Summary of the content on the page No. 1
NV-MPS4 Music Port Server
Installation Guide
Summary of the content on the page No. 2
Summary of the content on the page No. 3
ANTENNA LEAD-IN WIRE GROUND CLAMPS ANTENNA DISCHARGE UNIT NEC SECTION 810-20 GROUNDING ELECTRIC CONDUCTORS SERVICE ENTRANCE GROUND CLAMPS POWER SERVICE GROUPING ELECTRODE SYSTEM NEC ART 250 NEC NATIONAL ELECTRICAL CODE PART H SAFETY NOTE: Where the MAINS plug or appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable
Summary of the content on the page No. 4
ENGLISH IMPORTANT SAFETY INSTRUCTIONS Danger 1. Read all safety and operating instructions before using this Exposure to extremely high noise levels may cause a permanent product. 2. All safety and operating instructions should be kept for future hearing loss. Individuals vary considerably to noise induced hearing reference. loss but nearly everyone will lose some hearing if exposed to sufficiently 3. Read and understand all warnings listed on the operating intense noise for a sufficient t
Summary of the content on the page No. 5
FRENCH IMPORTANTES INSTRUCTIONS DE SECURITE 1. Lire avec attention toutes les recommandations et précautions d'emploi avant d'utiliser ce produit. Danger 2. Toutes les recommandations et précautions d'emploi doivent être L‘exposition a des niveaux eleves de bruit peut provoquer une perte conservées afin de pouvoir s'y reporter si nécessaire. permanente de l’audition, Chaque organisme humain reagit 3. Lire et comprendre tous les avertissements énumérés dans les differemment quant a la perte
Summary of the content on the page No. 6
Table of Contents Introduction Page 3 Music Port Server Front Panel Features Page 4 Music Port Server Back Panel Features Page 5 I. Installing the NV-NV-MPS4 as part of a NuVo Distributed Audio System Audio Outputs Page 6 NuVoNet Connection Page 6 II. Accessing the Remote Configuration Tool Accessing the Remote Configuration Tool from the Local Area Network Page 8 Finding the IP Address for the NV-MPS4 Page 8 III. Setting Up the NV-MPS4 through the Remote Configuration Tool Machine Settings
Summary of the content on the page No. 7
Introduction The NV-NV-MPS4, or Music Port Server is designed to fully communicate with the NuVo Essentia, Grand Concerto and Renovia Distributed Audio Systems through its NuVoNet communication protocol. Properly installing the Music Port Server as a source component will provide full browsing to all of your personal music (both through iTunes and Media Player) as well as online Internet radio. Whether across the Web or from its internal 320 GB hard drive, the Music Port Server gives you ful
Summary of the content on the page No. 8
RS232 POWER 1 2 3 4 5 6 7 8 NV-NV-MPS4 Music Port Server Front Panel Features 1. Power: This button supplies power to the Music Port Server when the unit is plugged into an AC power source and the button is pushed. The associated blue LED will light. 2. USB Port: This USB port allow the Music Port Server to see and stream audio content from attached drives. This feature will be available on a future release. 3. NuVoNet Error LED: The Music Port Server is designed to communica
Summary of the content on the page No. 9
A B C D MODEL NV-NV-MPS4 Music Port Server L L USB USB ETHERNET Passthrough To NuVo NuVoNet RS232 RS232 R R AUDIO SYSTEM 1 2 3 4 5 6 7 NV-NV-MPS4 Music Port Server Back Panel Features 1. USB Ports: Three USB ports allow the Music Port server to see and stream audio content from attached drives. This feature will be available in a future release. 2. Ethernet: This RJ45 port allows the Music Port Server to connect to the home’s network. This enables the music files on the home’s
Summary of the content on the page No. 10
I. Installing the NV-MPS4 as Part of a NuVo Distributed Audio System The NV-MPS4 will fully communicate as a NuVoNet audio component with a few simple connections. Locate the NV-MPS4 component with the main component of the NuVo Distributed Audio System. Make all the connections first and plug it into an AC power source and press the Power button on the front panel. The NV-MPS4 operating system will automatically boot up. You will see considerable activity on the “HDD” hard drive status LED
Summary of the content on the page No. 11
If you are installing the Music Port Server with a Renovia System, plug the CAT5 directly into one of the three “NuVoNet” inputs on the back panel of the Renovia Source Hub, Fig. 3. Fig. 3 USB USB ETHERNET Passthrough To NuVo NuVoNet RS232 RS232 SYSTEM II. Accessing the Remote Configuration Tool The Remote Configuration Tool is a quick, easy setup for the operation of the Music Port Server. Once configured, it will be fully operational with any of the NuVoNet Audio Distribution Systems. Make
Summary of the content on the page No. 12
