Summary of the content on the page No. 1
USER’S MANUAL
RLDED3950A
39” LED TV
Summary of the content on the page No. 2
Contents Introduction Warning Caution Important Information Attaching or Removing the Stand Installing Batteries to the Remote Control Identifying Front and Rear Panel Connection Suggestion Main Unit Description Remote Control OSD Basic Adjustment How Do I Clean The TV Troubleshooting Specifications FCC Compliance Statement 1
Summary of the content on the page No. 3
Introduction Thank you very much for purchasing your LED TV. It serves as a normal colour TV and a PC monitor. To enjoy your set fully from the very beginning, read this manual carefully and keep it handy for future reference. INSTALLATION ① Locate the receiver in the room where direct light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. ② Allow enough space betwee
Summary of the content on the page No. 4
Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to avoid the risk of electric shock. This equipment may only be disassembled by qualified service personnel. This symbol is intended to alert the user to t
Summary of the content on the page No. 5
Caution Caution High voltages are used in the operation of this product. - Do not open the product's casing. Refer servicing to qualified service personnel . Caution To prevent fire or electrical shock hazard, do not expose the main unit to rain or moisture，do not place objects filled with liquids, such as vases, on the apparatus. Caution Do
Summary of the content on the page No. 6
Caution Caution Never stand on, lean on or suddenly push the product or its stand. You should pay special attention to children. Caution Do not place the main unit on an unstable cart stand, shelf or table. Serious injury to an individual and damage to the television may result if it should fall. Caution When the product is not used for an extended period of time
Summary of the content on the page No. 7
Important Information Television Antenna Connection Protection External Television Antenna Grounding If an outside antenna or cable system is to be connected to the TV, make sure that the antenna or cable system is electrically grounded to provide some protection against voltage surges and static charges. Article 810 of the National Electrical Code, ANSI/NFPSA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in
Summary of the content on the page No. 8
Attacthing or Removing the Stand 1. To attach the base place the display unit flat on a table. Afterwards attach the stand onto the bottom of the stand. Screw in the 5 screws to secure the stand. 7
Summary of the content on the page No. 9
2. To remove the stand, remove the 4 screws in the area and the stand will come off. Installing Batteries to the Remote Control Please insert two AAA batteries into the remote control. Make sure that you match the (+) and (-) symbols on the batteries with the (+) and (-) symbols inside the battery compartment. Afterwards, re-attach the battery cover. Please note: � Only use AAA batteries. � Do not mix new and old batteries. This may result in crackin
Summary of the content on the page No. 10
Identifying Front and Rear Panel Front View INDICATOR LIGHT – The light is red when power is plugged in but the TV is not turned on. The light turns blue when the TV is turned on. Because of the LED in the panel, the TV might take 10 – 12 seconds to power on. REMOTE SENSOR – The remote sensor receives all the commands from the remote control. Rear View Mounting Pattern Mounting Specification : 200mm x 200mm using screw size M6. Length of
Summary of the content on the page No. 11
Connection Suggestions If You Have Digital Cable without Cable Box or Antenna… 1. Make sure the power of HDTV is turned off. 2. Connect the RF cable from your antenna or digital cable to the TV port on the back of your HDTV. 3. Turn on the HDTV. 4. Follow the first time on screen instructions. Please Note: Not all broadcasts are in High Definition (HD). Please refer to your local broadcasting stations for more information
Summary of the content on the page No. 12
Connecting DVD Player with Component YPbPr… 1. Make sure the power of HDTV and your DVD player is turned off. 2. Obtain a Component Cable. Connect the green color connector to both your DVD player and YPbPr’s green connector port on the back of your HDTV. 3. Connect the blue color connector to both your DVD player and YPbPr’s blue connector port on the back of your HDTV. 4. Connect the red color connector to both your DVD player and YPbP
Summary of the content on the page No. 13
Connecting Wii™ with Composite… 1. Make sure the power of HDTV and your Wii™ is turned off. 2. Obtain a Yellow Video Cable. Connect the Yellow Video connector to both your Wii™ and AV’s Yellow Video connector port on the back side of your HDTV. 3. Obtain a RCA Audio Cable. Connect the white color connector to both your Wii™ and AV’s white connector port on the back side of your HDTV. 4. Connect the red color connector to both you
Summary of the content on the page No. 14
Connecting Cable or Satellite boxes with HDMI… 1. Make sure the power of HDTV and your set-top box is turned off. 2. Connect a HDMI cable to the HDMI output of your set-top box and the other end to the HDMI port on the back of your HDTV. 3. Turn on the HDTV and your set-top box. 4. Use the remote control’s source button or the source button on the TV to switch to HDMI. Please Note: Please reference the set-top box’s manual,
Summary of the content on the page No. 15
Connecting to a PC with VGA and 3.5 mm minijack … 1. Make sure the power of HDTV and your PC is turned off. 2. Obtain a 15-pin D-Sub VGA cable; connect to the VGA output of your PC and the other end to the VGA port on the back of your HDTV. 3. Obtain a 3.5 mm Mini-jack, connect to the audio out of your PC and the other end to the VGA Stereo Input port. 4. Turn on the power of the HDTV and your PC. 5. Use the remote control’s source but
Summary of the content on the page No. 16
Connecting a Digital Audio Receiver with Coaxial... 1. Make sure the power of HDTV and your receiver is turned off. 2. Obtain a COAXIAL cable, connect it to your receiver’s COAXIAL digital input and the COAXIAL connection on the LINE OUT port on the back of the HDTV. 3. Turn on the HDTV and your receiver. Please Note: If you want pure digital stream for your receiver to decode, you must also configure the TV’s OSD Sound
Summary of the content on the page No. 17
Main unit description Control Panel Button Function VOL+ : Volume up. VOL- : Volume down. CH+ : TV channel up. CH- : TV channel down. MENU : Press to select the main menu. TV/AV : Select the input signal. POWER : Switch on when at standby mode or enter the standby mode. TV Terminal Connections 1. Coaxial out terminal. 2. RF antenna. 3. VGA input terminal of simulation signal of PC. 4. PC AUDIO input terminal. 5. Video input terminal. 6. AUDIO input terminal（Audio
Summary of the content on the page No. 18
Remote control POWER: Power on/off button, press once to turn the TV on and press again to turn the TV off. MUTE: Press this button to mute or restore sound. MTS/AUDIO: When stereo program is received, press this key to switch sound system between mono and stereo. When SAP program is received, press this button to switch sound system between mono and SAP When stereo and SAP program is received, press this key to switch among mono, stereo and SAP. Press this key to show the l
Summary of the content on the page No. 19
Installation Guide Press MENU button to display the MAIN OSD MENU; Press ◄ / ►button to select the MENU you want; Press ENTER button to enter the sub menu; Press ▼ / ▲ button to select the option and then press ◄ / ► to adjust the value in the sub menu; You can press MENU button to go back to the upper menu or EXIT button to close the OSD. PICTURE Press ENTER when the Picture Settings item is highlighted. Then you will go to the sub-menu as following. Press ▼ / ▲ to select
Summary of the content on the page No. 20
Press ▼ / ▲ button to select Brightness, then press ◄ / ► button to adjust. . Press ▼ / ▲ button to select Contrast, then press ◄ / ► button to adjust. . Press ▼ / ▲ button to select Color, then press ◄ / ► button to adjust. . Press ▼ / ▲ button to select Tint, then press ◄ / ► button to adjust. Press ▼ / ▲ button to select Sharpness, then press ◄ / ► button to adjust. . Screen Size Press ▼ / ▲ button to select Screen Size, then press ◄ / ► button to adjust. PC Settings Note : The
