Summary of the content on the page No. 1
®
™
TITAN T2
Charger / Power Supply
OWNER’S MANUAL
Summary of the content on the page No. 2
TABLE OF CONTENTS INTRODUCTION ..........................................................................................1 FEATURES....................................................................................................1 SAFEGUARDS..............................................................................................2 GROUNDING/EARTHING...........................................................................2 Charging ..................................................
Summary of the content on the page No. 3
INTRODUCTION The TITAN T2 is a simultaneous 2 position Interactive fast charger with 70 watt DC camera power supply. It incorporates all of the Logic Series circuits that are employed in every Anton/Bauer charger. The InterActive charge programming provides all charge termination and protection routines for safe, reliable, chemistry independent charging. Like all Anton/Bauer chargers, everything is automatic. Once a battery is placed onto the charger, it will automatically go into
Summary of the content on the page No. 4
SAFEGUARDS Power Sources: This unit was designed to operate at mains voltages from 90 to 250 Volts AC, 50-60 Hz. Risk of Electrical Shock: Refer servicing to qualified service personnel. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. GROUNDING/EARTHING IMPORTANT WARNING: THIS APPARATUS MUST BE EARTHED. To ensure safe operation, the three pin plug supplied must be inserted only into a standard three-pin power point which is effectively grounded through
Summary of the content on the page No. 5
Charging As with all Anton/Bauer chargers, charging with TITAN T2 is fully automatic. Mount any Digital Logic Series or Logic Series battery to the TITAN T2 and it will automatically determine the appropriate charge routine and execute it. Applications The Titan T2 will charge any Anton/Bauer Logic Series Gold Mount battery including model: ProPac 13/14, Trimpac 13/14, Digital ProPac 13/14, Digital Trimpac 13/14, HyTRON, Dionic 80 or ProFormer battery. NOTE: Anton/Bauer recommends tha
Summary of the content on the page No. 6
Three Stage Charging Methodology In general, the TITAN T2 will deliver a three stage charge routine to each battery. 1. Stage One will deliver a high rate charge matched to the capabilities of the battery (typically a one or two hour rate, depending on battery type). During this stage, six separate cutoff methods are in operation, simultaneously, ensuring the fastest, safest charge for that battery: TCO - Temperature cutoff which stops the Stage one charge precisely when a temperature
Summary of the content on the page No. 7
NOTE: Batteries may be kept on a charger until ready for use. The Lifesaver mode will keep them 100% charged. LED Indications The TITAN T2 has two sets of three LEDs (one red, two green). The green status LED indicates: Steady green – line voltage is present with no power drawn through camera output; Flashing green - line voltage is present, powering camera; Off – line voltage not present, camera powered by battery, if there is a battery presently mounted on Titan T2. The red and g
Summary of the content on the page No. 8
OPERATION AS DC CAMERA SUPPLY FROM MAINS The TITAN T2 will automatically operate as a DC power supply once power is drawn from the 4 pin XLR, for example, when the camera, or other device is turned on. There are no switches, it is fully automatic. The green status LED will flash indicating that the unit is operating as a power supply. Once the camera or other device drawing power from 4 pin XLR is turned off the Titan T2 will revert to charging the battery. If the DC power supply has
Summary of the content on the page No. 9
FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. O
Summary of the content on the page No. 10
WARRANTY IMPORTANT: PLEASE MAIL WARRANTY REGISTRATION CARD WITHIN TEN (10) DAYS OF PURCHASE. We must have this card on file with our Customer Support Group to establish this warranty. Proper registration will also enable us to provide update information on the battery system. All new Anton/Bauer products have been thoroughly tested and inspected prior to shipment. This product is warranted against defect in materials and workmanship for a period of one (1) year from date of purchase
Summary of the content on the page No. 11
® The worldwide standard ® sm The power behind the best cameras capturing the best images in the world. The following are trademarks of Anton/Bauer, Inc.: ACS, ADM, Anton/Bauer, Anton/Bauer logo and parallelogram design, Aspekt, Automatique, DataTap, Dionic, ElipZ, ElightZ, EgripZ, Gold Mount, HyTRON, Impac, InterActive and design, LifeSaver, Logic Series, Logic Series logo, Maxx man logo design, MicroCode, PowerStrap, Probe, Proformer, ProPac, RealTime, SSP, Satelli
