Summary of the content on the page No. 1
FOR OUTDOOR USE ONLY
Stainless Steel Gas Grill
USE AND CARE GUIDE
MODEL NO.: 720-0430
400 500 600
30 0
70 0
20 0 80 0
10 0
Consumer: Retain this manual for future reference.
D20Y07P_1
Installer: Leave this manual with consumer
PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE
ABOUT ASSEMBLY OR GRILL OPERATION
DO NOT RETURN TO THE PLACE OF PURCHASE
Summary of the content on the page No. 2
TABLE OF CONTENTS SECTION ONE SECTION FOUR Table of content / important ………………...........1 Op erating Instructions………………………… .16 Precautions……………………………… ……....2-5 Lighting I nstructions…………………….......16-18 To match light the grill ………………………….19 SECTION TWO Lighting Illustration………………………………20 Side burner control panel assembly………………6 Side Shelf wooden mount panel assembly …….7 SECTION FIVE Side shelf push
Summary of the content on the page No. 3
PRECAUTIONS WARNING CAUTION: Beware of Flashback Do not try lighting this appliance without reading the “LIGHTING INSTRUCTIONS” section of this manual. CAUTION: Spiders and small insects occasionally spin webs or make nests in the grill burner tubes during transit and warehousing. These webs can lead TESTED IN ACCORDANCE WITH ANSI to gas flow obstruction, which could result in a fire in Z21.58b CSA 1.6b-2006 STANDARD FOR and around burner tubes. This type of fire is known as “FLASH-BACK”
Summary of the content on the page No. 4
Section One PRECAUTION LP-Gas Supply System PROPER PLACEMENT AND CLEARANCE OF GRILL A 20lbs tank of approximately 1/4 inches in diameter by 18-1/4 •Never use your gas grill in a garage, porch, shed, inches high is the maximum size LP gas tank to use. breezeway or any other enclosed area. Your gas grill This safety feature prevents the tank from being overfilled, which is to be used outdoors only. can cause malfunction of the LP gas tank, regulator and/or grill. •Do Not install this uni
Summary of the content on the page No. 5
PRECAUTIONS SAFETY PRACTICES TO AVOID PERSONAL WARNING INJURY Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch When properly cared for, your grill will provide cooking surfaces, grill housing, lid or any other safe, reliable service for many years. However, grill parts while the grill is in operation, or until the extreme care must be used as the grill produces gas grill has cooled down after use. intense heat that can increase accident
Summary of the content on the page No. 6
PRECAUTIONS Do not heat unopened food containers. A build-up Do not use the grill to cook excessively fatty meats of pressure may cause the containers to burst. or other products which promote flare – ups. Use a covered hand when opening the grill lid. Do not operate the grill under unprotected combustible constructions. Use only in well Never lean over an open grill. ventilated areas. Do not use in buildings, garages, sheds, breezeways or other such enclosed areas. When lighting a burner,
Summary of the content on the page No. 7
Section Two SIDE BUENER CONTROL PANEL ASSEMBLY Loosen the three screws and washers from side burner bowl, then attach side burner with control panel and tighten them as in the figure shown below. Finally attach the side burner flex wire to the side burner by using a wrench (included). SIDE SHELF ASSEMBLY The screws used to attach the side shelf are already screwed into the left side shelf and side burner (see the figure below). First remove the screws from the left side shelf and side burner b
Summary of the content on the page No. 8
SIDE SHELF WOODEN MOUNT PANEL ASSEMBLY Attach side shelf wooden mount panel after remove 4 screws from it. 400 50 0 60 0 30 0 700 200 800 10 0 USING STEPS: 1.Use two fingers to press the hinge which is under the wooden control panel (see below pix 1). 2. Pull up the panel to the lever same as side shelf by hands. See pix 2. 3. To put panel down reverse order steps one and two above. CAUTION: To avoid the injury, never let children play with this operation. CAUTION: Never put your hands on th
Summary of the content on the page No. 9
SIDE SHELF PUSH BAR ASSEMBLY Required tools: Philips Screwdriver (not included) 1. Remove the four side handle screws from the side of the shelf. 2. Align the holes in the side shelf handle with the holes in the shelf. 3. Insert the fix pieces and the screws then tighten them. 400 500 600 30 0 70 0 80 0 20 0 10 0 SIDE BURNER ASSEMBLY 1. Insert valve venturi into the side burner and tighten securely using an adjustable wrench. 500 400 60 0 300 70 0 80 0 20 0 10 0 8
Summary of the content on the page No. 10
2. Connect ignite wire with side valve. 40 0 500 600 300 700 200 100 80 0 REAR BURNER IGNITER WIRE ASSEMBLY Connect the rear burner igniter wire into the electric igniter. 30 0 400 50 0 200 60 0 10 0 80 0 70 0 9
Summary of the content on the page No. 11
