Summary of the content on the page No. 1
Owner's Manual
®
Liquid Propane Gas Grill
Model 141.152270
Z_ WARNING:
Note to Installer: Leave this Owner's Manual
with the consumer after delivery and/or installation.
Read this Owner's Manual carefully and be sure
your gas grill is properly assembled, installed and
Note to Consumer: Leave this Owner's Manual
maintained. Failure to follow these instructions
in a convenient place for future reference.
could result in serious bodily injury and/or property
damage. This gas grill is intended for o
Summary of the content on the page No. 2
Warranty ..................................................... 2 Z_ WARNI NG Safety Instructions ..................................... 2 Combustion byproducts produced when using this product contain chemicals known to the Pre-Assembly Instructions ......................... 4 State of California to cause cancer, birth defects, or other reproductive harm. Hardware, Parts Diagram and Lists ..... 5 Assembly Instructions ................................. 9 Z_ WARNI NG Lighting Instructions .........
Summary of the content on the page No. 3
18-1/2incheshighis themaximumsizeLPgas • LP gas tanks must be stored outdoors in a well-ventilated area and out of the reach of tankto use.You must usean "OPD"gas tank which offers an OverfillPreventionDevice. children. Disconnected LP gas tanks must not Thissafetyfeatureprevents thetankfrombeing be stored in a building, garage or any other overfilled whichcancausemalfunction of the LP enclosed area. gastank,regulator and/orgrill. • When your gas grill is not in use the gas must be turned off at
Summary of the content on the page No. 4
• Longnoseplierscanbe usedto remove CAUTION: Spiders and small insects occa- CotterPinwhencleaningthe Burners sionally spin webs or make nests in the grill • Useworkglovesto protectyourhands Burner Tubes during transit and warehousing. • Weareyeprotection These webs can lead to a gas flow obstruc- tion which could result in a fire in and around • Whenyouhavefinishedassembling yourGrill besureall PatternHeadThumbScrews the Burner Tubes. This type of fire is known as a "FLASH-BACK" and can cause s
Summary of the content on the page No. 5
The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. Ref. Component Qty. to Use Purpose of Components H019 1/4"x2" Pattern Head Screw 8 Attaches Cart Legs To Bottom Shelf H017 1/4"xl/2" Pattern Head Screw 4 Attaches Tank Pull-Out Tray Kit To Bottom Shelf H017 1/4"xl/2" Pattern Head Screw 4 Attaches Rear Panel To Cart H019 Attaches Door Bracket To Cart 1/4"x2" Pattern Head Screw 4 H017 1/4"xl/2" Pattern Head Sc
Summary of the content on the page No. 6
The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly. Ref. Component Qty. to Use Purpose of Components P55F5A Customized Wrench 1 Tighten Caster P5540B Manual Lighting Stick 1 Attaches To Outside Bowl Panel - Left H025 M4x8mm Pattern Head Screw 1 Attaches To Outside Bowl Panel - Left P55M3A Tightening Tool 1 Allows you to tighten Pattern Head Thumb Screws as needed Each Hardware Piece: Actual Size and Quantity
Summary of the content on the page No. 7
4 1 10\ 57 56 67 19 18 16 23 37 34 26 60 58 21 35 61 4O 47 5O 43 52 53 51 48
Summary of the content on the page No. 8
REF# DESCRIPTION PART# QTY REF# DESCRIPTION PART# QTY 1. Stainless Steel Lid P01AIA 1 46. Rear Panel P4356A 1 47. Door Bracket P4413A 1 2. Lid Side Panel - Left P0164A 1 48. Door Panel P4357A 2 3. Lid Side Panel - Right P0163A 1 49. Door Handle P0271A 2 4. Temperature Gauge P0615D 1 5. Lid Handle P0251A 1 50. Magnetic Door Stop P5589A 2 51. Tank Pull-Out Tray P4043A 1 6. Heat-Insulating Spacer P5573A 2 7. Name Plate P0468A 1 52. Bracket for Tank Pull-Out Tray P4043B 1 53. Slide P55J8A 2 8. Secon
Summary of the content on the page No. 9
Figure 1 CART LEG CAUTION: Whileit ispossible foronepersonto assemble this grill, obtain assistance from another person when handling some of the larger, heavier pieces, espe- cially the grill head. 1. Open Lid of shipping carton and remove top sheet of cardboard. Lay cardboard sheet on floor and use as a work surface to protect floor and grill parts from -RIGHT scratches. 2. Remove packing materials and cart parts from shipping carton. 3. You may slice the carton front corners with a utility kn
Summary of the content on the page No. 10
Install the Door Bracket to the inside of front Figure 4 Cart Legs. Align the threaded holes on the Door Bracket with the holes on Cart Legs. Tighten securely by using 4 of the 1/4"x2" Pattern Head Screws provided. (See Fig. 3. on page 9) Upper door bolt holes (at ends of bracket) must face outward. DOOR BRACKET Installing The Cabinet Doors 1. Install the Door Stops to the Bottom Shelf DOOR and the Door Bracket. See Fig. 4. Found in Hardware Pack Align the holes on the Door Stops with the thread
Summary of the content on the page No. 11
side of Grill Head, install the Grease Draining Figure 7 Traywith its drain hole to left, which is the side opposite from the Tank Pull-Out Tray. GREASE HEAT DRAIN- SHIELD See Fig. 7. ING GRILL TRAY HEAD From the front side of cabinet, open the front \ doors and Install the Grease Receptacle under Grease Draining Tray. See Fig. 7. FRONT DOOR Installing Manual Lighting Stick Attach the Manual Lighting Stick to the Left Bowl Support Bracket as shown in Fig. 8. Align the hole at the end of Manual L
