Summary of the content on the page No. 1
LP Gas Grill Assembly and Use Manual
With the NEW Aussie
FLAVOR ACTIVATOR SYSTEM
(Patent Pending)
Provides:
- More even heat on the cooking surface
- Hotter temperature with the same fuel usage
- Longer cooking for the same amount of fuel
68R5A9SSS1
For Outdoor Household Use Only. Not for Commercial Use.
Need Help? Need to Register Your Grill? Looking for Aussie Parts & Accessories?
Visit us online at www.AussieGrills.com Or call Aussie Customer Service at 1-800-251-7558
WARNING DANGER
! !
• Fai
Summary of the content on the page No. 2
2 NOTICE Meco Corporation strives to be a quality supplier of consumer products. If we omitted any parts needed for assembly, or you need troubleshooting information, please contact us using our toll free number or visit our web site. It is important to register your grill and retain your receipt. 1-800-251-7558 Consumer Service Department 8 am - 5 pm E.S.T. Monday - Friday MECO CORPORATION 1-423-639-1171 (Telephone) 1500 Industrial Road 1-423-639-2570 (Fax) Greeneville, TN 37745 USA www.aus
Summary of the content on the page No. 3
3 Packing List Description Warming Rack Cooking Grid, 3 pcs. Flavor Activators - 4 large, 3 small Grease Pan Foil Pan Left Side Shelf with Side Burner Side Burner Control Knob Hood/Body Right Side Shelf Bottom Body Panel Cabinet Back Panel Front Crossbar 3 Drawer Tracks, 2 pcs. Cabinet Side Panel- Left Back Panel Brace wire Cylinder Retainer Bolt Cabinet Upright Cylinder Blocking Wire Cabinet Side Panel- Right Cabinet Bottom Panel Front Corner Brackets Drawer Body Locking Caster, 2 pcs. Fixed
Summary of the content on the page No. 4
4 Contents Packing List .................................................................. 3 Before Using Your Grill Installation Codes .......................................................18 Preparation for Assembly ..........................................4 Selecting a Location ...................................................18 Assembly Instructions Performing a Leak Test ...............................................18 Step 1 Caster Assembly ............................................
Summary of the content on the page No. 5
5 Assembly Instructions Step 1 Caster Assembly Lay Cabinet Bottom Panel upside down, so that the flat surface is on the floor. Assemble Fixed Casters to the LEFT Side (the side closest to the cutouts) of Cabinet Bottom Panel and Swivel Lock Casters to the RIGHT Side of Cabinet Bottom Panel. Insert 1/4-20 x .60” Bolts through the caster bracket holes into the threaded holes in the Cabinet Bottom Panel. Tighten the bolts. Push the lever on the two Locking Casters to lock so the caster wheels do
Summary of the content on the page No. 6
6 7 Step 3 Side Panel Assembly Attach Left Side Panel and Right Side Panel to Cabinet Bottom Panel with six 1/4-20 x .50” Bolts and 1/4-20 Nuts. 1/4-20 x .50” Bolt set 6 pc Secure Left and Right Side Panels to Back Panel with four 5/32 x .31” Bolts through the inside of the Back Panel. 5/32 x .31” Bolt set 4 pc
Summary of the content on the page No. 7
7 Step 4 Front Crossbar Assembly Turn cart assembly up on casters. Attach Front Crossbar, with the triangle braces facing down and the flat surface to the front, to Side Panels with six 1/4-20 x .50” Bolts into the threaded holes in the top inside ends of Side Panels. front crossbar 1/4-20 x .50” Bolt set 6 pc Step 5 A. Cabinet Upright Assembly Attach Cabinet Upright to Cabinet Bottom and Front Crossbar with four 5/32 x .31” Bolts. Orient Upright so that Match holder/Chain is closest to top o
Summary of the content on the page No. 8
8 WARNING ! To reduce the risk of serious bodily injury or death from fire or explosion: • Never remove guards or devices to prevent storage of spare or oversize LP Gas Cylinders not recommended for this grill. Step 6 A. Back Panel Brace wire Assembly Attach Back Panel Brace wire to Front Crossbar and Back Panel with two 5/32 x .47” Bolts. B. Cylinder Blocking Wire Assembly Attach Cylinder Blocking Wire to Right Side Panel with one 5/32 x .47” Bolt and nut. Attach to Bottom Panel with one 5/32
Summary of the content on the page No. 9
9 Step 8 Model 6805 & 6804 with drawer Drawer Track Assembly and Cylinder Retaining Bolt Installation A. Attach one Drawer Track to Back Panel and Cabinet Upright using four 5/32 x .31” Bolts. Attach other Drawer Track to Back Panel and Right Side Panel using four 5/32 x .31” Bolts. B. Install the Cylinder Retainer Bolt through the hole in the back of the Bottom Shelf into the nut welded underneath. A 5/32 x .31” Bolt set 8 pc B Cylinder Retainer Bolt Step 9 Model 6805 & 6804 with drawer
Summary of the content on the page No. 10
10 Step 10 Door Assembly Install LEFT Door. Drop bottom door pin into Cabinet Bottom Panel hole. Swing top of door toward hole in top of Left Side Panel. Depress spring-loaded pin with thumb while sliding pin into Left Side Panel hole until it snaps into place. Right Door assembly is similar; Fixed pin is under drawer and inserts into hole in door and spring-loaded pin is in the BOTTOM of small door and functions the same. Depress Left Door shown, Right Door under drawer. CAUTION ! To reduc
