Snapper 75438 user manual

Summary of the content on the page No. 1

#6-3318 TWIN BAG GRASS CATCHER KIT for
SNAPPER 28" & 33" REAR ENGINE RIDERS & 33” LAWN TRACTORS

This grass catcher kit fits Lawn Tractors with 33” Decks and Rear Engine Riders with 28” & 33” Decks. On
Series “A” & Later Lawn Tractors, Adapter Kit #6-1334 must be installed before this grass catcher can be
installed. On Series “0-2” Lawn Tractors, Adapter Kit #6-1068 must be installed before this grass catcher can
be installed. Install adapter kit as described by instructions provided with

Summary of the content on the page No. 2

WARNING DO NOT operate machine without entire grass catcher or guards in place. STEP 4: ADAPTER INSTALLATION Hold the adapter in front of the deck. Align the adapter lugs with the hinge lug retainers, then push the adapter to the rear. Loosen bolts (see Figure 4) & bump the adapter, if necessary, to force the lugs under the lug retainers. Secure the adapter to the deck with the previously removed bolt, flat washer and wing nut (from step 2). Tighten bolts. See Figure 4. FIGURE 5

Summary of the content on the page No. 3

STEP 8: Bag Installation. Insert both grass bags onto STEP 10: Grass Tube Installation frame. Make sure the grass bag frame notches fit into Slide upper end of grass tube into opening of cover/frame the frame recesses. See Figure 8. structure. Slide lower end of grass tube over adapter end and rotate tube towards mower to secure handle hook under latch. See Figure 10. FIGURE 8 STEP 9: Bag Installation. Lower cover assembly onto frame. Lift up hook and insert it into hole in cover

Summary of the content on the page No. 4

WARNING Weight Plates must be installed before operating the machine with a grass catcher kit. Grass catchers and other attachments affect the handling and stability of the machine. Use extra care. Refer to the Operator’s Manual for IMPORTANT SAFETY INSTRUCTIONS STEP 12 DRILL MOUNTING HOLES (SERIES M RIDERS ONLY) Measure and mark the location of the two holes using dimensions shown. See Figure 12. Drill two 13/32” holes. Attach weight plates. Refer to S

Summary of the content on the page No. 5

TWIN BAG GRASS CATCHER ILLUSTRATION 5

Summary of the content on the page No. 6

TWIN BAG GRASS CATCHER PARTS LIST ITEM PART NO. DESCRIPTION 1 5-3668 COVER Assembly 2 1-9966 INLET 3 1-9725 SECTOR (Inside top baffle) 4 5-9951 MOUNTING Assembly (Includes following indented item) - 3-6263 HOLDER, Inlet 5 5-1407 SPRING & Hook Assembly 6 3-6073 BRACE 7 9-1612 BOLT, 5/16-18 x 1-1/2” Carriage (2) 8 3-8087 HINGE, Top (2) 9 9-1611 SCREW, 1/4-28 x 3/4 Hex Head Cap (4) 10 9-1606 NUT, 5/16-24 Hex Center Lock (2) 11 2-3797 PAD, Bumper (2) 12 9-1605 NUT, 1/

Summary of the content on the page No. 7

GRASS CATCHER OPERATION Your Grass Catcher equipped SNAPPER machine will keep your lawn cleaner than it would be by raking or using any other vacuum method. The Hi-Vac models, which feature a patented rolled-lip deck design, will do an excellent job of vacuuming and bagging grass clipping, leaves, litter, and even hard to pick-up pine straw. Following are some hints for using the grass catcher. • Grass clippings and litter are picked up by the vacuum created by the cutter blade and bl