Summary of the content on the page No. 1
Operator's Manual
968999283 / W21K, 968999284 / W21SK,
968999286 / W21SBK, 968999287 / W53SBEK
968999289 / W53SEK, 968999638 / W21KC
968999639 / W21SKC, 968999640 / W21SBKC
Please read the operator’s manual carefully and make sure you
English
understand the instructions before using the machine.
Summary of the content on the page No. 2
OPERATOR’S MANUAL 21" PUSH MOWER Introduction ............................................3 Maintenance ........................................ 30 General .................................................3 Maintenance Schedule ...................... 31 Driving and Transport on Public Roads 3 Before Each Use ............................... 31 Towing ..................................................3 Ignition System .................................. 31 Operating ................................
Summary of the content on the page No. 3
INTRODUCTION WARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower. Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance. WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or e
Summary of the content on the page No. 4
INTRODUCTION Introduction Congratulations Thank you for purchasing a Husqvarna Pro Push Mower. This machine is built for high performance and rapid mowing. This manual is a valuable document. Following the instructions (use, service, maintenance, etc.) can considerably increase the lifespan of your machine and even increase its resale value. If you sell your machine, be sure to give the operator’s manual to the new owner. The final chapter of this operator’s manual comprises a Service Journal.
Summary of the content on the page No. 5
INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer, see the certificate in the Service Journal in this operator’s manual. When you need spare parts or support in service questions, warranty issues, etc., please consult the f
Summary of the content on the page No. 6
SYMBOLS AND DECALS Symbols and Decals These symbols are found on the machine and in the operator’s manual. Study them carefully so that you know what they mean. WARNING! Xxxxxxx xxxx xxxxxxxx xxx x Xxxxx xxxxxx xx. xx xxxxxxxx xxxxx xxx xx. Used in this publication to notify the reader of a risk of personal injury, particularly if the reader should neglect to follow instructions given in the manual. IMPORTANT INFORMATION Xxxxxxx xxxx xxxxxxxx xxx xxx xxxx xxxxxx xx. Used in this publication to
Summary of the content on the page No. 7
SYMBOLS AND DECALS Read Shut off engine and Whole Severing Do not open or Keep a safe Operator´s remove spark plug body of fingers remove safety distance from Manual. wire before exposure and toes. shields while engine the machine. performing any to thrown is running. maintenance or objects. repair work. Moving sharp blades under cover can sever fingers. English-6
Summary of the content on the page No. 8
SAFETY INSTRUCTIONS Safety Instructions These instructions are for your safety. Read them carefully. This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. WARNING! This symbol means that important safety instructions need to be emphasized. It concerns your safety. General Use Read all instructions in this operator’s manual and on the machine before starting it. Ensure
Summary of the content on the page No. 9
SAFETY INSTRUCTIONS Do not put hands or feet near or under WARNING! rotating parts. Keep clear of the Engine exhaust and certain discharge opening at all times vehicle components contain Do not pull mower backwards unless or emit chemicals considered absolutely necessary. Always look down to cause cancer, birth defects, and behind you before and while moving or other reproductive system backwards. damage. The engine exhaust contains carbon monoxide, Slow down before turning. wh
Summary of the content on the page No. 10
SAFETY INSTRUCTIONS Always wear gloves when handling the blades. Never wear loose clothing that can get caught in moving parts. Use ear protectors to avoid damage to hearing. Stop the blade when crossing gravel drives, walks, or roads. Shut the engine off and wait until the blade comes to a complete stop before removing grass catcher. Disengage the self-propelled mechanism or drive clutch on mowers so equipped before starting the engine. If the equipment should start to vib
Summary of the content on the page No. 11
SAFETY INSTRUCTIONS Do not drive the mower on terrain that slopes more than 10°. Do not mow near verges, ditches, or banks. The operator could lose footing or balance. Do not mow wet grass. Reduced footing could cause slipping Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. Avoid starting or stopping on a slope. If the tires begin to slip, shut down the blades if so equipped or shut off the engine and move slowly down the slop
