Summary of the content on the page No. 1
Summary of the content on the page No. 2
Philips Selecon Offices Philips Selecon - Dallas Philips Selecon - Auckland 10911 Petal Street 19-21 Kawana Street Dallas, TX 75238 Northcote, Auckland 0627 Tel: +1 214-647-7880 New Zealand Fax: +1 214-647-8030 Tel: +64 9 481 0100 Fax: +64 9 481 0101 Philips Selecon - New York Philips Selecon - Europe 267 5th Ave, 4th Floor Marssteden 152 New York, NY 10016 Enschede 7547 TD Tel: +1 212-213-8219 The Netherlands Fax: +1 212-532-2593 Tel: +31 53 4500424 Fax: +31 53 4500425 Philips Selecon - Asia Un
Summary of the content on the page No. 3
PLCYC LED Luminaires Installation & User’s Manual IMPORTANT INFORMATION Warnings and Notices When using electrical equipment, basic safety precautions should always be followed including the following: a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. b. Do not use outdoors. c. Do not mount near gas or electric heaters. d. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. e. The use of accessory equipment not recomme
Summary of the content on the page No. 4
Installation & User’s Manual PLCYC LED Luminaires TABLE OF CONTENTS Philips Selecon Offices........................................................................................................................... Inside Front Cover IMPORTANT INFORMATION Warnings and Notices......................................................................................................................................................... 1 Additional Resources for DMX512.....................................
Summary of the content on the page No. 5
PLCYC LED Luminaires Installation & User’s Manual PREFACE 1. About this Manual The document provides installation and operation instructions for the following products: • PLCYC LED Luminaire (PLCYC1-03). Please read all instructions before installing or using this product. Retain this manual for future reference. Additional product information and descriptions may be downloaded at www.seleconlight.com Note: All PLCYC LED Luminaires are universal voltage (100VAC to 240VAC, Auto-ranging). 2. Acce
Summary of the content on the page No. 6
Installation & User’s Manual PLCYC LED Luminaires PLCYC LED LUMINAIRE OVERVIEW 1. PLCYC LED Luminaire Components Major Luminaire Components 4 2 3 Front of Unit Rear of Unit 1 1) PLCYC LED Luminaire Head 2) LCD Display Menu System (see "LCD Display / Menu System" on page 5 for more information) 3) Tilt Axis Point / Locking Handle 4) Yoke / Mounting Point Figure 1: PLCYC LED Luminaire Components Luminaire Connections and LCD Display Rear View E B A PowerCon (AC) Input A B PowerCon (AC) Output F C
Summary of the content on the page No. 7
PLCYC LED Luminaires Installation & User’s Manual LCD Display / Menu System 3 1 2 1) LCD Display (Menu System) 2) Preset / Intensity / Menu Access Buttons 3) Function (Menu System) Select Push Buttons Note: For Menu operation and programming details, refer to "LCD Menu Operation" on page 9. Figure 3: PLCYC LED Luminaire LCD Display & Menu System PLCYC LED Luminaire Components 5
Summary of the content on the page No. 8
Installation & User’s Manual PLCYC LED Luminaires INSTALLATION AND SET UP 1. Power Requirements The PLCYC LED Luminaire operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire contains an auto-ranging power supply. Depending on supply voltage, each luminaire can draw up to 1.5 amps. Table 1: PLCYC LED Luminaire Voltage vs. Current Maximum Maximum number of number of Voltage Total Voltage Total units that can units that can (AC) Current (A) (AC) Current (A) be linked be linked
Summary of the content on the page No. 9
PLCYC LED Luminaires Installation & User’s Manual If the unit is supplied with an AC input cable but you did not order an AC input connector, Table 2 describes how to connect power to your PLCYC LED Luminaire. Field wiring of the PLCYC LED Luminaire is straight forward. A total of 3 wires/conductors need to be brought to the unit. The following wiring scheme is required: Table 2: PLCYC LED Luminaire AC Input Connections Wire Colour Purpose Brown Main / Line (100 to 240VAC) Blue Neutral Green/Yel
Summary of the content on the page No. 10
Installation & User’s Manual PLCYC LED Luminaires 4. Mounting PLCYC LED Luminaires offer a plastic monocoque yoke design for mounting by theatrical clamps or hooks (sold separately). For optimum performance and use, PLCYC LED Luminaires should be mounted and spaced as shown in Figure 5. How to read Figure 5: S • S = Spacing between fixtures D • D = Distance from fixture to projection surface. • A ratio of S = D x 0.9 is the formula used to cal- culate the optimum spacing for these fixtures. WARN
Summary of the content on the page No. 11
PLCYC LED Luminaires Installation & User’s Manual OPERATION AND PROGRAMMING 1. LCD Menu Operation The PLCYC LED Luminaire’s LCD Display and Menu System provides local control for accessing all the fixture’s status information, menu options, and settings. Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired. Upon power up, the LCD will display the main screen showing the product type/name. If DMX is enabled, the programmed address will ap
