Summary of the content on the page No. 1
ORDER No.AD0101008C2
Portable MD Player
SJ-MJ88
MD unit: RAE1611Z Mechanism Series
Colour
(S)...................Silver Type
Areas
EB...................Great Britain.
EG...................Europe.
1
Summary of the content on the page No. 2
SPECIFICATIONS Specifications Audio System: MiniDisc digital audio system Laser: Semiconductor laser (=780 nm) Sampling frequency: 44.1 kHz Coding: Adaptive Transform Acoustic Coding (ATRAC) No. of channels: 2 (left and right, stereo) 1 (monaural) Frequency response: 20 Hz~20 kHz (+0 dB, -8dB) Wow and flutter: Below measurable limit General Output terminal Output Jack: Phones, 22 Power output: 3.5 mW+3.5 mW Power supply Rechargeable DC 1.2V battery: (included rechargeable battery) Ba
Summary of the content on the page No. 3
Panasonic About 70 alkaline: hours Both together: About 88 hours Charger Input: AC120-240 V (EG) / AC 230-240V (EB), 50 Hz 4W Output: DC 340mA (EG)/DC 350mA (EB), 1.2V Recharging time: About 2 hours Notes: - The play time may be less depending on the operating conditions. - Specifications are subject to charge without notice. Weight and dimensions are approximate. 1 1. Accessories - Stereo earphones...................................................1 pc. (L0BAB0000162) - Wired remote co
Summary of the content on the page No. 4
- Carrying case..........................................................1 pc. (RFC0056-K) For EB area - Charger...................................................................1 pc. (RP-BC155AEBY) For EG area - Charger...................................................................1 pc. (RP-BC155AEYB) 2. Precaution of Laser Diode 4
Summary of the content on the page No. 5
3. Operating Instructions 4. Handling Precautions for Traverse Deck The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup). 4.1. Handling the traverse deck (optical pickup) 1. The traverse deck (optical pickup) is an extremely high-precision construction and must not be subjected to impact, excessive vibr
Summary of the content on the page No. 6
Fig. 1 Fig. 2 4.2. Grounding for electrostatic breakdown prevention 1. Human body grounding 6
Summary of the content on the page No. 7
Use the anti-static wrist strap to discharge the static electricity from your body. (as shown in Fig. 3 ) 2. Work table grounding Put a conductive material (sheet) or steel sheet on the area where the traverse deck (optical pickup) is placed, and ground the sheet. (as shown in Fig. 4 ) Caution The static electricity of your clothes will not be grounded through the wrist strap. So, take care not to let your clothes touch the traverse deck (optical pickup). Fig. 3 Fig. 4 7
Summary of the content on the page No. 8
5. Operation Checks and Component Replacement Procedures - This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components. - For reassembly after operation checks or replacement, reverse the respective procedures. Special reassembly procedures are described only when required. - After replacing the main components (optical pickup or traverse motor, etc.) of mechanism unit block, change to the adjust mode, and then perform t
Summary of the content on the page No. 9
9
Summary of the content on the page No. 10
- Check the P.C.B. as shown below. 10
Summary of the content on the page No. 11
5.2. Replacement for the lock unit, open knob and intermediate cabinet - Follow the (Step 1) - (Step 3) of item 5.1. 11
Summary of the content on the page No. 12
12
Summary of the content on the page No. 13
13
Summary of the content on the page No. 14
14
Summary of the content on the page No. 15
5.3. Replacement for the disc cover ass’y - Follow the (Step 1) - (Step 3) of item 5.1. - Follow the (Step 1) - (Step 3) of item 5.2. 15
Summary of the content on the page No. 16
5.4. Replacement for the traverse motor - Follow the (Step 1) - (Step 3) of item 5.1. 16
Summary of the content on the page No. 17
17
Summary of the content on the page No. 18
18
Summary of the content on the page No. 19
19
Summary of the content on the page No. 20
5.5. Replacement for the optical pickup - Follow the (Step 1) - (Step 3) of item 5.1. - Follow the (Step 1) - (Step 5) of item 5.4. 20
