Summary of the content on the page No. 1
INSTALLATION AND OPERATION INSTRUCTIONS
CONCESSIONAIRE PORTABLE DISPENSERS
MODEL NOS.
DC Series
IMPORTANT INFORMATION Table of Contents
Complete the enclosed warranty card and mail to the
PREPARING THE CABINET FOR USE
Perlick Corporation to register the warranty. If the
Specifications.........................................................2
card is not returned, the warranty period will begin
List of Included Parts.............................................3
from the date the equipment is shi
Summary of the content on the page No. 2
Installation and Operating Instructions Sizes and Specifications, Concessionaire Dispensers MODEL NOS. DC2KP DC3KP DC4KP KEG CAPACITY 2 Keg 3 Keg 4 Keg DIMENSIONS Length Ins. (mm) 72” (1829) 84” (2134) 96” (2438) 1 1 1 CABINET Depth Ins. (mm) 24 /8” (613) 24 /8” (613) 24 /8” (613) 1 1 1 Height Ins. (mm) 34 /2” (876) 34 /2” (876) 34 /2” (876) NO. OF DISPENSING HEADS 1 1 2 NO. FAUCETS 2 2 2 1 1 1 CONDENSER UNIT H.P. /4 /3 /3 RUNNING LOAD - AMPS 5.9 7.5 7.5 SHIP WT lbs. (kg) 445 (202) 505 (229) 545
Summary of the content on the page No. 3
Preparing the Cabinet for Use – Concessionaire Dispensers Parts List Plumbing Faucet Standard. None required. Garden hose connections for dumping Faucet Head Assembly liquid wastes. Caster Set. Electrical 3 Black Connector Hose ⁄16” x 3’. 5 The cabinet must be connected to a separately ⁄16” Air Hose. fused power source (see electrical specification Spanner Wrench. plate) and grounded in accordance with National Bag of Miscellaneous Parts. and Local Electrical Codes. Caution: Do not
Summary of the content on the page No. 4
Installation and Tapping – Concessionaire Dispensers Connecting the Keg Coupler Tapping a Single Valve Keg (Sankey): (when Supplied by Perlick) Place one brown leather washer into black beer line connector hose on hex nut side. Screw Step 1 connector to stainless steel beverage line on faucet standard. Tighten with a wrench, but do not over tighten. Single Valve Keg Coupler Make sure lever handle on the keg coupler is in the UP (untapped) position. Place one brown leather washer into w
Summary of the content on the page No. 5
Installation and Tapping – Concessionaire Dispensers Unscrew regulator from cylinder fitting. Connecting the Regulator to the Replace carbonic washer (Part No. 157F2P), CO2 Cylinder if needed and reattach regulator to filled Remove blue plug from regulator fitting. cylinder. (Note: Do not remove the carbonic washer). Turn CO2 hand valve counterclockwise until Screw regulator onto gas cylinder valve. Tighten fully open. Turn regulator shut-off valve to with wrench until vertically
Summary of the content on the page No. 6
Draft Beer Information – Concessionaire Dispensers Temperature One of the most common causes of dispensing At temperatures lower than 30° F., beer will freeze. When beer freezes, the alcohol in the beer may problems is improper temperature. Draft beer separate and cause the beer to be cloudy with an should be stored at a temperature between 32° and 38°. At warmer temperatures, beer will foam. “off” taste. Refrigeration and Temperature Control Adjusting the temperature The Direct Draw Dispenser
Summary of the content on the page No. 7
Cleaning the Beer System – Concessionaire Dispensers The entire beer system, to include the faucet, flexible Beer Stone: beer line and tapping devices must be cleaned at All beer contains calcium which is present from regular intervals. We recommend flushing the entire the grains used in the brewing process. it is an system with fresh water immediately after a keg has important natural material in draft systems in been emptied. Once each month the system should that as it oxidizes it coats
Summary of the content on the page No. 8
Pouring a Perfect Glass of Beer – Concessionaire Dispensers ➠ STEP 1 Start with a clean glass. Place the glass at a 45° angle, one inch below faucet. Do not let the glass touch the faucet. Open the faucet all the way. STEP 2 ➠ After the glass has reached half full, gradually bring the glass to the upright position ➠ STEP 3 Let the remaining beer run straight down the middle of the glass. This ensures proper release of CO2 by 3 producing a ⁄4” to 1” foam head. STEP 4 ➠ Close the faucet quickly
Summary of the content on the page No. 9
Trouble Shooting – Concessionaire Dispensers Beer Service Problems Cloudy Beer: Beer in glass appears hazy, not clear. Wild Beer: CAUSES: Dispensed beer has either too much foam or Dirty glass. is all foam. Dirty faucet or beer line. CAUSES: Frozen or nearly frozen beer. Beer has been dispensed improperly. Old beer. Solution: See pouring instructions Beer that has not been refrigerated for a on page 8. long period of time. Regulator pressure is set too high. Warm keg temper
Summary of the content on the page No. 10
Replacement Parts – Concessionaire Dispensers MODEL NOS. DC2KP DC3KP DC4KP All Models Left hinged door assembly 64357SLBL 64357SLBL 64357SLBL Right hinged door assembly 64357SRBL 64357SRBL 64357SRBL Magnetic door gasket 62085-1 62085-1 62085-1 Hinge set, left 63407L 63407L 63407L Hinge set, right 63407R 63407R 63407R 3 1 Elbow-nylon ⁄4” F.P.T. x ⁄2” barb 57736-1 57736-1 57736-1 1 ⁄2” trans vinyl beverage tubing 8.7 ft. 1390TR 1390TR 1390TR Glass rack C24639-1 C24639-1 C24639-1 Bulb clamp C6634 C
Summary of the content on the page No. 11
Replacement Parts – Concessionaire Dispensers For Single Valve Keg Coupler (Series D) Item Part No. No. Description 1 2 1 ............26000D ..............Single valve keg coupler 2 ............C14316 ..............“O” ring 3 3...........31080-2P.............Ball check 4...........31089-2P.............“O” ring (3 per assembly) 5...........31088-2P.............Bottom seal washer 4 6...........31087-2P.............Probe washer domestic 7............157R2P ..............Coupling Gasket 8..........
Summary of the content on the page No. 12
Wiring Diagram – Concessionaire Dispensers 8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069 Toll Free 800-558-5592 • E-Mail: Perlick@Perlick.com • www.Perlick.com Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice. Form No. Z2060A Rev. 12.05.03 12
