Summary of the content on the page No. 1
MC9090-G RFID Mobile
RFID Integrator Guide Supplement
Summary of the content on the page No. 2
Summary of the content on the page No. 3
MC9090-G RFID Integrator Guide Supplement 72E-89963-04 Rev A September 2008
Summary of the content on the page No. 4
ii MC9090-G RFID Integrator Guide Supplement © 2008 by Motorola, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis. All sof
Summary of the content on the page No. 5
iii Revision History Changes to the original manual are listed below: Change Date Description -01 Rev A 12/2006 Initial Release -02 Rev A 3/2008 Added Laser Scanner Updated Wireless Section Updated Applications Section -03 Rev A 5/2008 Updated Program Tag settings Added Duty Cycle Paramameters -04 Rev A 9/2008 Added ETSI EN302-208 Tx-Channels Window
Summary of the content on the page No. 6
iv MC9090-G RFID Integrator Guide Supplement
Summary of the content on the page No. 7
Table of Contents Patents.................................................................................................................................................. ii Revision History.................................................................................................................................... iii About This Guide Introduction ........................................................................................................................................... ix
Summary of the content on the page No. 8
vi MC9090-G RFID Integrator Guide Supplement Resetting the Mobile Computer ........................................................................................................... 1-9 Performing a Warm Boot ............................................................................................................... 1-9 Performing a Cold Boot .................................................................................................................. 1-9 Performing a Clean Boot ........
Summary of the content on the page No. 9
Table of Contents vii Chapter 4: RFID Demo Application Introduction .......................................................................................................................................... 4-1 RFIDDemo Application ........................................................................................................................ 4-2 Using RFIDDemo to Read Tags From a Remote Reader ............................................................. 4-2 Launching the RFIDDemo Appli
Summary of the content on the page No. 10
viii MC9090-G RFID Integrator Guide Supplement Chapter 6: SymbolRoam Introduction .......................................................................................................................................... 6-1 SymbolRoam, Region Change ............................................................................................................ 6-2 Country Drop Down List .................................................................................................................
Summary of the content on the page No. 11
About This Guide Introduction This MC9090-G RFID Integrator Guide Supplement provides the unique set up and configuration procedures for the MC9090-G RFID mobile computers and accessories. This guide is intended as a supplement to the MC909X Integrator Guide, P/N: 72E-72216-xx. Procedures common to the MC909X series of products are referenced to the MC909X Integrator Guide. NOTE Screens and windows pictured in this guide are samples and may differ from actual screens. Documentation Set Th
Summary of the content on the page No. 12
x MC9090-G RFID Integrator Guide Supplement Configurations This guide covers the following configurations: Data Operating Configuration Radios Display Memory Keypad Capture System MC9090-G WLAN: 802.11a/b/g Color 64 MB RAM Laser Scan Windows 53-key RFID RFID WPAN: Bluetooth 128 MB Imager Mobile 5.0 Flash RFID Chapter Descriptions Topics covered in this guide are as follows: • Chapter 1, Getting Started, provides information on charging the RFID reader battery and resetting. • Chapter 2, Accessor
Summary of the content on the page No. 13
About This Guide xi Notational Conventions The following conventions are used in this document: • “RFID Reader”, “reader” or “mobile computer” refers to the Motorola MC9090-G RFID reader. • Italics are used to highlight the following: • Chapters and sections in this guide • Related documents • Bold text is used to highlight the following: • Dialog box, window and screen names • Drop-down list and list box names • Check box and radio button names • Icons on a screen • Key names on a keypad • But
Summary of the content on the page No. 14
xii MC9090-G RFID Integrator Guide Supplement Service Information If an equipment problem occurs, contact the appropriate regional Support Center for contact information. Before calling, locate the model number and serial number. Call the Support Center from a phone near the scanning equipment so that the service person can try to talk through the problem. If the equipment is found to be working properly and the problem is symbol readability, the Support Center will request samples of bar cod
Summary of the content on the page No. 15
Chapter 1 Getting Started Introduction This chapter lists the accessories for the MC9090-G RFID mobile computer and explains how to install and charge the batteries, replace the strap and start the mobile computer for the first time. NOTE This MC9090-G RFID Integrator Guide Supplement is intended as a supplement to the MC909X Integrator Guide, P/N: 72E-72216-xx. Procedures common to the MC909X series of products are referenced to the MC909X Integrator Guide. MC909X Integrator Guide The MC909X
Summary of the content on the page No. 16
1 - 2 MC9090-G RFID Integrator Guide Supplement Unpacking the Mobile Computer Carefully remove all protective material from around the mobile computer and save the shipping container for later storage and shipping. Verify that all equipment listed below was received: • Mobile computer • Lithium-ion battery • Strap, attached to the mobile computer • Stylus, in the stylus silo • Regulatory Guide • Quick Start Guide (poster) Inspect the equipment for damage. If any equipment is missing or damaged,
Summary of the content on the page No. 17
Getting Started 1 - 3 Accessories Table 1-1 lists the accessories available for the MC9090-G RFID. Table 1-1 MC9090-G RFID Accessories Accessory Description Cable Adapter Module Snap-on required to connect the following cables to the mobile computer. (CAM) • AC line cord (country-specific) and power supply, charges the mobile computer. • Auto charge cable, charges the mobile computer using a vehicle’s cigarette lighter. • DEX cable, connects the mobile computer to a vending machine. • Seria
Summary of the content on the page No. 18
1 - 4 MC9090-G RFID Integrator Guide Supplement Getting Started In order to start using the mobile computer for the first time: • Install the main battery • Charge the main battery and backup battery • Start the mobile computer • Configure the mobile computer The main battery can be charged before or after it is installed. Use one of the spare battery chargers to charge the main battery (out of the mobile computer), or one of the cradles to charge the main battery installed in the mobile compu
Summary of the content on the page No. 19
Getting Started 1 - 5 Charging the Battery Charging the Main Battery and Memory Backup Battery Before using the mobile computer for the first time, charge the main battery until the amber charge indicator light remains lit (see Table 1-2 on page 1-6 for charge status indications). Charge time is less than four hours. The mobile computer can be charged using a cradle, the CAM with a charging cable, or the MSR with the appropriate power supply. The mobile computer is equipped with a memory back
Summary of the content on the page No. 20
1 - 6 MC9090-G RFID Integrator Guide Supplement Charging the Main Battery Charge the main battery in the mobile computer using a cradle, the CAM with a charging cable, or the MSR with the appropriate power supply. 1. Ensure the accessory used to charge the main battery is connected to the appropriate power source (see Chapter 2, Accessories for setup information). 2. Insert the mobile computer into a cradle or attach the appropriate snap-on module. 3. The mobile computer starts to charge autom
