Summary of the content on the page No. 1
Installation and Wire
English connection manual
VRX630
Installation and Wire connection manual
Contents
1. BEFORE STARTING ................................................................ 43
2. PACKAGE CONTENTS ............................................................ 43
3. GENERAL CAUTIONS............................................................. 44
4. CAUTIONS ON INSTALLATION .............................................. 44
5. INSTALLING THE MAIN UNIT .................................
Summary of the content on the page No. 2
Installation and Wire English connection manual 3. GENERAL CAUTIONS 1. Do not open the case. There are no user ser- 2. Use a soft, dry cloth to clean the case. Never viceable parts inside. If you drop anything into use a rough cloth, thinner, benzine, or alco- the unit during installation, consult your hol, etc. For tough dirt, apply a little cold or dealer or an authorized CLARION service warm water to a soft cloth and wipe off the centre. dirt gently. 4. CAUTIONS ON INSTALLATION 1. Prepare a
Summary of the content on the page No. 3
Installation and Wire English connection manual 5. INSTALLING THE MAIN UNIT Universal Mount 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. 2. Wire as shown in Section 8. Notes: 3. Insert the main unit into the universal mount- 1) Some car models require special mounting kits ing bracket until it locks. for proper installation. Consult your Clarion
Summary of the content on the page No. 4
Installation and Wire English connection manual Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) This unit is designed for fixed installation in the same for the other side to remove the springs dashboard. from the both sides. (Figure 7) If the vehicle is equipped with a factory-installed 2. Secure the mounting brackets to the chassis radio, install the main unit with the parts and as shown in Figure 8. Holes are pre-tapped screws marked (∗). (Figure 8) for TOYOTA and NISSAN ve
Summary of the content on the page No. 5
Installation and Wire English connection manual 6. REMOVING THE MAIN UNIT A the spring into hole of the hook plate, then 1. When the rear of the main unit has been se- cured with the method shown in Figure 6 pull the main unit out by the hook plate. (In- sert both the right and left edges of the hook unfasten the special screw. plate.) (Figure 9) 2. Remove the outer escutcheon. 3. Insert the hook plate between the spring and Note: Keep the hook plate. You cannot remove the the universal mounti
Summary of the content on the page No. 6
Installation and Wire English connection manual 8. WIRE CONNECTION VISUAL/CCD/DVD changer terminal AUDIO 4CH. OUTPUT terminal Red Gray Front right White Gray Front left Red Brack Rear right White Rear left Brack ∗1:Connect securely to the metal part of the vehicle with a screw, etc. ∗2:Connect to the power supply terminal which can be turned on and off by the ignition switch. ∗3:Connect to the power supply terminal where the power is always supplied regardless of whether the ignition switch is
Summary of the content on the page No. 7
Installation and Wire English connection manual Connecting the Accessories Connection to the external amplifier • The external amplifier can be connected to the AUDIO 4CH. OUTPUT terminal (RCA pin jack) on the main unit. In other words, it can be connected provided the DSP is connected. Connection to the CCD camera for vehicle • The CCD CAMERA for vehicle can be connected to the system expansion terminal on the main unit. For detailed information, refer to the instruction sheet or manual for
Summary of the content on the page No. 8
Installation and Wire English connection manual 9. SAMPLE SYSTEMS Sample System 1 Main Unit (VRX630) ∗To enable the correct input, it is necessary to configure the VRX630 as described on page 30. VISUAL/CCD/DVD changer terminal AV Adapter cable VIDEO INPUT terminal (CCA-389, sold separately) CeNET cable (included the TV tuner) RCA video cable (included the TV tuner) TV Tuner (TTX7501z) CeNET Cable (included the Changer) Ferrite clamp (Included the DVD changer) CeNET Y-adapter (CCA-519-601,
Summary of the content on the page No. 9
Installation and Wire English connection manual Sample System 2 Main Unit Amp remote (VRX630) RCA PIN cable Front (Sold separately) Speakers Amp. Rear VISUAL/CCD/DVD changer terminal Speakers AV Adapter cable (CCA-389, sold separately) VIDEO INPUT terminal CeNET cable (included the TV tuner) RCA video cable (included the TV tuner) Rear Monitor ∗Images from the DVD changer RCA video cable (sold separately) TV Tuner cannot be displayed. (TTX7501z) AV Adapter cable (CCA-389, sold separately)
Summary of the content on the page No. 10
Installation and Wire English connection manual Sample System 3 Main Unit (VRX630) VIDEO INPUT terminal RCA video cable (included the TV tuner) CeNET cable Mini DIN(8P) Cable (included the TV tuner) (included the CCD camera) TV Tuner (TTX7501z) CCD camera ∗ To enable the correct input, it is Amp remote necessary to configure the VRX630 as described on page 30. CeNET Cable (included the DPH910) Front Speakers 4-channel Power Amplifier Rear Speakers RCA PIN cable (included the DPH910) Amp re
