Chief Manufacturing PFC Series user manual

Summary of the content on the page No. 1

INSTALLATION INSTRUCTIONS
Display Carts
MFC, PFC Series

Summary of the content on the page No. 2

Installation Instructions MFC, PFC Series DISCLAIMER WARNING: Failure to read, thoroughly understand, and CSAV, Inc., and its affiliated corporations and subsidiaries follow all instructions can result in serious personal injury, (collectively, "CSAV"), intend to make this manual accurate and damage to equipment, or voiding of factory warranty! It is the complete. However, CSAV makes no claim that the information installer’s responsibility to make sure all components are contained herein covers

Summary of the content on the page No. 3

MFC, PFC Series Installation Instructions DIMENSIONS MFC PFC [177] 3

Summary of the content on the page No. 4

Installation Instructions MFC, PFC Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging lo

Summary of the content on the page No. 5

Installation Instructions MFC, PFC Series TOOLS REQUIRED FOR INSTALLATION 3/16" (Included) PARTS B (1) (right) A (1) (left) D (4) C (2) E (1) F (1) J (1) G (1) 3/16" PFC H (1) Only MFC Only L (4) M (4) N (4) P (4) K (1) 5/16-18 x 4-1/4" 3/16" 5/16-18 x 3/4" 5/16-18 x 2-3/4" 5/16" 5

Summary of the content on the page No. 6

MFC, PFC Series Installation Instructions 2. Attach center post (E) to leg assembly using four 5/16-18 x 2-3/4" button head cap screws (M) and four 5/16" washers (P). (See Figures 2 and 3) ASSEMBLY (E) CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the hex head drill bit and power drill to complete the attachment. Assembling Cart 1.

Summary of the content on the page No. 7

Installation Instructions MFC, PFC Series Attaching Display to Cart WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY 5 MAY LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to ensure the total amount of weight placed on the cart does not exceed 125 lbs (56.70 kg) for the MFC, and 200 lbs (90.72 kg) for the PFC. CAUTION: Before attaching display to cart set the brakes on the back wheels by pressing down on the tab. (See Figure 5) Press down to set brakes Figu

Summary of the content on the page No. 8

MFC, PFC Series Installation Instructions Tilting Display o (Rear The display can be tilted up to 15 either backward or forward 2 view of (Front view from a straight upright position. center post) of center post) 1. Turn knob counterclockwise on back of head assembly to 3 loosen the tilt. (See Figure 9) 1 Exits for signal cables 3 1 loc lock displ k display ay Place optional bolt Snap-on (not provided) here 4 covers to lock in an upright Exit for position. power cables (MFC Shown) Figure 9 o 2.

Summary of the content on the page No. 9

Installation Instructions MFC, PFC Series 2. Pull back on flag on upper mounting hole and press pin down into "Open" position. (See Figure 13) WARNING: EACH DISPLAY MAY WEIGH IN EXCESS OF 40 LBS! Always use two people and proper lifting techniques when installing or positioning display on stand. Do NOT push 3. Carefully lift display from cart. cart near top 4. Lift up on pin and place flag back against faceplate to return it to "Closed" position. (See Figure 13) Push cart near middle Remove bolt

Summary of the content on the page No. 10

MFC, PFC Series Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112 8809-000038 Rev.B 2007 Chief Manufacturing www.chiefmfg.com P +86-755-8996 9226 ; 8996 9236 ; 8996 9220 06/07 F