Summary of the content on the page No. 11
11 CAUTION ! Prior to performing any further assembly, PERFORM “FIRST TIME USE” LEAK TEST as detailed on pages 19-20. If the grill is fully assembled before performing the First Time Use leak test, the side tables will need to be removed in order to perform the leak test on the main burner valves inside the control panel, behind the knobs, . Step 12 Side Table Assembly A. Screw two 1/4-20 x .50” Bolts into the two bottom threaded inserts on the outside of the Bowl. Do not screw Bolts all the
Summary of the content on the page No. 12
12 Step 13 Side Burner Valve Assembly NOTE: Side Burner Valve is already attached to the regulator hose. Hose is not shown in some illustrations for clarity. A. Install the Side Burner Valve from underneath the LEFT Side Table. Remove the screws from the side burner bracket and set aside with bracket. B. Tilt venturi end of burner down and slide rectangular venturi windscreen toward back of grill to expose open end of burner tube. C. Insert the valve stem out through the hole in the bezel and
Summary of the content on the page No. 13
13 CAUTION ! To avoid possible damage to grill, DO NOT ATTEMPT TO LIFT GRILL BY THE SIDE TABLES Step 15 A. Side Burner Control Knob Assembly Align the flat keyed hole in the Control Knob with the keyed stem of the Side Burner Valve. Push the Control Knob onto the Side Burner Valve stem. B. Side Burner Grid Assembly Place the Side Burner Grid onto Side Burner Table, allowing the three protruded ends to fall into the three holes around the Side Burner. A B Step 16 A. Bottom Body Panel Assembly
Summary of the content on the page No. 14
14 CAUTION ! To reduce the risk of a laceration hazard: • Wear protective gloves when installing warming rack. Hood and Bowl edges could be sharp. Step 17 Warming Rack Assembly Insert Warming Rack leg ends into holes on top edge of firebox. Seat securely. Step 18 Flavor Activator/Cooking Grid Assembly A. Lay a large Flavor Activator over each Tube Burner on the lower body ridges. Lay a small Flavor Activator between each large Flavor Activator. Each Flavor Activator has individual guides on th
Summary of the content on the page No. 15
15 Step 19 Battery in Igniter Installation Unscrew Igniter Cover and insert AA Battery with the negative “-“ end going in first. Replace the cover and tighten securely. Battery AA 1.5v Alkaline 1 pc - + This Completes the Grill Assembly. Storage WARNING ! To reduce the risk of serious bodily injury or death: • Store your LP gas grill in a cool dry place. Do not store an LP Gas Cylinder in a space greater than 125 degrees Fahrenheit. Never store a connected LP Gas Cylinder in a building, garage
Summary of the content on the page No. 16
16 Connecting/Disconnecting the Gas Using Gas DANGER ! Carbon Monoxide Hazard • This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. • Never use this appliance indoors, on recreational vehicles, or boats. WARNING ! To reduce the risk of serious bodily injury or death from fire or explosion: • Use only propane gas with this LP gas grill. • Do not attempt to convert an LP unit to natural gas. • Always use a gas appliance outdoors in an open area
Summary of the content on the page No. 17
17 LP Hose and Regulator WARNING ! To reduce the risk of serious bodily injury or death NOTE: from fire or explosion: If the hose/regulator assembly is not working properly • Clean and inspect the gas hose/regulator before and you need a replacement, contact Customer Service each use of the outdoor cooking gas appliance. at 1-800-251-7558 or go to www.aussiegrills.com. The gas hose/regulator must be replaced prior to being used, if there is evidence of excessive abra- Be sure to have the g
Summary of the content on the page No. 18
18 Before Using Your LP Gas Grill Installation Codes WARNING ! To reduce the risk of serious bodily injury or death from fire or explosion: • This installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54 Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B149.2 or the Standard for Recreational Vehicles, ANSI A 119.2/NFPA 1192 and CSA Z240 RV Series, recreational Vehicle C
Summary of the content on the page No. 19
19 CAUTION ! To reduce the risk of a laceration hazard: • Wear protective gloves when removing or replacing Control panel, which could have sharp edges. How to Perform A Leak Test “FIRST TIME USE” and as required Supplies Needed for a Leak Test: • Clean paint brush • Water • Dish washing liquid 1. Use an LP Gas Cylinder equipped with an OPD (Overfill Prevention Device) and have it filled at an authorized LP gas dealer by a qualified attendant. 2. Make sure all grill Control Panel Knobs are turn
Summary of the content on the page No. 20
20 6. Check for leaks by brushing the soap solution on all gas valves, hose connections and fittings. (Shown by the heavy arrows in Fig. 3a, 4, 5 and 6a) Make sure you generously brush the locations with the soap solution, completely surrounding the connections and fittings. corrugated rotisserie gas line Fig. 4 Fig. 4a NOTE: After checking the connections and fittings in Figure 4, replace the control panel in the same manner as it was removed. Take special care to be sure the valve ends ar
