Toshiba 50A50 55A60 user manual

User manual for the device Toshiba 50A50 55A60

Device: Toshiba 50A50 55A60
Category: Flat Panel Television
Manufacturer: Toshiba
Size: 2.66 MB
Added : 7/23/2014
Number of pages: 50
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Toshiba 50A50 55A60. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Toshiba 50A50 55A60.

For your convenience

If looking through the Toshiba 50A50 55A60 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Toshiba 50A50 55A60 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Toshiba 50A50 55A60 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Toshiba 50A50 55A60 User manual - Online PDF
Advertisement
« Page 1 of 50 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Toshiba 50A50 55A60 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Toshiba 50A50 55A60. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

FILE NO. 020-200012
SERVICE MANUAL
COLOR TELEVISION
N0NSP Chassis
50A60, 50A50
(TAC0050) (TAC0051)
55A60, 61A60
(TAC0052)
(TAC0053)
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN
PUBLISHED IN JAPAN, May., 2000 S

Summary of the content on the page No. 2

TABLE OF CONTENTS CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS ........................................................................................................................................ 3 CRT ASSEMBLY REPLACEMENT AND MOUNTING ............................................................................................. 4 PICTURE TUBE COMPONENTS ADJUSTMENT.................................................................................................... 6 REPLACEMENT OF THE

Summary of the content on the page No. 3

CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous 2. This receiver is equipped with a Fail Safe (FS) circuit which X-RAY RADIATION. To avoid such hazards, the high volt- prevents the receiver from producing an excessively high age must not be above the specifie

Summary of the content on the page No. 4

CRT ASSEMBLY REPLACEMENT AND MOUNTING CAUTION : DO NOT LOOSEN THE HEX HEAD BOLTS WITH SPRINGS (12 PCS), BECAUSE THOSE ARE FOR SEALING OF CRT COOLANT. R GB Attention Serviceman The Hex Head Bolts with Springs. (see sketch) used on 8 o’clock CRT assembly, are “NOT” Adjustment Screws 4 o’clock DO NOT LOOSEN-FLUID LEAKAGE WILL OCCUR. 4 Screws 4 Screws Lens Assembly CRT Assembly CRT Anode Cap Assembly S.V.M. Coil CRT Mounting CRT DRIVE Board Deflection Yoke and Conver Yoke Lens and Neck Components V

Summary of the content on the page No. 5

TO REMOVE CRT (Same procedure for R, G, B) 1. Remove CRT DRIVE Board, S. V. M. COIL and DEF. YOKE from CRT. 2. Remove Lens Assembly. 3. Detach CRT Anode Cap from CRT. 4. Remove CRT Assembly from CRT Mounting. Anode Cap CRT REPLACEMENT (Same procedure for R, G, B) Reverse the removal procedures except the followings. 1. Anode Cable should be replaced with new one. See “SERVICING PRECAUTIONS” shown below. 2. Install silicon (T461B) to the CRT, replace the Anode cable and put enough silicon again o

Summary of the content on the page No. 6

WARNING : BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRE- CAUTION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF THIS MANUAL. PICTURE TUBE COMPONENTS ADJUSTMENT DESCRIPTION OF NECK COMPONENTS TILT ADJUSTMENT Rotate R, G, B deflection yoke so that picture becomes 1 2 horizon, then fasten screw. CENTERING ADJUSTMENT 1. Stretch a thread between two center slots of screen edge (top and bottom, left and right). 1 Deflection yoke and convergence yoke The position on th

Summary of the content on the page No. 7

LOCATION OF SCREEN AND FOCUS VR’S SCREEN VR FOCUS VR RG B – 7 – SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS

Summary of the content on the page No. 8

REPLACEMENT OF THE CRT Service parts are provided for each R, G and B. The contents of the parts are as follows. RG B 50A50 23796001 23005397 23796003 50A60 23005114 23005115 ↑ HITACHI 55A60 23005242 ↑↑ CRT 61A60 23005249 ↑ 23796486 REPLACEMENT OF HIGH VOLTAGE CABLE 1. When replacing Anode Lead or Anode Cap with new one, remove Lead Holder from old lead as shown in ANODE LEAD figure below, and put it on new lead. Do not throw away Lead Holder. NOTE : THE LEAD HOLDER IS ATTACHED TO TPA5007 (Z450)

