Summary of the content on the page No. 1
www.skylinkhome.com
Emergency Dialer
TM
DIAL-ALERT
MODEL : AD-433S
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Tel : (800) 304-1187
Fax : (800) 286-1320
PAT. D410633
101A320 JUNE, 2004 Email : support@skylinkhome.com 6243000B1
English
Summary of the content on the page No. 2
SKYLINK TECHNOLOGIES INC. Your Guide to the Emergency Dialer TM DIAL-ALERT MODEL: AD-433S Emergency Dialer TM DIAL-ALERT AD-433S USER'S INSTRUCTIONS The AD-433S Emergency Dialer contains all the above items. –2– English 9 VOLT
Summary of the content on the page No. 3
PACKAGE CONTENTS TABLE OF CONTENTS All materials required for installation are included with this package PACKAGE CONTENTS............................................................................................4 ... OVERVIEW.........................................................................................................5 1 Dial-Alert (AD-433S) INSTALLATION.......................................................................................................................6
Summary of the content on the page No. 4
OVERVIEW INSTALLATION Automatically call for help when emergency The Dial-Alert is installed using the screws provided. We have also included double sided tape, to use for temporary installation while you are positioning The AD-433S Dial-Alert dials as many as 9 pre-programmed telephone numbers the dialer. Once the dialer is positioned correctly, install it permanently with and sends a personalized pre-recorded message. Each telephone number screws. We have also included wall anchors and a templ
Summary of the content on the page No. 5
INSTALLATION INSTALLATION Switch Setting 2. Thread the telephone line through the top hole in the back of the unit and plug it into 1. Tone/Pulse Switch the "LINE" jack. If you want to have an This dialer supports both Tone and Pulse answering machine on the same line as dialing. In order to change the setting, you the dialer, thread the phone line through the need to open the case by pressing the two bottom hole in the back of the unit and plug tabs on top of the dialer and pull open the front
Summary of the content on the page No. 6
LIGHTS AND SOUNDS STANDARD PROGRAMMING Below is an explanation of the lights and sounds of the Dial-Alert When you plug in the dialer for the first time, you will hear a double beep and all the lights will be on for 2 seconds, the keypad will continue to flash and the clock will be set to 12:00. LIGHTS ACPWR light on dialer is being powered by AC adapter. PROGRAM THE TIME CLOCK ACPWR light off dialer is not receiving any AC power. 1. Press the [L] key, display will show “L”. LOBATT. light off ba
Summary of the content on the page No. 7
STANDARD PROGRAMMING STANDARD PROGRAMMING PLAYBACK PRE-RECORDED MESSAGE want to keep the dialer at 3 attempts, press the [MEM] key. To change the redial count, enter a number from 1 - 9 when display shows “rEdIAL 3” . Press and release the [R/P] key, display will show “PLAY” and the dialer will 6. Th e display will now show “rEPEAt 3”. This is the repeat count which is beep. The message is then played back. the number of ti mes the message will be repeated during that one ca ll. The If you want
Summary of the content on the page No. 8
STANDARD PROGRAMMING STANDARD PROGRAMMING TO REVIEW OR MODIFY THE PRE-PROGRAMMED PHONE NUM- C. Storing telephone numbers in memory (Sends the numeric BERS, THE REDIAL COUNT AND/OR THE REPEAT TIMES OF A information to pager only) PHONE NUMBER. 1. Press the [MEM] key, the display will show a letter “M” on the upper left corner. If nothing is entered within 5 seconds, the display will return to the 1. Press the [MEM] key, display will show an “M” in the upper right corner. clock mode. 2. Select th
Summary of the content on the page No. 9
ADVANCED PROGRAMMING ADVANCED PROGRAMMING PROGRAM THE CALLING TIME and before you can enter the numeric information (i.e. phone number). The display will show a "P" if a pause period is entered. This pause period is The calling time is the amount of time the phone will ring until the call is dis- factory set at 5 seconds but can be changed from 1 - 9 seconds. You may contected. If the phone is not picked up within this period of time, the dialer also insert multiple pause periods to suit your ap
Summary of the content on the page No. 10
ADVANCED PROGRAMMING ADVANCED PROGRAMMING To erase transmitters/sensors/security systems from the dialer: PROGRAM THE ID CODE OF A TRANSMITTER 1. Press the [L] key, the display will show “ L ”. Before any transmitter/sensor/security system can activate the Dial-Alert, 2. Press the [6] key, the display will show “ L 6 ErASE “. they must be learned (programmed) to communicate with each other. Once they are learned, the button on the transmitter, a door with the door/window 3. Press the [#] key
Summary of the content on the page No. 11
ADVANCED PROGRAMMING ADVANCED PROGRAMMING When the universal dial tone is turned off, and no dial tone is detected within 1 Entering a premises using the delay dialing minute (after the dialer is activated), the display will show “no LInE” and the If entering a premises through a door that is monitored with a door sensor, the backlit keypad will flash. To return to standby mode (Display shows the time), delay dialing is set to 0 seconds and the dialer is on, the dialer will dial the press and ho
Summary of the content on the page No. 12
ADVANCED PROGRAMMING CONNECT THE DIAL-ALERT WITH YOUR EXISTING ALARM SYSTEM You may connect your existing alarm system with the Dial-Alert so that the dialer will be triggered by your alarm system when it is activated. There are 2 ways you can connect your dialer with your existing alarm system. 1. Connect the dialer with the alarm system using hard wire (normally closed). 2. Connect the dialer with the alarm system using the Alarm Sensor (SS-433). Follow the diagram below for hardwiring the dia
Summary of the content on the page No. 13
BATTERY MAINTENANCE ADDITIONAL ACCESSORIES The AD-433S Dial-Alert comes with 1 battery that at some point you may have Additional sensors and transmitters as well as add on accessories are available to replace: to work with your Dial-Alert. One 9 volt alkaline battery for the Dial-Alert Motion Sensor (PS-433A) - Monitors area in a 110 degree ARC and up to Recommendation: Test your Dial-Alert periodically to ensure that the battery 40 feet away from the sensor is working. - 9V alkaline battery
Summary of the content on the page No. 14
ADDITIONAL ACCESSORIES ADDITIONAL ACCESSORIES Smoke Sensor (SS-433) Security Control Panel (SC-001) - Detects sound frequencies of existing smoke, - Four alarm modes (Day, Night, Away, Chime) carbon monoxide alarms - Four zones, each zone controls up to 6 - Activates Security Control Panel (SC-001) or decives Emergency Dialer (AD-433S) when the preset - Reliable design with microcontroller sound frequency is detected - 110dB siren - 9V alkaline battery included Audio Sensor (AS-433) Sile
