Our goal is to provide you with a quick access to the content of the user manual for Haier 20AL25S. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Haier 20AL25S.
If looking through the Haier 20AL25S user manual directly on this website is not convenient for you, there are two possible solutions:
Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Haier 20AL25S but the selected pages only. paper.
Below you will find previews of the content of the user manuals presented on the following pages to Haier 20AL25S. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.
Please read this manual carefully
before using this TV set and keep it
for future reference.
Warning WARNING RISK ELECTRIC SHOOK DO NOT OPEN WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel. Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance
Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Read all of the instructions before using this appliance. When using this appliance, always exercise basic safety precautions, including the following: 1)Save these Instructions ---the safety and operating instructions should be retained for future reference. 2)All warning on the appliance and in the operating instructions should be followed. 3)Cleaning --- Unplug from the wall outlet before cleaning. Do not use liquid clean
Safety Instructions b.If liquid has been spilled, or objects have been fallen into the unit. c.If the unit has been exposed to rain or water. d.If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal
To users: Thank you for purchasing our LCD-TV. Before connecting the LCD-TV and turning on the power, please read this book carefully. Please keep this book for later use. If the unit is disabled by an electrostatic discharge, please turn off the power to the unit and turn it back on to reset. CONTENT Front Panel Controls.................................................................................. 2 Connection Options.........................................................................
Front Panel Controls HLE20BB 2 3 4 1 5 7 6 HLH15BB 2 3 4 1 7 65 1 2 3 4 5 TV/AV MENU VOL- VOL+ CH- CH+ POWER 15HL25S/20AL25S HLH19W HLH19BB 6 7 7 6 6 7 Control Panel Function 1.TV/AV Selects the input signals: PC/COMPONENT/AV/SV/TV 2. MENU Press to select the main menu 3. VOL-(V-) Volume down / Left orientation to adjust the item in the OSD VOL+ (V+) Volume up / Right orientation to adjust the item/Press to enter 4. CH
Connection Options HLH15BB/15HL25S/HLE20BB/20AL25S (The figure is just for reference, please see actual unit. ) AV /S-VIDEO/COMPONENT Audio Input Connect audio DC Power Cord Socket output from an external Antenna Input This TV operates on DC device to these jacks Connect cable or power. The voltage is antenna signals to indicated on the specifications the TV, either direc- page. Never attempt to tly or through your operate the TV on ac power cable box. Pb Y Pr L R V
Pr Pb Y R L V ANT IN PC AUDIO IN AUDIO IN VIDEO IN S-VIDEO COMPONENT IN VGA IN Pr Pb Y R L V ANT IN PC AUDIO IN AUDIO IN VIDEO IN S-VIDEO COMPONENT IN VGA IN Connection Options HLH19BB/HLH19W The figure is just for reference, please see the real. And the AC power supply switch is on the back of the set) Antenna Input Connect cable or antenna signals to the TV, either direc- tly or through your cable box. Earphone port PC Audio Input AV/S-
Remote Control Key Functions When using the remote control, aim it towards the remote sensor on the TV MUTE 1 2 RECALL D IS P L AY E X IT 3 4 5 1 2 3 4 5 6 6 7 8 9 MTS/SAP P.STD 7 0 8 MENU TV/AV 9 10 CH+ 11 VOL VOL - + CH- 12 13 14 CCD SLEEP S C A N 15 Illustration of the keys on the remote control: 1. MUTE MUTE 2. Power supply switch 3. RECALL Quick TV channel switch(return to the last channel) 4. EXIT Menu exit 5. DISPLAY Display current input signal information TV channel
Remote Control Installing Batteries 1.Slide open the cover of the battery compartment on the back of the remote control. 2.Load two AAA alkaline batteries in the compartment. (plus and minus poles to respective mark) 3.Replace the cover of the battery compartment. Precautions As strong light may interfere with the Make sure that there is no signals, change your position to obstacle between the remote operate the remote control if controller and television set. the television cannot b
Connection Instructions The connection instructions shown here are for model HLH15BB for reference only. May differ with the other models mentioned. Grounding Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. External Equipment Connections Antenna Connecti
