITH MINI CENTER CONSOLE RAM 2500/3500 2006-2008 1 Disconnect the negative battery terminal A to prevent an accidental short circuit. 2 If vehicle has floor shifter, remove shifter knob. Remove center console inserts, if present. 3 (Figure A) Remove screws securing the rear center 4 console to the floor panel. Lift up on the rear center console to clear the gear shift B lever, if present. (Figure B) Remove screws securing the front center 5 conso
Summary of the content on the page No. 8
DASH DISASSEMBLY 99-6510 DODGE RAM 1500 2006-2008 WITH FULL CENTER CONSOLE RAM 2500/3500 2006-2008 1 Disconnect the negative battery terminal A to prevent an accidental short circuit. 2 If vehicle has floor shifter, remove shifter knob. Unsnap and remove console front top 3 cover (closest to the dash). (Figure A) Remove two 8 mm screws from under 4 console cover (previously removed). B Remove front section of console. (Figure B) 5 Loosen two 8 mm screws at bottom of dash. Unsnap lower panel. Re
Summary of the content on the page No. 9
DASH DISASSEMBLY 99-6510 JEEP GRAND CHEROKEE 2005-2007 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove panel from around radio including the vent on each side. (Figure A) B 3 Remove (4) 7MM screws securing radio to dash and remove radio. (Figure B) 4 Continue to kit assembly. 7
Summary of the content on the page No. 10
P R N D L DASH DISASSEMBLY 99-6510 DODGE CALIBER 2007-2008 JEEP COMPASS 2007-2008 JEEP PATRIOT 2007-2008 A Disconnect the negative battery terminal 1 to prevent an accidental short circuit. 2 Unsnap and move shifter trim to the side. 5 1 2 34 6 (Figure A) 3 (Compass and Patriot only) Unsnap and D remove top center dash panel above AC L vents. 4 Unsnap center dash trim panel (do not remove until climate controls are removed). (Figure A) 5 Remove (4) Phillips screws holding climate control panel t
Summary of the content on the page No. 11
DASH DISASSEMBLY 99-6510 JEEP COMMANDER 2006-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the (16) screws securing the radio trim panel. (Figure A) A 4 screws 4 screws 4 screws 4 screws 3 Unclip and remove the entire radio trim panel. (Figure B) B 4 Remove (4) 7MM screws securing radio to dash and remove radio. 5 Continue to kit assembly. 9
Summary of the content on the page No. 12
KIT ASSEMBLY 99-6510 DIN RADIO PROVISION WITH POCKET A 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket radio into the cage until secure. (Figure B) Snap the pocket into the radio 3 B housing. (Figure C) 4 Continue to final assembly. C 10
Summary of the content on the page No. 13
KIT ASSEMBLY 99-6510 ISO RADIO PROVISION WITH POCKET A 1 Mount the ISO Brackets to the radio with the screws supplied with the unit. (Figure A) 2 Slide the radio into the radio opening until the side clips engage. (Figure B) Snap the ISO Trim Plate into the 3 B radio housing. (Figure C) 4 Snap the pocket into the radio housing. (Figure C) Continue to final assembly. 5 C 11
Summary of the content on the page No. 14
KIT ASSEMBLY 99-6510 DOUBLE DIN RADIO PROVISION A 1 Cut and remove center divider in radio housing. (Figure A) 2 Snap the DDIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the DDIN radio unit into the DDIN bracket/radio housing assembly and secure the radio unit B to the kit using the screws sup- plied with the radio unit. (Figure C) 4 Snap the DDIN trim-plate onto the housing/radio assembly. (Figure D) 5 Continue to final assembly. C D 12
Summary of the content on the page No. 15
KIT ASSEMBLY 99-6510 STACKED ISO UNITS PROVISION A 1 Cut and remove center divider in radio housing. (Figure A) Snap the DDIN brackets to the 2 inside edge of the radio housing. (Figure B) 3 Slide the stacked ISO DIN radio units into the DDIN bracket/radio housing assembly and secure the B unit to the kit using the screws supplied with the units. (Figure C) Snap the DDIN trim-plate onto the 4 housing/radio assembly. (Figure D) Continue to final assembly. 5 C D 13
Summary of the content on the page No. 16
FINAL ASSEMBLY 99-6510 FINAL ASSEMBLY A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disass
