Summary of the content on the page No. 1
R
E
B
E
W
®
®
GENESIS SILVER–C
GENESIS SILVER–C
Gas Grill
Owners Guide
DANGER
If you smell gas:
1. Shut off gas to the appliance.
Natural Gas
2. Extinguish any open flames.
3. Open lid
4. If odor continues, keep away from the
appliance and immediately call your
®®
gas supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
WARNING
Do not store or use gasoline or other
flammable liquids or vapors within
Summary of the content on the page No. 2
DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. WARNINGS Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas le
Summary of the content on the page No. 3
Warranty Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Grill There are no other express warrants except as set forth that it will be free of defects in material and herein and any applicable implied warranties of workmanship from the date of purchase as follows: merchantability and fitness are limited in duration to the period of coverage of this express written Limited Aluminum Castings, lifetime, 1 year paint Warranty. Some regions do not allow
Summary of the content on the page No. 4
Contents Danger & Warnings ................................ A-2 Warranty ................................................. A-3 General Instructions ............................... A-5 Exploded View ........................................ A-6 Parts List ................................................ A-9 Assembly Instructions ............................ B-1 Installing Features .................................. C-1 Operating ............................................... D-1 Lighting.........
Summary of the content on the page No. 5
Storage General Instructions • The gas must be turned OFF at the natural gas Your Weber Gas Barbecue is a portable outdoor supply when the Weber Gas Barbecue is not in cooking appliance. With the Weber Gas Barbecue you use. can grill, barbecue, roast and bake with results that are • When the Weber Gas Barbecue is stored indoors, difficult to duplicate with indoor kitchen appliances. The the gas supply must be disconnected. closed lid and Flavorizer® Bars produce that “outdoor” flavor in the food
Summary of the content on the page No. 6
Genesis Silver-C NG 1 2 27 3 28 4 29 5 30 31 6 32 33 7 8 34 9 35 10 36 11 37 12 38 13 39 40 14 41 42 15 43 16 44 45 17 46 18 33 19 47 18 20 48 21 49 22 23 50 24 51 25 52 26 A-6
Summary of the content on the page No. 7
1. Hinge Pin 27. Hair Pin Cotter 2. Left Endcap 28. Thermometer 3. Shroud 29. Right Endcap 4. Handle 30. Burner Control Knobs 5. Warm-Up Basket 31. Control Panel 6. Warming Rack 32. Ignitor Button 7. Cooking Grates 33. Control Panel Hardware 8. Flavorizer Bars 34. Side Burner 9. Cooking Box 35. Crossover tube 10. 1/4-20 keps nut 36. Front and Back Burners 11. Slide Out Bottom Tray 37. Center Burner 12. Catch pan holder 38. Manifold Hardware 13. Catch pan 39. Manifold 14. Left Frame 40. Manifold
Summary of the content on the page No. 8
© 1999 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks ® of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A. A-8
Summary of the content on the page No. 9
® ® ® ® ® Screwdriver Left Frame - 1 Phillips screwdriver Hammer Right Frame - 1 7/16 open-end or an adjustable wrench Wheel Frame - 1 Pliers Caster Frame - 1 Block of wood Lid - 1 Frame Connectors - 2 Left Trim Piece - 1 Right Trim Piece - 1 Cooking Box - 1 Work Surface - 1 Left Swing-Up Work Surface - 1 Cooking grates - 2 Right Swing-Up Work Surface Hinge Rod - 2 Control panel - 1 Bottom Shelf - 1 Wheel Axle - 1 A-9
Summary of the content on the page No. 10
Warming Rack - 1 Manifold Support Bracket - 1 Warm-Up Basket - 1 Burner Control Knobs - 3 Flavorizer Bars - 5 Hinge Pins (1/4 x 1 1/2 inch clevis pin) - 2 Front Panel - 1 2 inch bolts (1/4 x 20 x 2 inch bolts) - 5 Back Panel - 1 1/2 inch bolts (1/4 x 20 x 1/2 inch bolts) - 8 Bottom tray - 1 Keps Nut (1/4 x 20 Keps Nut) - 1 Nylon Washers - 13 Catch Pan Holder - 1 Cotter Pin - 2 Hubcaps - 3 Catch-Pan - 1 Control Panel Hardware (Phillips screws/washers) - 2 Disposable Drip Pans - 2 Hose - 1 Thermom
Summary of the content on the page No. 11
R E B E W Assembly Instructions Assemble wheel frame Assemble frame You will need: axle rod, two wheel hubcaps, two You will need: left frame, right frame, two 1/2 inch wheels, wheel frame, hammer and a block of wood. bolts, two nylon washers and a 7/16 inch or adjustable Place one end of the axle rod on the block of wood (or wrench. other protected surface). Tap one hubcap onto the end Note - Work on carpeted area (on grass or one of the of the axle rod. Slide one wheel onto the axle, WEBER box
Summary of the content on the page No. 12