Summary of the content on the page No. 9

SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press MUTE button once 2) Press MUTE button 3) While pressing the MUTE button, on Remote Control. again to keep pressing. press MENU button on TV set. S MUTE (Service mode display) 2. DISPLAYING THE ADJUSTMENT MENU 1) Press MENU button on TV. Service mode Adjustment mode Item Press S Data Press 3. KEY FUNCTION IN THE SERVICE MODE The following key entry during display of adjustment menu provides special functions. Screen adjustment mode ON/OFF: TV (

Summary of the content on the page No. 10

4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING & ADJUSTING DATA on page 17) 5. ADJUSTING THE DATA 1) Pressing of VOLUME s or t button will cahnge the value of data in the range from 00H to FFH. The variable range depends on the adjusting item. 6. EXIT FROM SERVICE MODE 1) Pressing POWER button to turn

Summary of the content on the page No. 11

ELECTRICAL ADJUSTMENT ITEM ADJUSTMENT PROCEDURE VERTICAL POSITION (VCEN) 1. Call up the adjustment mode display, then select item VCEN. 2. Press the VOLUME s or t button to get the voltage +30 ±10 mV. 3. Measuring method of voltage as follows. TP-V (on SIGNAL board) DIGITAL VOLT METER TP-G C (on SIGNAL board) SUB-BRIGHTNESS 1. Constrict the picture height until the (BRTC) vertical retrace line appears adjusting the HEIGHT control on the MAIN board. 2. Adjust the CONTRAST to the minimum and BRIG

Summary of the content on the page No. 12

ITEM ADJUSTMENT PROCEDURE HEIGHT 1. Call up the adjustment mode display, then select the item HIT. (HIT) 2. Press the VOLUME s or t button to get the picture so the top of raster begins to lack. 3. Press the VOLUME s button to advance the data by 10 steps. Note : Check the vertical picture position is correct. WIDTH 1. Call up the adjustment mode display, then select the item WID. (WID) 2. Press the VOLUME s or t button to get the picture so the left and right edges of raster begins to lack. 3.

Summary of the content on the page No. 13

CONVERGENCE ADJUSTMENT Adjust convergence from center to circumference in order. 1. Select the adjustment mode following the steps on page 9. RCUT 40H KEY FUNCTION IN THE CONVERGENCE ADJUSTMENT: Up : 2 button Selet Green color: 3 button Left : 4 button Blinking of cursor ON/OFF: 5 button 2. Press “7” button to display the built-in cross-hatch pattern. Right: 6 button 27.5 Adjust mode ON/OFF: 7 button Down: 8 button Erase Green line: 0 button Erase Red line: 100 button Cursor Erase Blue line: CHR

Summary of the content on the page No. 14

NOTES In many cases, color misconvergence may be corrected by returning HIT and WID data in main deflection side to initial adjusting values. Following cases will surely require readjustment of convergence. CRT REPLACEMENT When CRT is replaced, main deflection readjustment and color matching are required. Perform following procedures. 1. Replace two CRT’s of blue and red. 2. Perform horizontal adjustment for blue and red yokes on base of green CRT data. Mount yoke and velocity mod. coil align- m

Summary of the content on the page No. 15

SCREEN AND MIRROR ALIGNMENTS ASSEMBLING OF MOUNTING OF FRONT SCREEN FRONT SCREEN 5 screws Fresnel sheet 3 screws Protect shield FRONT 3 screws (for 50”) Lenticular sheet 3 screws Protect shield FRONT Fresnel sheet Stick cotton cloth tape Label with part Label with part number number (for 55”, 61”) Lenticular sheet Protect shield Stick contton cloth tape 4 screws FRONT Fresnel sheet Label with part Please refer to Mechanical Disassembly on page 23. Label with part * number number CAUTION : Do

Summary of the content on the page No. 16

CIRCUIT CHECKS HIGH VOLTAGE CHECK FS CIRCUIT CHECK CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on The Fail Safe (FS) circuit check is indispensable for the final this chassis. Checking should be done following check in servicing. Checking should be done following the the steps below. steps below. 1. Connect an accurate high voltage meter to the anode of 1. Turn the receiver on. the picture tube. 2. Temporarily short TP- (R) and TP- (X) on the DEF/POWER 2. Turn on the receiver. Set the BR