SIDE BURNER LID BrACKET ASSEMBLY First remove the screws from side burner lid. Then attach side burner bracket with side burner frame as shown below from top to bottom with three washers and screws. 50 0 40 0 600 30 0 700 200 800 100 10
Summary of the content on the page No. 12
BATTERY ASSEMBLY In order to install the battery, remove the ignition button housing. Please keep the positive pole of the battery facing toward you. Insert the battery into the housing. Replace the ignition button housing after battery is installed. 400 500 600 300 700 200 100 800 ROTISSERIE KIT ASSEMBLY Screw the rotisserie motor mount on the left side shelf first, put the rotisserie motor on the mount as shown in the figure below. Assemble the rotisserie skewer as shown in the figure belo
Summary of the content on the page No. 13
C L O S E PROPANE TANK ASSEMBLY Attach regulator to the propane tank by turning the regulator handle clockwise (FIGURE A). Turn off LP supply at cylinder when appliance is not in use. g (FIGURE A) Put the gas tank into bottom panel. Then tighten up the gas tank retention kit for fixing the gas tank as shown in below. 400 50 0 600 30 0 700 200 100 800 12 O P E N
Summary of the content on the page No. 14
Section Three GAS HOOK UP NEVER CONNECT AN UNREGULATED QCC1 in the standard for compressed gas GAS SUPPLY LINE TO THE APPLIANCE. cylinder valve outlet and inlet connection USE THE REGULATOR/HOSE ANSI/CGA-V-1. ASSEMBLY SUPPLIED. Manifold pressure: 10”(25.4cm) water This is a liquid propane configured grill. column (W.C.). Do not attempt to use a natural gas supply L.P. GAS HOOK-UP unless the grill has been reconfigured for natural gas use. Ensure that the rubber “O” Ring on the LP cylinder
Summary of the content on the page No. 15
GAS HOOK-UP To disconnect L.P. gas cylinder: 5. When connecting regulator assembly to the valve, hand tighten the quick coupling nut clockwise to 1. Turn the burner valves off. a complete stop. Do not use a wrench to tighten. 2. Turn the tank valve off fully (turn clockwise to Use of a wrench may damage the quick stop). coupling nut and result in a hazardous condition. 3. Detach the regulator assembly from the tank 6. Open the tank valve fully (counterclockwise). valve by turning the qui
Summary of the content on the page No. 16
LEAK TESTING GENERAL Only those parts recommended by the manufacturer should be used on the grill. Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete Substitution will void the warranty. Do not use the gas tightness check must be performed at the grill until all connections have been checked and installation site due to possible mishandling in do not leak. shipment, or excessive pressure unknowingly being applied to the unit. Periodica
Summary of the content on the page No. 17
Section Four OPERATING INSTRUCTIONS CAUTION: PLEASE TAKE OFF THE WARMING RACK WHEN USING THE ROTIS BURNER. THE HIGH HEAT COMING FROM THE ROTIS BURNER MAY CAUSE THE WARMING RACK TO BEND. GRILL LIGHTING INSTRUCTIONS Never substitute regulators and hose assembly WARNING: IMPORTANT! for those supplied with the grill. If a replacement BEFORE LIGHTING… is necessary, contact the manufacture for proper replacement. The replacement must be that Inspect the gas supply hose prior to turning the g
Summary of the content on the page No. 18
GRILL LIGHTING INSTRUCTIONS If you’ve just attempted to light the burner with the TO LIGHT THE GRILL BURNER: igniter, allow 5 minutes for any accumulated gas to Make sure all knobs are “OFF” then turn on the gas dissipate. Keep your face and hands as far away supply from the LP tank. Always keep your face and from the grill as possible. Insert a lit match attached body as far from the grill as possible when lighting. to the lighting rod through the cooking grids to the burner.(see next pa
Summary of the content on the page No. 19
TO MATCH LIGHT THE GRILL 1. If the burner will not light after several attempts then the burner can be match lit. 2. If you’ve just attempted to light the burner with the igniter, allow 5 minutes for any accumulated gas to dissipate. Keep your face and hands as far away from the grill as possible. Insert a lit extended match or lighter through the cooking grids to the burner. Press the control knob and rotate left to the HI setting, continue to press the knob until the burner ignites. Burner
Summary of the content on the page No. 20
GRILL LIGHTING INSTRUCTIONS flame is noisy and tends to lift away from FLAME CHARACTERISTICS the burner, it indicates too much air. Check for proper burner flame characteristics. Burner flames should be blue and stable Each burner is adjusted prior to with no yellow tips, excessive noise, or shipment; however, variations in the lifting. If any of these conditions exist call local gas supply may make minor our customer service line. If the flame is adjustments necessary. yellow, it indicate
