Summary of the content on the page No. 1
GPS NAVIGATION SYSTEM
DNX SERIES
DNX5360 DNX5360M
MONITOR WITH DVD RECEIVER
DDX SERIES
DDX5036 DDX5036M
INSTALLATION MANUAL
© B54-4766-10/01 (MW/M2W/XW)
Summary of the content on the page No. 2
Accessories Installation Procedure 1. To prevent a short circuit, remove the key from the 1 0* ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the speaker wires of the wiring harness. ..........1 ..........2 4. Connect the wiring harness wires in the following order: ground, battery, ignition. 2 !* 5. Connect the wiring harness connector to the unit. 6. Install the unit in your car. 7. Reconnect the - battery. DNX SERIES on
Summary of the content on the page No. 3
• This unit has the cooling fan to decrease the internal ¤ temperature. Do not mount the unit in a place where the • Mounting and wiring this product requires skills and cooling fan of the unit are blocked. Blocking these openings experience. For safety’s sake, leave the mounting and wiring will inhibit the cooling of the internal temperature and work to professionals. result in malfunction. • Make sure to ground the unit to a negative 12V DC power Cooling fan supply. • Do not install th
Summary of the content on the page No. 4
Connection If you connect the ignition wire (red) and the battery ¤ wire (yellow) to the car chassis (ground), you may Ignition key cause a short circuit, that in turn may start a fire. Always switch connect those wires to the power source running through the fuse box. ACC A Ignition wire (Red) B A Car fuse box Battery wire (Yellow) Car fuse box B (Main fuse) FM/AM Antenna Cord Ground wire (Black) - antenna input (To car chassis) C C Battery Connect to the vehicle's parking brake ⁄ dete
Summary of the content on the page No. 5
GPS Antenna (Accessory 2) (see page 8) FUSE ( 15A ) Accessory 1 REVERSE STEERING WHEEL REMOTE CONT REMOTE INPUT White/Black To front left speaker + White Gray/Black ILLUMI To front right speaker + Gray Green/Black MUTE To rear left speaker + Green Purple/Black To rear right speaker + ANT. CONT Purple P CONT | English 5
Summary of the content on the page No. 6
System Connection USB device USB terminal (commercially available) Rear View Camera input • Visual input (Yellow) Audio/Visual output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) Visual input (iPod/AV input 2 switchable) Resistance-free mini plug (3.5φ) Audio input (iPod/AV input 2 switchable) Resistance-free stereo type mini plug (3.5φ) Rear Preout • Audio left output (White) • Audio right output (Red) Front Preout • Audio left output (White) • Audio right ou
Summary of the content on the page No. 7
Optional Accessory Connection iPod (commercially available) KCA-iP301V (Optional Accessory) Audio Output (Black) Visual Output (Yellow) (DDX5036/ DDX5036M only) USB terminal Navigation System (Optional Accessory) KCA-BT200 (Optional Accessory) input Connection cable (Included in the Navigation System) TV Tuner (Optional Accessory) Navigation units that can be connected ⁄ to this unit. (As of December, 2009): KNA-G630 KNA-G630CN For latest information, access the www.kenwood.com/cs/ce/.
Summary of the content on the page No. 8
Installing the GPS Antenna (DNX SERIES only) GPS antenna is installed inside of the car. It should be installed as horizontally as possible to allow easy reception of the GPS satellite signals. To mount the GPS antenna inside your vehicle: 1. Clean your dashboard or other surface. 2. Peel the backing off of the adhesive on the bottom of the metal plate (accessory 3). 3. Press the metal plate (accessory 3) down firmly on your dashboard or other mounting surface. You can bend the metal plate
Summary of the content on the page No. 9
Installing the Escutcheon Installing the Escutcheon For Toyota/Scion 1. Attach accessory 4 to the unit. 1. Cut out accessory 5 as illustrated. Cutting line Accessory 5 Accessory 4 2. Fold double-sided adhesive (accessory 6) along For General Motors the slit and attach it to accessory 5 cut-out 1. Cut out accessory 5 to meet the shape of the against the center rib as illustrated. Use 2 pieces of opening of the center console. accessory 6 for 1 accessory 5 cut-out. 2. Attach accessory 5 to the
Summary of the content on the page No. 10
Installation for Monitor/Player Unit Installation on Toyota, Nissan or Mitsubishi Car using Brackets Accessory 7 (M5x6mm) or Accessory 8 (M5x7mm) Car Bracket Accessory 7 (M5x6mm) or Accessory 8 (M5x7mm) | 10 DNX SERIES/ DDX SERIES
Summary of the content on the page No. 11
| English 11
