Summary of the content on the page No. 1
®
HUSQVARNA AUTOMOWER
260 ACX
OPERATOR’S MANUAL
Summary of the content on the page No. 2
Summary of the content on the page No. 3
TABLE OF CONTENTS 1. Introduction and safety .............................................................. 5 1.1 Introduction ..................................................................................... 5 ® 1.2 Symbols on Automower ...........................................................
Summary of the content on the page No. 4
TABLE OF CONTENTS Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance and function of products without prior notice. This Operator's Manual deals with version 2.7x of the mower’s control program. 4 - English
Summary of the content on the page No. 5
1. INTRODUCTION AND SAFETY 1. Introduction and safety 1.1 Introduction Congratulations on your choice of an exceptionally high quality product. To get the best results from your ® Husqvarna Automower requires knowledge of its function. This Operator's manual contains important information about the mower, how you install it and how you use it. The following system is used in the Operator's manual to make this easier: • Italic content indicates one of the following
Summary of the content on the page No. 6
1. INTRODUCTION AND SAFETY ® 1.2 Symbols on Automower These symbols can be found on the lawn mover. Study them carefully so you understand their significance. • Read through the Operator’s Manual carefully and understand the content before using your ® Automower . • The warnings and safety instructions in this Operator’s Manual must be carefully followed if the mower is to be used safely and efficiently. ® • Automower can only start when the main switch is moved to the
Summary of the content on the page No. 7
1. INTRODUCTION AND SAFETY 1.3 Symbols in the Operator’s Manual These symbols can be found in the Operator’s Manual. Study them carefully so you understand their significance. • Inspection and/or maintenance must be carried out with the main switch set to OFF. OFF • Always wear protective gloves when working with the mower’s underframe. • Never use a high-pressure washer or even ® running water to clean Automower . • A warning box indicates a risk of personal injury exist, especi
Summary of the content on the page No. 8
1. INTRODUCTION AND SAFETY 1.4 Safety instructions Use • Please read the Operator's Manual carefully and make sure you understand the instructions ® before using Automower . • It is not permitted to modify the original design of ® Automower . All modifications are made at your own risk. • Check that there are no stones, branches, tools, toys or other objects on the lawn that can damage the blades and cause the mower to stop. ® • Start Automower acco
Summary of the content on the page No. 9
1. INTRODUCTION AND SAFETY Transport The original packaging should be used when ® transporting Automower over long distances. To safely move from or within the working area: 1. Press the STOP button to stop the mower. If the anti-theft alarm (see page 57) is activated; enter the first digit of the PIN code. You select the four digit PIN code when you start the mower for the first time, see page 31. 2. Move the main switch to the OFF position if you intend to carry the m
Summary of the content on the page No. 10
2. PRESENTATION 2. Presentation This chapter contains information you should be aware of when planning the installation. ® An installation of Husqvarna Automower includes four main components: ® Automower , an automatic lawn mower that mows the lawn by moving in essentially an irregular pattern. The mower is powered by a maintenance-free battery. ® Charging station, where your Automower returns when the charge level in the battery becomes too low. The charging station has
Summary of the content on the page No. 11
2. PRESENTATION ® 2.1 Automower , what’s what? 2 7 3 7 6 10 8 5 1 4 9 11 15 14 12 13 17 18 16 20 19 22 23 27 21 24 25 26 The numbers in the picture correspond to: 1. Charging strip 15. Blade disc 2. Cutting height adjustment cover 16. Charging station 3. Catch button to open the cutting height adjustment 17. Contact strips cover 18. LED for operation check of the boundary wire 4. Ultrasonic sensors 19. Loop wire for the boundary wire and guide wire 5. Drive wheel 20. Transformer with
Summary of the content on the page No. 12
2. PRESENTATION ® 2.2 Function of Automower Capacity ® Automower 260 ACX is recommended for lawns up to 2 5500 m +/-20%. How large an area is mown depends primarily on the condition of the blades and the type of grass, growth rate and humidity. The shape of the garden is also significant. If the garden mainly consists of open lawns, ® Automower can mow more per hour than if the garden consists of several small lawns separated by trees, flower beds and passages.
Summary of the content on the page No. 13
2. PRESENTATION Working method ® Automower automatically mows the lawn. It continuously combines mowing and charging. The charging station sends out a signal that ® Automower can sense at a distance of 6 - 7 metres. The mower starts to search for the charging station when the battery charge becomes too low. ® Automower does not mow when it is searching for the charging station. ® When Automower searches for the charging station it uses one or more
Summary of the content on the page No. 14
2. PRESENTATION ® The control panel on the top of Automower is where you manage all the mower settings. The main switch is also located on the control panel. Open the control panel cover by pressing down the STOP button. When the main switch is turned ON for the first time, a start-up sequence begins which includes: selection of the language, time format, date format and four digit PIN code, plus setting of the time and date, see page 31. The selected PIN code must then be entere
Summary of the content on the page No. 15
2. PRESENTATION 2.3 Search method ® Automower can be set to search for the charging station in three different ways. Using the setting options the three search methods can be combined to optimise the search for the charging station. The required search method or methods depends on the shape of the garden. Search method 1: Irregular ® Automower runs irregularly until it finds the charging station. This search method is best for an installation that has an open lawn and no narrow passages
Summary of the content on the page No. 16
2. PRESENTATION ® 2.4 More than one Automower in a garden ® If you install more than one Automower in the same area of lawn, each mower must have its own PIN code. A complete installation, including charging station, is required for each mower. The boundary wires for the different installations can be routed next to each other. Contact your dealer for further information. ® 2.5 One Automower in several gardens ® One Automower can easily be used for more than one garden, where each garden
Summary of the content on the page No. 17
3. INSTALLATION 3. Installation This chapter describes how you install Husqvarna ® Automower . Before starting the installation read the previous chapter 2. Presentation. Read the whole of this chapter too before starting the installation. How the installation is made also affects ® how well Automower will work. It is therefore important to plan the installation carefully. Planning is simplified if you make a sketch of the working area, including all obstacles. This makes it easier to see
Summary of the content on the page No. 18
3. INSTALLATION • Screws for the charging station (24) • Measurement gauge (25) • Connector for the loop wire (23) • Solderless coupler for the loop wire (26) Contact your dealer to purchase the following installation material: • Loop wire for the boundary wire and guide wire (19) • Staples (22) During installation you will also need: A hammer to knock the staples into the ground, combination pliers, and a straight spade if the boundary wire is to be buried. 3.2 Installation of the charging
Summary of the content on the page No. 19
3. INSTALLATION Consider the distance to a wall socket when choosing the position. The charging station should be connected to a 230V wall socket via the low voltage cable and transformer. The supplied low voltage cable is 20 metres long. Tip! It is possible to let the low voltage cable cross the working area. It must then be either stapled down or buried. In some cases there is a better positioning option for the charging station than close to a house wall or by the closest wall socket.
Summary of the content on the page No. 20
3. INSTALLATION Do not position the charging station so that the mower can come closer than 3 metres behind the charging station (for example on a narrow point). The mower will not then find the charging station. Installation and connecting the charging station 1. Position the charging station in a suitable spot. 2. Attach the charging station to the ground using the supplied screws. 3. Ensure the screws are secured all the way down in the countersink. IMPORTANT INFORMATION It is not perm