Understanding the LAN Error LED The front panel of the NV-MPS4 has a red LED designed to alert you to communication issues across its network, Fig. 5. The state of the LED indicates the nature of the problem. LED not lit: This indicates good communication. No problem is found. LED solid red: A cable connection at the “Ethernet” port on the back panel is not detected. LED blinking twice: There is no WAN, Wide Area Network detected or no Internet connectivity. LED blinking three times: This is
Summary of the content on the page No. 13
Finding the IP Address for the NV-MPS4 If the “music-port” name does not connect, you can look up the IP address assigned to the Music Port Server and type that into the browser address bar, i.e.. 192.168.0.124/config, Fig. 7. Fig. 7 To find the address, go to the Menu of a Control Pad in the System. Choose one of the Music Port Server outputs from a Control Pad. In the Menu, go to “Source Options” and then select “Source Info” . You will then see the selection “IP Address” . Highlight is
Summary of the content on the page No. 14
III. Setting Up the NV-NV-MPS4 through the Remote Configuration Tool Once you have opened the Remote Configuration Tool, setup of the Music Port Server is easy. Machine Settings The first tab of the setup utility is Machine Settings. The choices to note here are the Name Identification, time zone settings, for monitoring the correct time from the web, and a choice of automatically configuring the NV-MPS4 on the home’s network or assigning a static IP address. Machine Identification: This is a
Summary of the content on the page No. 15
Wired Ethernet: The default is to let the network automatically supply an address to the Music Port Server when is connected through the “Ethernet” port. If you choose, you can assign a static address using this drop-down menu, Fig. 12. Logging: This section is for technical support. If instructed to do so by a technical support person, you can upload log files to NuVo Technical support for troubleshooting purposes. When the “Machine Settings” choices are made, click “Save Changes” Fig. 12
Summary of the content on the page No. 16
Content: Here is where you set the streaming capabilities of the Music Port Server. Supply the user account information in each of the provider sections that apply to the intended use of the NV-MPS4, Fig. 14. Once this information is entered, click “Save Changes” . Fig. 14 3 Pandora Radio: Pandora is a free Internet music streaming service. Once you have created a Pandora account from your computer, you simply enter your account information into the Pandora Radio section of the Content p
Summary of the content on the page No. 17
Firmware: This tab allows you to update the firmware, load the computer based Music Port Client control, and setup music sharing with the Music Port Server, Fig. 15. Fig. 15 Firmware Update: This download utility will prompt you when a new version is available. When you click on the supplied link, the newest version will automatically update the NV-MPS4. If “No firmware update is currently available” appears, no further action is necessary. It is important to note that the NV-NV-MPS4 is n
Summary of the content on the page No. 18
IV. Loading and Using the Music Port Sync Tool The Music Port Sync Tool is a powerful application that allows any user network PC to contribute music to the Music Port Server hard drive. Loading the Music Port Sync Tool: You will find a link to the Music Port Sync Tool executable file in the Firmware tab of the Remote Configuration Tool. Click on the link and open the file, Fig. 16. You will be prompted to save the .exe file to a folder or run it from its current location. Fig. 16 The execu
Summary of the content on the page No. 19
Summary: The Summary tab provides overview of the Music Port Server. Here you will see the current operating version and IP address, Fig. 18. The Summary tab will provide a progress report of any music sync activity. Fig. 18 iTunes: This tab points to the actual library on the user’s hard drive, and syncs the chosen content with the Music Port Server. Under “Sync Settings” , you have the choice to “Automatically update iTunes music” . This choice will allow you to “Update all music” or “
Summary of the content on the page No. 20
Windows Media: The Windows Media tab works like the iTunes tab. The choices and actions taken by the Music Port Server are identical. The difference is that the Sync Tool is looking at the content in Windows Media Player. It is possible to share content both from iTunes and Media Player, Fig. 20. Fig. 20 Advanced: Rather than sharing music from a specific iTunes or Media Player library, you can point directly to a music folder or directory on the network. This allows any music content to
