Summary of the content on the page No. 1
B
E
W
R
E
® ®
®
®
GENESIS SILVER–A
GENESIS SILVER–A
Gas Grill
Owners Guide
DANGER
If you smell gas:
1. Shut off gas to the appliance.
Liquid Propane Gas
2. Extinguish any open flames.
3. Open lid
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
WARNING
1. Do not store spare liquid propane
cylinder within 10 feet (3m
Summary of the content on the page No. 2
DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. WARNINGS Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas le
Summary of the content on the page No. 3
Warranty Weber-Stephen Products Co. (Weber) hereby There are no other express warrants except as set warrants to the ORIGINAL PURCHASER of this forth herein and any applicable implied warranties of Weber Gas Grill that it will be free of defects in merchantability and fitness are limited in duration to material and workmanship from the date of purchase the period of coverage of this express written Limited as follows: Warranty. Some regions do not allow limitation on how long an implied warranty
Summary of the content on the page No. 4
Contents Danger & Warnings ................................ A-2 Warranty ................................................. A-3 General Instructions ............................... A-5 Exploded View ........................................ A-6 Parts List ................................................ A-9 Assembly Instructions ............................ B-1 Installing Features .................................. C-1 Operating ............................................... D-1 Lighting.........
Summary of the content on the page No. 5
Storage General Instructions • The gas must be turned OFF at the LP cylinder Your Weber Gas Barbecue is a portable outdoor when the Weber Gas Barbecue is not in use. cooking appliance. With the Weber Gas Barbecue you • When the Weber Gas Barbecue is stored indoors, can grill, barbecue, roast and bake with results that are the gas supply must be disconnected and the LP difficult to duplicate with indoor kitchen appliances. cylinder stored outdoors in a well-ventilated space. The closed lid and Fl
Summary of the content on the page No. 6
1 2 Genesis Silver-A LP 3 4 25 5 26 6 7 8 27 28 9 29 30 31 10 32 11 33 12 34 13 35 36 14 37 15 38 39 16 30 17 40 18 41 19 42 43 20 44 21 45 46 22 23 24 47 48 A-6 49
Summary of the content on the page No. 7
1. Hair Pin Cotter 25. Thermometer 2. Hinge Pin 26. Right Endcap 3. Left Endcap 27. Burner Control Knobs 4. Shroud 28. Control Panel 5. Handle 29. Ignitor Button 6. Warming Rack 30. Control Panel Hardware 7. Cooking Grates 31. Crossover tube 8. Flavorizer Bars 32. Back Burner 9. Cooking Box 33. Manifold Hardware 10. 1/4-20 keps nut 34. Manifold, Hose and regulator (assembled) 11. Slide Out Bottom Tray 35. Manifold Support Bracket 12. Catch pan holder 36. Spider Stopper Guards 13. Left Trim Piece
Summary of the content on the page No. 8
© 1999 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks ® of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A. A-8
Summary of the content on the page No. 9
® ® ® ® ® You will need: Bottom tray - 1 Screwdriver Phillips screwdriver Hammer Left Frame - 1 7/16 open-end or an adjustable wrench Right Frame -1 Pliers Block of wood Wheel Frame - 1 Lid - 1 Leg Frame - 1 Frame Connectors - 1 Cooking Box - 1 Work Surface - 1 Left trim piece - 1 Right Trim Piece - 1 Cooking grates - 2 Bottom Shelf - 1 Control panel - 1 A-9
Summary of the content on the page No. 10
Warming Rack - 1 Manifold Support Bracket - 1 Flavorizer Bars - 5 Burner Control Knobs - 2 Cylinder Panel - 1 Hinge Pins (1/4 x 1 1/2 inch clevis pin) - 2 2 inch bolts (1/4 x 20 x 2 inch bolts) - 1 Wrap-Around Trim Piece - 1 1 3/4 inch bolts (1/4 x 20 x 1 3/4 inch bolts) - 4 1/2 inch bolts (1/4 x 20 x 1/2 inch bolts) - 8 Catch Pan Holder - 1 Keps Nut (1/4 x 20 Keps Nut) - 1 Catch-Pan - 1 Wing Nut (1/4 x 20 Wing Nut) - 2 Disposable Drip Pans - 2 Nylon Washers - 13 Thermometer - 1 Hair Pin Cotter
Summary of the content on the page No. 11
R E B E W Assembly Instructions Assemble wheel frame Assemble frame You will need: axle rod, two wheel hubcaps, two You will need: left frame, right frame, two 1/2 inch wheels, wheel frame, hammer and a block of wood. bolts, two nylon washers and a 7/16 inch or adjustable Place one end of the axle rod on the block of wood (or wrench. other protected surface). Tap one hubcap onto the end Note - Work on carpeted area (on grass or one of the of the axle rod. Slide one wheel onto the axle, WEBER box
Summary of the content on the page No. 12