Summary of the content on the page No. 17

CHAPTER 2 SPECIFIC INFORMATIONS SETTING & ADJUSTING DATA SAFETY INSTRUCTIONS 43", 50", 55", 61" HIGH VOLTAGE AT ZERO BEAM: (A) 31.3 kV MAX HIGH VOLTAGE: (B) 32.4 kV Table-1 SERVICE MODE ADJUSTING ITEMS AND DATA IN THE SERVICE MODE: Item Name of adjustment Preset Date Item Name of adjustment Preset Date RCUT R CUTOFF 40H ← VCP V-COMPENSATE 0AH ← GCUT G CUTOFF 40H ← PARA E-W PARABOLA (DPC) 29H ← 08H BCUT B CUTOFF 40H ← CNR E-W CORNER ← GDRV G DRIVE 40H ← TRAP TRAPEZIUM 10H ← BDRV B DRIV

Summary of the content on the page No. 18

LOCATION OF CONTROLS (Representative : 50A60) TV front Behind the door CH MENU EXIT TV/VIDEO DEMO AUDIO S-VIDEO VOL VOL POWER VIDEO L/MONO R CH Video Audio inputs POWER VOLUMET S EXIT DEMO MENU CHANNEL st TV/VIDEO TV rear ANT (75Ω) ANT-1 AUDIO CENTER CHANNEL IN OUT ON OFF OUT S-VIDEO R L VAR ANT-2 AUDIO Y VIDEO VIDEO L/ C L B MONO L/ MONO AUDIO AUDIO R C R R R COLOR VIDEO-1 VIDEO-2 STREAM AUDIO INPUT IN DVD IN OUT – 18 – SPECIFIC INFORMATIONS GENERAL ADJUSTMENTS

Summary of the content on the page No. 19

MENU RESET Remote Control LIGHT RECALL LIGHT RECALL POWER POWER TV/CABLE/VCR switch TV MUTE TV/VIDEO TIMER CABLE Set to “TV” to control the TV. TIMER VCR MUTE TV/VIDEO 2 3 1 CHANNEL s/t CH 4 5 6 Channel Number 8 9 7 VOLUME s/t VOL CH RTN 100 0 ENT CH RTN C. CAPT ADV/ PIP CH MENU ENTER PIP CH s FAV t FAV FAV s ENTER FAV s/t/T/S RESET EXIT ADV/ PIP CH t PIP CH STOP SOURCE PLAY PIP PIP functions REC TV/VCR REW FF (For “TV” and “CABLE” modes) STILL LOCATE SWAP – 19 – C.CAPT EXIT SPECIFIC INFORMATION

Summary of the content on the page No. 20

PROGRAMMING CHANNEL MEMORY The channel memory is the list of TV channel numbers the TV tunes in when you press the CHANNEL s or t button. First, use the TV/CABLE and CH PROGRAM functions to preset all active channels in your area automatically. If necessary, arrange the preset channels with the ADD/ERASE functions so that you can tune into only desired channels. Note: If you utilize both ANT-1 and ANT-2 terminals for some model, perform programming channels for each input source. TV/CABLE functi


Alternative user manuals
# User manual Category Download
1 Toshiba 14DL74 User manual Flat Panel Television 358
2 Toshiba 15DL75 User manual Flat Panel Television 70
3 Toshiba 15DLV16 User manual Flat Panel Television 34
4 Toshiba 15CV100U User manual Flat Panel Television 45
5 Toshiba 15DL72 User manual Flat Panel Television 21
6 Toshiba 15DL15 User manual Flat Panel Television 25
7 Toshiba 15VL56G User manual Flat Panel Television 37
8 Toshiba 13A26 User manual Flat Panel Television 43
9 Toshiba 14AF46C User manual Flat Panel Television 20
10 Toshiba 15VL56B User manual Flat Panel Television 20
11 Toshiba 15CV101U User manual Flat Panel Television 18
12 Toshiba 15VL63 User manual Flat Panel Television 27
13 Toshiba 15VL56 User manual Flat Panel Television 8
14 Toshiba 15VL63c User manual Flat Panel Television 14
15 Toshiba 19AV501U User manual Flat Panel Television 32
16 Sony 32LX1E User manual Flat Panel Television 81
17 Sony 4-180-179-16(1) User manual Flat Panel Television 13
18 Sony 4-106-868-11(1) User manual Flat Panel Television 7
19 Sony 32EX52X User manual Flat Panel Television 39
20 Sony 32EX42X User manual Flat Panel Television 24