Continue frame assembly Add back panel You will need: caster frame and wheel frame. You will need: frame assembly, back panel, two 1/2 Place the caster frame onto the tabs of the left frame, inch bolts, two nylon washers, and a 7/16 or adjustable so that the swing table locking bracket (1) is to the rear. wrench. Place the wheel frame onto the tabs of the right frame, Place the back panel against the inside frame assem- so that the swing table locking bracket is to the rear bly as shown in illus
Summary of the content on the page No. 13
Insert casters Slide the cooking box (assembly) to the left within the You will need: frame assembly and two casters. frame assembly. Add the nylon washer to the bolt. Push the casters firmly into the inserts in the ends of Insert the bolt through the cooking box and frame with the caster frame. the head of the bolt outside the box. Add the keps nut. Tighten by holding the bolt with pliers while you tighten the nut with a wrench. Add cooking box (assembly) You will need: frame assembly, cooking
Summary of the content on the page No. 14
Your Weber Gas Grill Manifold assembly consisting of Install Gas Supply gas manifold, valves and gas burners has been factory General Specifications for Piping assembled, pressure- and flame- tested. As a safety Note - Contact your local municipality for building precaution, we recommend you check the burner codes regulating outdoor gas barbecue installa- alignment: tions. In absence of Local Codes, you must con- 1) Are the ends of the burners under the washers at firm to the latest edition of A
Summary of the content on the page No. 15
Gas Line Piping Install igniter If the length of the line required does not exceed 50 Note - The igniter wires are already attached to the feet, use a 5/8" O.D. tube. One size larger should be Gas Catcher Ignition Chamber and the igniter. This used for lengths greater than 50 feet. was done to factory test the ignition system. Gas piping may be copper tubing, type K or L; The igniter lock nut is on the igniter. polyethylene plastic tube, with a minimum wall thick- 1) Loosen the igniter lock
Summary of the content on the page No. 16
Check that all burner valves are off Connect flexible hose to manifold You will need: burner control knobs. You will need: the 12 foot natural supply hose and a 3/ Valves are shipped in the OFF position, but you should 4 inch wrench. check to be sure that they are turned OFF. Put the Thread fitting end of hose onto manifold. Tighten with knob on each valve. Check by pushing down and wrench. turning clockwise. If they do not turn, they are off. Proceed to the next step. If they do turn continue t
Summary of the content on the page No. 17
Install the slide out bottom tray Slide the bottom tray onto the mounting rails under the You will need: the slide out bottom tray(1), catch pan cooking box with finger grip toward you(1). holder(2), catch pan and one disposable drip pan. WARNING: Do not line bottom tray with alumi- num foil. It can cause grease fires by trapping the grease and not allowing grease to flow into the catch pan. (1) (2) Hook the ends of the catch pan holder into the hole in the slide out bottom tray. The front of
Summary of the content on the page No. 18
Install Lid Install control panel and burner control knobs You will need: lid, two hair pin cotters(1) and two hinge You will need: control panel, two Phillips screws/ pins(2). washers, a Phillips screwdriver, and burner control Place lid on top of the cooking box. Align the hinges at knobs. the rear of the barbecue. Insert hinge pins through the 1) Set the control panel in place over both frame hinges from the outside. Insert hair pin cotters into the braces. Hold the Crossover Ignition button
Summary of the content on the page No. 19
Installing Features Install the right end trim piece with tool holders 3.) Insert one end of the swing-up work surface rod and right swing-up work surface into the hole in the frame. You will need: Right trim piece with tool holders, right swing-up work surface, swing-up work surface rod, one 1/2 inch bolt, one nylon washer and a wrench 1.) Start the right end trim piece into the frame as shown, do not push the trim piece in all of the way and do not add bolt yet. (1) 2.) Slide the swing-up work
Summary of the content on the page No. 20
4.) While holding swing-up work surface in position, To raise swing-up work surface: Lift table all the way up insert the other end of the swing-up work surface and slide it to the left, then lower table until you feel it rod into the right end trim piece (1). Push the trim lock in the up position. piece into the frame as shown, making sure that the tab on the back underside piece of the trim To lower swing-up work surface: Lift table up until it piece is snapped into the slot in the rear frame