Summary of the content on the page No. 12
SAFETY INSTRUCTIONS Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device. Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling. Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with
Summary of the content on the page No. 13
SAFETY INSTRUCTIONS Never make adjustments with the engine running. Ensure that nuts and bolts, especially the fastening bolts for the blade attachments, are properly tightened, torqued and that the equipment is in good condition. Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be used with defective or unmounted protective plates, protective cowlings, safety switches, or other protective devices. Do not change the settings of g
Summary of the content on the page No. 14
SAFETY INSTRUCTIONS Check and abide by local traffic regulations before transporting. Do not tow this machine, it may cause damage to the drive system. Customer responsibilities Read and observe the safety rules. Follow a regular schedule in maintaining, caring for and using your mower. Follow the instructions under “Maintenance” and “Storage” sections of this owner’s manual. WARNING! This mower is equipped with an internal combustion engine and should not be used on or near any
Summary of the content on the page No. 15
CONTROLS Controls This operator’s manual describes the Husqvarna Pro Push Mower. The mower is fitted with a Kawasaki engine. 8019-040 Pro Push Mower Control Locations 7 8 9 8 11 8 1, 5, 6 4 10 3 2 8 8019-052 Locations of the controls Page Page 1 Engine speed 14 7 BBC control 16 2 Fuel shut off valve 14 8 Cutting height 16 3 Fuel tank cap 14 9 Ground Speed Bail 17 4 Operator presence control (OPC) 14 10 & 11 Engine shut off 18 5 Choke control 15 6 Throttle control 15 English-13
Summary of the content on the page No. 16
CONTROLS Engine Speed CAUTION: The engine speed was set at the factory for Federal regulations require an optimum performance. Speed is not engine control to be installed adjustable on this lawn mower in order to Operator Presence Control (OPC) minimize the risk of blade contact injury. DO NOT under Models: W21SBK, W53SBEK, W21SBKC any circumstances attempt to Your lawn mower is equipped with an defeat the function of the operator presence control (OPC). The engine operator control. T
Summary of the content on the page No. 17
CONTROLS . WARNING! Gasoline is highly flammable. Observe caution and fill the tank outdoors (see the safety rules). IMPORTANT INFORMATION Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which WARNING! leads to separation and formation of Fill to bottom of filler neck. Do acids during storage. Acidic gas can not overfill. Wipe off any damage the fuel system of an engine spilled oil or fuel. Do not store, while in storage. To
Summary of the content on the page No. 18
CONTROLS Blade Brake Control (BBC) Models: W21SBK, W53SBEK, W21SBKC The Blade Brake Control (BBC) engages the blade drive. The Operator Presence Control (OPC) must be engaged and the engine 1 running to engage the BBC. 3 Illustration shows ground speed bail engaged to operate in transport mode. Release ground speed bail to prevent movement. 2 Operator Presence Control (OPC) 8019-037 1. OPC 2. BBC 3. Ground speed bail To engage BBC, press the control forward as shown in illustration. 8019
Summary of the content on the page No. 19
CONTROLS Cutting height 2 The cutting deck height is obtained by raising the wheels for low cut and lowering wheels 1 for high cut, adjust cutting height to suit your requirements. Medium position is best for 3 most lawns. To change your cutting height, squeeze adjuster lever toward wheel. Move wheel up or down to suit your requirements. Be sure all 8019-038 8019-039 1. Lever backward to lower mower wheels are in the same setting. Lever forward to raise mower NOTE: Adjuster is properly p
Summary of the content on the page No. 20
CONTROLS Shut Off Engine 2 Models: W21SBK, W53SBEK, W21SBKC To stop engine, release OPC bail to stop blades. Pull back on throttle control to stop 1 engine 8019-047 Stop Engine 1. OPC bail 2. Throttle control 2 Models: W21SK, W53SEK, W21SKC Pull throttle control back to slow speed. Release OPC bail to stop engine. 1 8019-020 Stop Engine 1. OPC bail 2. Throttle control 2 Model: W21K, W21KC Pull throttle control back to slow speed. Release OPC bail to stop engine. 1 8019-048 Stop Engine 1. OPC