Connection Instructions PC Setup You can use your LCD-TV as a monitor for your personal computer using a VGA cable (not supplied). Connection and use steps: 1.Read the user guide supplied with your computer and ensure that it has a VGA connector; 2.Make sure that the power of the LCD D-SUB IN -TV and the PC are off; 3.Connect a D type 15-pin VGA interface cable ( not supplied ) to the VGA video interface connector on the PC. Then connect the other end to the VGA video
Connection Instructions VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and TV Connection and use steps: 1.Read the user guide supplied with your AV devices and ensure that it has Composite or S-Video connectors; 2.Make sure that the power of the LCD-TV and the AV device are off; Connection Option 1 Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Connection Option 2 1. Connect the audio and video cables from V
Connection Instructions Cable TV Setup - After subscribing to a cable TV service from a local provider you can watch cable TV programming. The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV. - For further information regarding cable TV service, contact your local cable TV service provider(s). Connection Option 1 1. Select 3 or 4 with channel switch on cable box. 2. Tune the TV channel to the same selected output channe
Basic Operating Instructions Turn on the LCD-TV When the POWER button is pressed and the LCD-TV MUTE is turned on, the indicator light on the front of the LCD-TV R E C A L L D I S P L A Y E X I T changes from red to green. When the LCD-TV is turned off 1 2 3 using the power button, the LCD-TV will go into standby 4 5 6 mode and the indicator light turns red. 7 8 9 MTS/SAP P.STD 0 MENU TV/AV Note: CH+ VOL VOL The display of the input mode - + TV CH- will disappear in 3 seconds. C
Basic Operating Instructions Select the TV Channel You Want You can use the number keys on the remote control to directly select TV channels. The LCD-TV can store up to 181 channels , and you can press the keys on the remote control or on the panel to make a selection. Picture Mode Press P.STD button on the remote control for menu display . For desired mode as follows: PERSONAL STANDARD MILD FRESH Program Scan Press SCAN button to scan through all the memorized TV channels. The scan will paus
Menu Operations * In this manual, the OSD (On Screen Display) may be different from your TV s because it is just an example to illustrate the TV operation. Press TV/AV to select the input source, and the menu for each source is different . 1. Press MENU button to display the main menu, and VOL+/VOL-to select the main menu . 2. Press CH+/CH- to scroll through the parameters 3. Press VOL+/VOL- buttons to make changes to the parameters 4. Press the EXIT button to exit the menu Picture
Menu Operations Picture Menu Options continued 2. Press CH+/CH- button to enter the picture menu and to go up and down to select the desired option . 3.Press VOL+/VOL- button to increase and decrease the level to adjust the selected option to your preference . 4. Repeat step 2 and step 3 until desired picture quality has been achieved . Function: BRIGHTNESS :Adjust the brightness of the picture . By increasing the level, it will add more light to dark parts of the picture and by dec
Menu Operations Sound Menu Options continued You can adjust sound options to the levels you prefer. 2. Press CH+/CH- button to enter the audio menu and to go up and down to select the desired option . 3.Press VOL+/VOL- button to increase and decrease the level to adjust the selected option to your preference . 4. Repeat step 2 and step 3 until desired sound quality has been achieved .. Function : VOLUME : Adjust the volume of your TV BALANCE : Adjust the balance of the audio output
Menu Operations Function Menu Options Menu Language Selection: The menus can be shown on the screen in the selected language. First select your language. 1. Press MENU button and VOL+/VOL- until the following menu appears on the screen. FUNCTION INPUT SOURCE TV LANGUAGE ENGLISH CC MODE OFF BLUE SCREEN ON RESET 2. Press CH
|1||Haier 1509-A||Flat Panel Television||239|
|2||Haier 42EP24STV||Flat Panel Television||96|
|3||Haier 42HP25SAT||Flat Panel Television||46|
|4||Haier 42EP25BAT||Flat Panel Television||17|
|5||Haier 50HP25BAT||Flat Panel Television||58|