Summary of the content on the page No. 12
Installation & User’s Manual PLCYC LED Luminaires 2. LCD Menu System The LCD Display Menu system consists of several categories. Use the four arrow buttons as required (refer to Figure 7 on page 9) to access and make changes to the menu items. When the desired menu item is reached, press [OK] to display the menu options. Use navigation and [OK] buttons to view status and configure the LCD Menu as required. Note: Depending on the security settings, certain menu items may be password protected. Y
Summary of the content on the page No. 13
PLCYC LED Luminaires Installation & User’s Manual Menu Structure LCD Display / Menu System MAIN MENU Save as Preset Sub Menu Options Comments Users can: Off • Save the current settings (look) to a specific recallable Preset in the Select Preset to Save - (Option) Scratch Pad fixture’s memory. • Edit the levels (values) for Red, Scrolls and sets current user-defined Green, Blue, White, and Intensity Warm White* colour mix to various recallable values (in percent%) by using the presets in
Summary of the content on the page No. 14
Installation & User’s Manual PLCYC LED Luminaires Menu Structure (continued) Continued from previous page Edit a Preset Sub Menu Options Comments Users can: Off • Edit the current settings (look) to a specific recallable Preset in the fix- ture’s memory. • Edit the values for Red, Green, Scratch Pad Blue, White, and Intensity values (in percent%) by using the arrow buttons. • Once the values are adjusted, the Warm White* "Save Preset" menu option Select Preset to Edit - (Option) appears
Summary of the content on the page No. 15
PLCYC LED Luminaires Installation & User’s Manual Menu Structure (continued) Continued from previous page Settings Sub Menu Options Comments SETTINGS - (Option) See "Settings" on page 15 for details. Scrolls and sets the various fixture settings using arrow buttons. Lock Fixture Sub Menu Options Comments Use arrow buttons to make selection. Press [OK] to accept. Note, a password must be established (set) in LOCK - Are you sure? Yes (to Lock Fixture) / No order to lock a fixture. Locking the
Summary of the content on the page No. 16
Installation & User’s Manual PLCYC LED Luminaires Step 3. Select a Level to change ( Level 1 PIN / Level 2 PIN / Level 3 PIN). Step 4. Press [OK] to edit using the [UP ARROW], [DOWN ARROW], [LEFT ARROW] or [RIGHT ARROW] keys to enter a four-digit password (using 0 to 9). Step 5. Press [OK] to save changes. If you hit [ESC] (Escape) password will not be stored and process must be repeated. Step 6. Password is set. Note: The current security level is displayed next to the Security heading. Only
Summary of the content on the page No. 17
PLCYC LED Luminaires Installation & User’s Manual Protected Protected Presets are also Factory Calibrated, and by default are Protected from changes to their Colour Mix. Their Intensity can be changed. Protected Presets are Presets 5-25. They can be Un-Protected by setting "Protected" to "No"; see section on Settings. If Un-Protected these presets function like User Presets. The Factory Calibrated values for the protected presets can be re-loaded to the original factory calibration settings by s
Summary of the content on the page No. 18
Installation & User’s Manual PLCYC LED Luminaires General 30W, 40W, 50W, 70W, Sets the maximum power setting of the 1 Power Limit 100W 90W, 100W, 100W LED engine. When the Fixture Powers-Up what does it Off, Scratch Pad, output. Scratch Pad is an automatically Warm White, Cool saved Preset. Last Set is the last thing 1 Power-Up White, Day Light, Cool White coming out of the fixture, this could be Preset30, Preset31, Warm White with the intensity changed Last Set from that of the Preset.
Summary of the content on the page No. 19
PLCYC LED Luminaires Installation & User’s Manual DMX CONTROL This section contains information for operating the luminaire using DMX control in 16-Bit, 8-Bit, or 3-Channel (3- Chan) modes. For Menu options and detailed information, see "Settings" on page 15. Note: These tables assume a DMX start address of 1. When a different starting address is used, this address becomes channel 1 function and other functions follow in sequence. 1. 16-Bit Mode Table 3 provides DMX channel mapping of all DMX5
Summary of the content on the page No. 20
Installation & User’s Manual PLCYC LED Luminaires Table 3: PLCYC LED Luminaire DMX Channel Mapping (16-Bit Mode) Allows for luminaire timing of intensity. Profile should default to DMX 255 for smoothest console 13 Intensity Time 0 - 255 0 - 100% 255 fade times. Refer to "PLCYC LED Luminaire DMX Timing Channel Detail" on page 22 for more information on timing values. Allows for luminaire timing of LEDs. Profile should default to DMX 255 for smoothest console 14 Colour Time 0 - 255 0 - 100%