Continue frame assembly Add Wrap-around Frame Panel You will need: leg frame, wheel frame, four 1/2 inch You will need: wrap around frame panel and a wrench. bolts, four nylon washers and a 7/16 inch or adjustable Place wrap-around frame panel in place: wrench. 1) The cut-out tabs should fit between the washer Place the leg frame onto the tabs of the left frame. and the frame, as shown. Place the wheel frame onto the tabs of the right frame. 2) The square cut-out holes fit around the white plugs
Summary of the content on the page No. 13
Add cooking box (assembly) Your Weber Gas Grill manifold assembly, consisting of You will need: frame assembly, cooking box (assem- gas manifold, valves, hose, regulator and gas burners bly), 2 inch bolt, nylon washer, keps nut, pliers and a 7/ has been factory assembled, pressure and flame 16 inch or adjustable wrench. tested. As a safety precaution, we recommend you Uncoil the hose. check the burner alignment: Place the cooking box (assembly) in the frame assem- 1) Are the ends of the burners
Summary of the content on the page No. 14
Install manifold bracket Install cylinder panel and frame connector You will need: manifold bracket. You will need: cylinder panel, frame connector, four 1 Hook the bracket(2) onto the manifold in the center. 3/4 inch bolts, four nylon washers, two cylinder glides a Place your hand underneath the bracket. Lift the 7/16 inch or adjustable wrench and pliers. manifold, bracket and cooking box slightly, then hook Insert the cylinder panel tabs(1) into the slots in the the tab of the bracket onto the
Summary of the content on the page No. 15
Add fuel gauge Install igniter You will need: fuel gauge, two wing nuts and two nylon Note - The igniter wires are already attached to the washers. Gas Catcher Ignition Chamber and the igniter. This 1) Slip the bolts on the back of the fuel gauge was done to factory test the ignition system. through the two small holes in the cylinder panel. The igniter lock nut is on the igniter. 2) Add washers to the bolts, then wing nuts, and 1) Loosen the igniter lock nut. tighten with your fingers. 2) Inser
Summary of the content on the page No. 16
Fill liquid propane cylinder Check that all burner valves are off Note - The liquid propane cylinder manufacturer is You will need: burner control knobs. responsible for the materials, workmanship and Valves are shipped in the OFF position, but you should performance of the cylinder. If the cylinder has a check to be sure that they are turned OFF. Put the defect, malfunctions, or you have a question regarding knob on each valve. Check by pushing down and the cylinder, call the cylinder manufactu
Summary of the content on the page No. 17
Screw the regulator coupling onto the cylinder Check for gas leaks valve(1), clockwise, or to the right. Hand tighten only. DANGER Note: This is a new type of connection. It tightens Do not use an open flame to check for gas clockwise and will not allow gas to flow unless the leaks. Be sure there are no sparks or open connection is tight. The connection requires tightening flames in the area while you check for by hand only. WARNING: Do not use a wrench to tighten the leaks. Sparks or open f
Summary of the content on the page No. 18
Check: Install the slide out bottom tray 1) Hose to manifold connection. You will need: the slide out bottom tray(1), catch pan 2) Regulator to cylinder connection. holder(2), catch pan and one disposable drip pan. WARNING: : If there is a leak at connection (1) , retighten the fitting with a wrench and recheck for leaks with soap and water solution. If a leak persists after retightening the fitting, turn OFF the gas. DO NOT OPERATE THE BARBECUE. Contact the Customer Service Representative in
Summary of the content on the page No. 19
Install Lid Install control panel and burner control knobs You will need: lid, two hair pin cotters(1) and two hinge You will need: control panel, two Phillips screws/ pins(2). washers, a Phillips screwdriver, and burner control Place lid on top of the cooking box. Align the hinges at knobs. the rear of the barbecue. Insert hinge pins through the 1) Set the control panel in place over both frame hinges from the outside. Insert hair pin cotters into the braces. Hold the Crossover Ignition button
Summary of the content on the page No. 20
Installing Features Install the right trim piece with tool holders Install the work surface You will need: Right trim piece with tool holders You will need: work surface. Push the Right trim piece into the frame as shown(1), Place the work surface, so that the front and back making sure that the tabs on the underside of the trim edges fit over the frame, in the area between the left piece are snapped into the slots in the frame.(2) trim piece and the cooking box as shown. Do not use the work sur
