Summary of the content on the page No. 1
®
PMC14E Series High-Resolution
14-Inch Color Monitors
Installation/Operation Manual
C929M-B (2/97)
Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981
FAX (800) 289-9150 or (1-559) 292-3827
International customers call 1-559-292-1981 or FAX 1-559-348-1120
Summary of the content on the page No. 2
CONTENTS Section Page 1.0 GENERAL ..................................................................................................1 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 1 2.0 DESCRIPTION ..........................................................................................4 2.1 MODELS ............................................................................................4 2.2 OPTIONAL ACCESSORIES .......................................................
Summary of the content on the page No. 3
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or 6P enclosure, it is designed for Indoor use only and it must not be installed where exposed to rain and moisture. 4. Only use replacement parts recommended by Pelco.
Summary of the content on the page No. 4
1.1 IMPORTANT SAFEGUARDS 1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed. 5. Cleaning - Unplug the unit from the outlet before cleaning. Do not use liquid
Summary of the content on the page No. 5
13. Power Lines - An outdoor system should not be located in the vicinity of over- head power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outdoor system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. U.S.A. models only - refer to the National Electrical Code Article 820 regarding installation of CATV systems. 14. Overloading - Do not overload outl
Summary of the content on the page No. 6
2.0 DESCRIPTION The PMC14E Series provides 14-inch (36 cm), color, high-resolution monitors. Monitor Features •Two video and audio input channels (one passive) with looping output. Video inputs include connectors for either a standard composite video signal or Y/C (Super VHS) signal. • Manual or automatic switching between channels with adjustable dwell time • Video tape recorder input and output • High resolution 480 lines • Comb filter for improved picture quality • 120 VAC or 230 VAC operati
Summary of the content on the page No. 7
3.0 INSTALLATION 3.1 BACK PANEL CONNECTIONS CAUTION: Do not install Refer to Table A for the type of video coaxial cable to use. this monitor in an exces- Refer to Figure 1 for rear panel connections. sively hot location, or in any way obstruct the ventilation Connect equipment to the monitor as follows. There are several options for inputs 1 openings in the cabinet. Pre- and 2 as shown on this and the following pages. Select the appropriate one. mature component failure or damage to the cabin
Summary of the content on the page No. 8
Input 1 or 2 (Input from Switcher or Matrix Control System - Video Only) 1. Refer to Figure 3. Connect the video output from the video switcher or matrix control equipment to Input 1 or Input 2 on the output monitor. 2. Set the 75-ohm/HIGH switch for 75 ohms if you are using Input 1. OUTPUT MONITOR VIDEO SWITCHER OR MATRIX SET FOR 75 OHMS IN OUT 75 ohm HIGH INPUT 2 OUTPUT VIDEO INPUT 1 VIDEO AUDIO VIDEO 2 VIDEO AUDIO AUDIO AUDIO AC INPUT INPUT OUTPUT INPUT OUTPUT Figure 3. Input from Switcher or
Summary of the content on the page No. 9
Input 1 (Dedicated Monitor Application - Video Only, No Camera Control) 1. Refer to Figure 5. Connect the video cable from the camera to the IN connec- tor of Input 1 on the feed monitor. Connect another video cable from the OUT connector of the feed monitor to the video switcher or matrix control equip- ment. 2. Set the 75-ohm/HIGH switch for HIGH. FEED MONITOR VIDEO SWITCHER OR MATRIX VIDEO INPUT SET FOR HIGH IN OUT 75 ohm HIGH INPUT 2 OUTPUT VIDEO INPUT 1 VIDEO AUDIO VIDEO 2 VIDEO AUDIO AUDIO
Summary of the content on the page No. 10
VTR Connections Refer to Figure 7. Connect the video and audio connections from the monitor to a video recorder if desired. Power Plug the appropriate end of the power cable into the AC INPUT on the monitor. Plug the other end into a utility outlet. IN OUT 75 ohm HIGH INPUT 2 OUTPUT VIDEO INPUT 1 VIDEO AUDIO VIDEO 2 VIDEO AUDIO AUDIO AUDIO AC INPUT INPUT OUTPUT INPUT OUTPUT VIDEO IN VIDEO OUT AUDIO IN AUDIO OUT Figure 7. VTR Connections 8 Pelco Manual C929M-B (2/97)
Summary of the content on the page No. 11
3.2 FRONT PANEL CONTROLS Refer to Figure 8. Set the controls on the front panel of the monitor as follows: 1. Set the PAL/NTSC switch for NTSC video format if you have a PMC14E moni- tor. Set the switch for PAL video format if you have a PMC14EX monitor. 2. Set the VTR/VIDEO switch for the signal input that you are using. • Select VTR if you want to play a VCR that is connected to the VTR termi- nals on the back of the monitor. • Select VIDEO if you want video and audio from equipment that is c
Summary of the content on the page No. 12
4.0 OPERATION There are two sources of video and audio input: • VTR (video tape recorder) •Video 1 and Video 2 Only one source can be selected at a time. To select the input from a video recorder, set the VTR/VIDEO switch on the front panel in the VTR position. In this position, the video and audio signals are sent to the monitor and through the OUTPUT connectors to any equipment connected to them. To select the input from Video 1 and/or Video 2: 1. Set the VTR/VIDEO switch on the front panel i
Summary of the content on the page No. 13
5.0 MAINTENANCE To reduce the risk of electric shock, do not remove the cover or back. No user- serviceable parts are inside. Refer servicing to qualified personnel. Some household aerosol sprays, cleaning agents, solvents, or polishes may dam- age the cabinet finish. Clean the cabinet with water and mild soap. Use a soft cloth for drying. If the quality of the picture on the monitor is poor and cannot be improved, inspect all system connections and cable runs. Pelco Manual C929M-B (2/97) 11
Summary of the content on the page No. 14
6.0 SPECIFICATIONS ELECTRICAL Input Power PMC14E 120 VAC, 60 Hz PMC14EX 230 VAC, 50 Hz Power Consumption PMC14E 65 W PMC14EX 70 W System PMC14E NTSC (525 lines, 60 fields per second) PMC14EX PAL (625 lines, 50 fields per second) Picture Tube: 14 inches (36 cm) measured diagonally Effective Picture Size Height: 8.27 inches (21.0 cm) Width: 11.0 inches (28.0 cm) Input Signal: Composite video, negative synch -Y: 1.0 Vp-p -C: 0.286 Vp-p Subcarrier Frequency Synch Range at Room Temperature: 3.57954
Summary of the content on the page No. 15
GENERAL Dimensions: 13.8" W x 12.4" H x 14.6" D (35 x 31.5 x 37.1 cm) Finish: Steel cabinet painted dark gray. Black bezel around the screen. Operating Temperature: 32° to 104° F (0° to 40° C) Humidity: 0% to 90% (non-condensing) Connectors Video Input, Output: BNC Y/C Input, Output: 4-pin mini-Din Audio Input, Output: RCA VTR Input, Output: RCA Power Cord: PMC14E 3-wire power cord with grounded plug PMC14EX “Euro” style grounded power cord Weight Shipping: 31.74 lbs (14.4 kg) Pelco Manual C929
Summary of the content on the page No. 16
7.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. ® • Three years on Genex Series products (multiplexers, server, and keyboard). ® • Three years on Camclosure and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, M