Summary of the content on the page No. 12
end of Side Burner Tube goes over tip of Side Figure 9b POT Burner Valve. Secure Side Burner with supplied SUPPORT Cotter Pin (packed in Side Burner Control Knob \ bag) See Fig. 9b. Place Pot Support into position on Side Burner Frame. SIDE JRNER . Install the Control Knob to the Side Burner Valve Stem. See Fig. 9b. . Connect the Ignition Wire terminal from Side Burner with the other from Grill Head. See Fig. 9b. Bind the connected Ignition Wires and Connection Tube together using the supplied F
Summary of the content on the page No. 13
Ignitor Battery Installation - See Fig. 10 Electrode Check - Requires an Assistant 1. Unscrew the Ignitor Cap located on the grill Before placing the cooking components into your Control Panel and remove the Contact and grill, ensure that the Spark Electrode Tip is properly Spring from the Ignitor Slot. positioned within each Gas Collector Box (a 3-1/4" wide stainless mechanism found at the front 2. Place the manufacturer supplied AA battery between each set of Burners.) The easiest way to into
Summary of the content on the page No. 14
Installing Cooking Components Figure 12 Important: Before cooking on your grill the first time, wash the Cooking Grids and Cooking Rack SECONDARY with warm, soapy water. Rinse and dry thoroughly. COOKING RACK Season with cooking oil regularly. After cooking is completed, turn grill to HIGH setting three to five minutes to burn off excess grease or food residue. 1. Place the two Flame Tamers on the lower COOKING GRID ledge above Burners. See Fig. 12. 2. Evenly space the Cooking Grids (cross brace
Summary of the content on the page No. 15
Disconnecting A Liquid Propane Gas (LP gas) Tank From Your Grill WARNI NG A strong gas smell, or the hissing sound of Turn the Burner Valves and LP gas tank valve gas indicates a serious problem with your gas to the full OFF position. (Turn clockwise to grill or the LP gas tank. Failure to immedi- close.) ately follow the steps below could result in a fire or explosion that could cause serious Detach the hose and regulator assembly from bodily injury, death, or property damage. the LP gas tank v
Summary of the content on the page No. 16
. If the burner does not light, turn the Control Knob to OFF, wait 5 minutes for gas to clear, then retry. 10. Once the left grill burner is ignited, the adjacent Basic Lighting Procedures burner can be lit by simply turning its Control Machine oils used in the manufacturing process of Knob to HIGH. stainless steel can cause stainless steel to turn a tan 11. Adjust Control Knobs to your desired cooking color. Before initial grill use, removing protective PVC film from Control Panel and inside an
Summary of the content on the page No. 17
Misalignment of Ignitor on Burner Manually Lighting Your Grill by Match Correction: Check for proper position of the To light your gas grill by match, insert a match into the Electrode Tip as shown in Figures 9c and 11. Manual Lighting Stick and follow steps 1 through 6 of The gap between the Spark Electrode Tip and the Basic Lighting Procedures. Then, light the match Burner or Spark Receiver should be approxi- and place Manual Lighting Stick through the Lighting mately 3/16", adjust if necessar
Summary of the content on the page No. 18
5. Cover each Gas Valve Orifice with aluminum foil. . Brush the inside and bottom of the grill with a fiber Aswithallappliances, proper careandmaintenance pad or nylon brush, and wash with a mild soap and wiltkeepyourgrillintopoperating condition and warm water solution. Rinse thoroughly and let dry. prolong itslife.Byfollowing these cleaning procedures 7. Remove aluminum foil from Orifices and check onatimelybasis,yourgrillwillstaycleanandwork each Orifice for obstruction. properly withminimum
Summary of the content on the page No. 19
Cleaning The Burner Tubes and Burner Ports Regardless of which Burner cleaning procedure you use, we recommend you also complete the following To reduce the chance of "FLASH-BACK" the proce- steps to help prolong Burner life. dure below should be followed at least once a month in 1. Use a fiber pad or nylon brush to clean the entire late summer or early fall when spiders are most active outer surface of each Burner until free of food or when your grill has not been used for a period of residue a
Summary of the content on the page No. 20
Question: How do l season Cast Iron? Answer: Before and after each cookout, apply a thin layer of cooking oil, spray or vegetable shortening to Question: Can I convert my Kenmore gas grill from each Cooking Grid and optional cast-iron accessory. Be one fuel type to another? sure to coat the entire surface including edges and any Answer: Your Kenmore gas grill is manufactured to areas with chipped porcelain. Insert the Cooking Grids exact specifications and is approved by the Canadian and accesso
