Edelbrock 1553 user manual

User manual for the device Edelbrock 1553

Device: Edelbrock 1553
Category: Log Splitter
Manufacturer: Edelbrock
Size: 0.45 MB
Added : 6/20/2014
Number of pages: 8
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Edelbrock 1553. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Edelbrock 1553.

For your convenience

If looking through the Edelbrock 1553 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Edelbrock 1553 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Edelbrock 1553 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Edelbrock 1553 User manual - Online PDF
Advertisement
« Page 1 of 8 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Edelbrock 1553 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Edelbrock 1553. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

EDELBROCK E-FORCE SUPERCHARGER KITS
®
Part #1551, 15511, 1552, 15521, 1553, 15531, 1554,
15541, 15611, 15621, 15631, 15641
INSTALLATION INSTRUCTIONS
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,
it is recommended to have the installation completed by a qua

Summary of the content on the page No. 2

BEFORE BEGINNING INSTALLATION (CONTINUED) If the valves are not properly seating, or the valve lash is not properly adjusted, the increased temperatures created by the increased power output could accelerate valve seat wear and cause burnt valves. If for any reason your engine has oil pressure that is below the acceptable service limits as specified in the Factory Service Manual, this problem should be corrected before installing this supercharger kit. Be sure to verify you have all parts listed

Summary of the content on the page No. 3

KIT CONTENTS FOR STANDARD V-BELT DRIVE ACCESSORIES FOR BILLET SPECIALTIES TRU TRAC PULLEY SYSTEM ❑ 1 Supercharger/Manifold Top Plate Assembly ❑ 1 Supercharger/Manifold Top Plate Assembly ❑ 1 Supercharger Intake Manifold ❑ 1 Supercharger Intake Manifold ❑ 1 Supercharger Snout Support/Idler Pulley Bracket ❑ 10 3/8-16 x 1.25” Long Bolt (Intake Manifold) ❑ 1 Alternator Support Bracket Standard Bolt Pattern Kits Only ❑ 1 Idler Pulley ❑ 2 3/8-16 x 1.75” Long, .625” Shoulder Bolt (Intake Manifold) ❑ 1

Summary of the content on the page No. 4

PARTS REMOVAL AND PREPARATION 1. Make sure vehicle is on level ground, and the wheels are chocked. E. Remove distributor. Do not rotate engine after Disconnect battery. removing distributor. 2. Loosen tension on accessory belts and remove belts. Remove 12. Remove Intake Manifold bolts and remove intake manifold. alternator tensioning bracket (upper bracket) from water pump. 13. GASKET SURFACE PREPARATION: 3. Remove crankshaft pulley bolts and remove accessory pulley. NOTE: This is a MUST to ensu

Summary of the content on the page No. 5

INSTALLATION PROCEDURE 1. With the intake gaskets in place, apply a small amount of RTV High Temp silicone sealer around the water passages on the intake manifold side (See Figure 4). NOTE: If you are using an air/fuel ratio meter (O2 sensor) on your vehicle, use 02 sensor safe silicone ONLY. Install Outermost Bolts ONLY Figure 4 Figure 7 2. With the Edelbrock intake manifold, you must use RTV High Temp silicone sealer instead of end seal gaskets. Apply a 1/4" thick bead 4. Install the provided

Summary of the content on the page No. 6

6. For 1986 and earlier applications, install the top plate to intake manifold bolts and torque bolts to 8-10 ft./lbs. On E-Tec/Vortec applications, install the top plate to manifold bolts and snug down with a small box end wrench. You may now install the remaining four (4) intake manifold bolts (that pass through the top plate) and tighten all of the manifold bolts to 11 ft./lbs by the sequence shown in Figure 10. Then torque the remaining top plate to manifold bolts to 8-10 ft./lbs. Tighten bo

Summary of the content on the page No. 7

11. Supercharger and Accessory Drive Belts: 17. Replace spark plugs with the recommended heat range and reconnect all ignition and spark plug wires. Make sure the spark A. Standard drive kits will require you to install your plug wires are installed in the proper order, and that the rotor in the accessory drive belts prior to installing the supercharger distributor is pointing to the same location on the distributor housing drive belt. Reinstall any bracketry that was attached to the as it was w

Summary of the content on the page No. 8

VACUUM ROUTING Bypass Valve Vacuum Supply: DO NOT REMOVE Manifold Vacuum/Boost Port: This port should be used for any boost-indexed ignition retard device. Standard Vacuum Ports: Any accessory that is vacuum-driven should be connected here. This includes brake boosters, some transmission kickdowns, and any vacuum actuated servos such as windshield wipers, power windows, etc. ® Edelbrock Corporation • 2700 California St. � Torrance, CA 90503 Tech-Line: 1-800-416-8628 Edelbrock E-Force Supercharg


Alternative user manuals
# User manual Category Download
1 Agri-Fab 25-0126 User manual Log Splitter 1
2 American DJ Splitter User manual Log Splitter 2
3 Ariens 917001 User manual Log Splitter 5
4 Bil-Jax 0108-0104H User manual Log Splitter 0
5 Black Box AC156A-8 User manual Log Splitter 1
6 Black Box AVSP-DVI1X2 User manual Log Splitter 2
7 Black Box AVSP-DVI1X4 User manual Log Splitter 2
8 Black Box AVSP-DVI1X8 User manual Log Splitter 0
9 Black Box CAT5 Audio/Video 8-Port Broadcaster User manual Log Splitter 1
10 Black Box User manual Log Splitter 0
11 Bolens 247-638-000 User manual Log Splitter 0
12 Bolens 24642L User manual Log Splitter 0
13 Bolens 244-645-000 User manual Log Splitter 0
14 Bolens 248-645A User manual Log Splitter 0
15 Bolens 24645L User manual Log Splitter 0