Summary of the content on the page No. 1
S10L-9619-03
IBM Mobile Systems
ThinkPad 600/600E (2645)
Hardware Maintenance Manual
June 1999
Summary of the content on the page No. 2
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 117. Fourth Edition (June 1999) The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT ANY WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE LIMITED WARRANTIES OF MERCHANTA
Summary of the content on the page No. 3
Related Publications The following product publications are available through IBM or your IBM Authorized Dealer. Publication Part, Form Number Mobile Systems HMM 30H2356, S82G-1501-01 Volume 1: Laptop, Notebook, Portable, and ThinkPad Computers (Models L40, CL57, N45, N51, P70/P75, ThinkPad 300, 350, 500, 510, 710T, Expansion Unit, Dock I, Dock II) Mobile Systems HMM 30H2357, S82G-1502-03 Volume 2: ThinkPad Computers (Models 340, 355, 360, 370, 700, 701, 720, 750, 755) Mobile Systems HMM 84H80
Summary of the content on the page No. 4
Diskette Part, Form Number ThinkPad 300 (2615) 33G9361, S33G-9361 Advanced Diagnostics Diskette ThinkPad 350, 350C, 425, A211000, GA21-1000 425C (2618) Advanced Diagnostics Diskette ThinkPad 365 (2625) 76H7578, S30H-2498 Advanced Diagnostics Diskette ThinkPad 380/385 (2635) 06J0333, S06J-0333 Maintenance Diskette ThinkPad 390/i Series 1700 10L9942, S10L-9942 (2626, 2627) Diagnostic and Utilities Diskettes ThinkPad 500 (2603) 71G3702, S71G-3702 Advanced Diagnostics Diskette ThinkPad 510 (2604)
Summary of the content on the page No. 5
Contents General Descriptions . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . 1 Important Service Information .......... 1 Drive and Diskette Compatibility Matrix ..... 3 Safety Notices (Multi-lingual Translations) .... 3 Safety Information . . . . . . . . . . . . . . . 10 Laser Compliance Statement ........... 14 Read This First .................. 17 FRU Replacement Notices ............ 19 LCD Replacement Notice ........... 19 Screw Notices . . . . . . . .
Summary of the content on the page No. 6
Beep Symptoms . . . . . . . . . . . . . . . . 57 Audio-Related Symptoms . . . . . . . . . . . 58 CD-ROM-Related Symptoms . . . . . . . . . . 58 Function-Related Symptoms . . . . . . . . . . 60 Indicator-Related Symptoms . . . . . . . . . . 60 Infrared-Related Symptoms . . . . . . . . . . . 61 Keyboard- or TrackPoint-Related Symptoms . . . 61 LCD-Related Symptoms . . . . . . . . . . . . 62 Modem (DSP)-Related Symptoms ....... 62 PC Card-Related Symptoms .......... 63 Peripheral-Device-Related S
Summary of the content on the page No. 7
Introduction General Descriptions This chapter includes the descriptions for all ThinkPad models. Some descriptions might not apply to the particular computer. Introduction Important Service Information Important Diskette fixes are customer installable. The diskette fixes are located on the PC Company Bulletin Board Service (BBS). The direct phone line for modem connection is 919-557-0001 or tieline 255-0001. Advise customers to contact the PC Company HelpCenter at 800-772-2227 if they nee
Summary of the content on the page No. 8
Introduction Attention A customized setup configuration (other than default settings) may exist on the computer you are servicing. Running Automatic Configuration may alter those settings. Note the current configuration settings (using the View Configuration option) and verify that the settings are in place when service is complete. Hard Disk Drive Replacement Strategy: Always try to run a low-level format before replacing a hard disk drive. Attention The drive startup sequence in the comput
Summary of the content on the page No. 9
Introduction Drive and Diskette Compatibility Matrix The following table provides identification information for 3.5-inch drives. Diskette Drive Identifying Mark 3.5-Inch - 1.44MB 1.44 on the eject button 3.5-Inch - 2.88MB 2.88 on the eject button The following table provides compatibility information for 3.5-inch diskettes and 3.5-inch diskette drives. Diskette 1.44MB Drive 2.88MB Drive Capacity 1.0MB Read/Write Read/Write 2.0MB Read/Write Read/Write 4.0MB Not Compatible Read/Write The followin
Summary of the content on the page No. 10
Introduction Safety Notice 1 Before the computer is powered-on after FRU replacement, make sure all screws, springs, or other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. Avant de remettre l'ordinateur sous tension après remplacement d'une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixée
Summary of the content on the page No. 11
Introduction Safety Notice 2 Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble it, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas,
Summary of the content on the page No. 12
Introduction Safety Notice 3 The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l'exposez ni au feu ni à l'eau. Ne la mettez pas
Summary of the content on the page No. 13
Introduction Safety Notice 4 The lithium battery can cause a fire, explosion, or severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium. Elle pr
Summary of the content on the page No. 14
Introduction Safety Notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d'affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent
Summary of the content on the page No. 15
Introduction Safety Notice 6 To avoid shock, do not remove the plastic cover that surrounds the lower portion of the inverter card. Afin d'éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d'alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen. Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la parte inferiore de
Summary of the content on the page No. 16
Introduction Safety Notice 8 Before removing any FRU, power-off the computer, unplug all power cords from electrical outlets, remove the battery pack, then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d'alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d'interface. Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der
Summary of the content on the page No. 17
Introduction Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine. Keep your tool case away from walk areas so that other people will not trip over it. Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it. Insert the ends of your necktie or scarf inside clothing or fasten it with a nonconductive cli
Summary of the content on the page No. 18
Introduction If you need to work on a machine that has exposed electrical circuits, observe the following precautions: – Ensure that another person, familiar with the power-off controls, is near you. Attention: Another person must be there to switch off the power, if necessary. – Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back. Attention: There must be a complete circuit to cause electrical shock. By observing the abov
Summary of the content on the page No. 19
Introduction Safety Inspection Guide: The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of non-IBM features or options not covered by this inspection guide. If any unsaf
Summary of the content on the page No. 20
Introduction Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes 1. Use product-specific ESD procedures when they exceed the requirements noted here. 2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective. When handling ESD-sensitive parts: Keep the parts in protective packages until they are inserted into the product. Avoid contact
