Summary of the content on the page No. 1
Operator’s Manual
Triple Bagger Kit
Model 190-190-100
Model 190-192-190
IMPORTANT: Read safety rules and instructions carefully
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered,
brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state
laws (if any). If a spark arrester is used, it should be maintained in effective working order by the
Summary of the content on the page No. 2
TABLE OF CONTENTS Content Page Customer Support 2 Important Safe Operation Practices 3 Assembly & Operation 7 Illustrated Parts List 10 Warranty Back Cover FINDING MODEL NUMBER This Operator’s Manual is an important part of your new Triple Bagger Accessory. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information
Summary of the content on the page No. 3
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol—heed its warning. WARNING: The Battery and Engine Exhaust contains chemicals known to the State of C
Summary of the content on the page No. 4
26. Use only accessories and attachments approved for this dump cart, lawn roller, etc.) on slopes greater than 5 machine by the machine manufacturer. Read, degrees. When going down hill, the extra weight tends to understand and follow all instructions provided with the push the tractor and may cause you to loose control. (e.g. accessory or attachment. tractor may speed up, braking and steering ability are 27. Data indicates that operators, age 60 years and above, reduced, attachment may jac
Summary of the content on the page No. 5
or trailer bed with a plastic liner. Always place complete stop within approximately (5) five seconds after containers on the ground away from your vehicle operating the blade disengagement control. If the blades before filling. do not stop within the this time frame, your unit should be c. When practical, remove gas-powered equipment serviced professionally by an authorized dealer. from the truck or trailer and refuel it on the ground. 4. Check brake operation frequently as it is subjected t
Summary of the content on the page No. 6
SECTION 2: LOOSE PARTS The grass catcher kit is shipped with following loose parts in the carton. Please remove all loose parts, including the hardware pack, from the carton before discarding it. Compare with Figure 1 to check that all parts were included. Note that the kit and the hardware pack contain extra items which are not used on your unit. Grasscatcher Cover Assembly Support Tube (attached to cover) Discharge Chute Assembly Mounting Grass Bag Bracket Blades Chute Stop Bracket
Summary of the content on the page No. 7
SECTION 3: ASSEMBLY & OPERATION NOTE: References to left, right , front and rear of the tractor are from the operator’s position, unless otherwise stated. Before assembly, place the tractor on a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. Support For convenience, pivot the seat forward and leave it Tube in that position until the grass collector is fully mounted and assembled. Mounting Bracket Assembly Remove the hairpin clip and clevi
Summary of the content on the page No. 8
Remove the cutting deck from beneath the tractor NOTE: An extra set of carriage bolt and lock nut have (refer to instructions for Deck Removal in your tractor’s been supplied in your accessory kit. You may replace operator’s manual), then gently flip the deck over to the old hardware for the chute stop bracket with these expose its underside. new ones, or save for later use. Place a block of wood between the center deck housing baffle and the cutting blade to act as a Lock Nut stabilizer.
Summary of the content on the page No. 9
Insert the lower end of the chute tube over the discharge chute so that its two notches fit into the Insert chute tube here two corresponding notches on the discharge chute. See Figure 9. Secure by placing the ends of the two short retainer straps on the discharge chute over the pins on the chute tube. See Figure 9. Operation Your triple bagger kit is a valuable accessory to your tractor. Optimize its performance by operating correctly. Do not try to fit it to tractors other than thos
Summary of the content on the page No. 10
SECTION 4: PARTS LIST FOR MODELS 190-190-100 & 190-192-190 14 21 23 26 4 12 22 20 7 3 31 16 16 28 8 16 30 11 17 33 18 19 25 16 B 16 8 B C 8 See parts 9 24 29 6 27 2 13 break-down C 16 below 9 15 5 10 Components of Bag Assembly: Components of Cover Assembly pn # 664-04018: 50 35 45 49 47 A 51 43 40 48 45 44 37 34 46 A 36 42 38 39 40 10
Summary of the content on the page No. 11
Model 190-190-100 & 190-192-190 Ref. Part No. Description Ref. Part No. Description No. No. 17200A Catcher Support Bracket 742-04067 Blade : High Lift; Cub Cadet 1. 27. 17247 Tubing Adapter 777D03361 Logo: Cub Cadet 2. 28. 631-0221 Chute Elbow 783-0601 Catcher Support Bracket 3. 29. 664-04018 Cover Assembly (includes ref. 35 to 46) 783-0673 Catcher Support Bracket RH 4. 30. 683-0617 Bracket Assembly: Chute Stop 783-0764 Catcher Support Bracket LH 5. 31. 689-00002 Grasscatcher Support Assembly 78
Summary of the content on the page No. 12
MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Cub Cadet possesions and territories, except those sold through LLC with respect to new merchandise purchased and used in Cub Cadet’s authorized channels of export the United States, its possessions and territories. distribution. e. Replacement parts that are not genuine Cub Cadet “Cub Cadet” warrants this product against defects in material parts. and workmanship for a period of two (2) years commencing
