Summary of the content on the page No. 1
®
GE Monogram
Installation
Instructions
Under Cabinet Installation
and
JX827WN Built-In Kit
Microwave Oven
Model
ZEM200WV
Summary of the content on the page No. 2
Before you begin—Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector’s use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future reference. This appliance must be properly grounded. See “Electrical Supply”, page 6. CAUTION WARNING If you have questions concerning the installation of Proper
Summary of the content on the page No. 3
Design Information Microwave Oven ZEM200WV Model available White electronic microwave oven Designed for versatility, this Monogram microwave oven adapts to virtually any installation. Accessory kit JX827WN is required for custom in-wall installation. ZEM200WV Dimensions and clearances A - 12 -5/16" (284 mm) B - 23-13/16" (605 mm) C - 11-3/16" (284 mm) (includes feet) Note: When installed, trim kit will require wall space 26-1/8" W x 16-1/4" H for clearance. Wall Cutout ZEM200WN Installation This
Summary of the content on the page No. 4
Installation Preparation Microwave Oven ZEM200WV Tools and materials required: In-wall •3/8" thick plywood (min.) installation •2" x 4" lumber •Saw •Screws and screwdriver or other hardware for construction of plywood base. Opening for model ZEM200WV must be: • 24 -7/8" ± 1/16" wide. • 15" ± 1/16" high. • With approximately 1-1/4" for oven trim overlap around all edges of opening. • Deep enough to accommodate electrical receptacle and permit adequate air circulation for proper venting: – Minimum
Summary of the content on the page No. 5
Installation Preparation Microwave Oven ZEM200WV Refer to diagram at right With single for dimensions when oven installing ZEM200WV above a Monogram single oven. Note: Trim kit JX827WN is required for installation above a single oven. Within opening of appropriate dimensions: • Install a level base of plywood: – Flush with lower edge of opening. – Entirely covering floor of opening. • 3/8" thick (min.) plywood must be supported by 2" x 4" or 1" x 2" equivalent runners on all four sides. • Finish
Summary of the content on the page No. 6
Installation Preparation Microwave Oven Electrical Tools and materials required: supply •3-prong grounded electrical receptacle. •Electrical cable, 2-wire with ground, No. 14 minimum, as required. Monogram microwave ovens require a 120 volt, 60 Hz power supply, protected by a time delay fuse or circuit breaker. ZEM200WV oven is supplied with a power cord 57" long for which a properly grounded 3-prong electrical receptacle is required. • 800 watt* oven ZEM200WV draws 1360 watts, with a 13 amp loa
Summary of the content on the page No. 7
Installation Preparation Microwave Oven ZEM200WV • When cabinet depth is a critical factor, receptacle In-wall should be installed in a side wall at rear of opening: installation – 14 -5/8" minimum cabinet depth is required. (continued) Receptacle installed in side wall. • If receptacle is located behind oven, install receptacle flush with wall to minimize depth: – 16" minimum depth is required. Receptacle installed behind oven, flush with wall. • If receptacle is located behind oven and extende
Summary of the content on the page No. 8
2 3 3 Installation Microwave Oven JX827WN Tools and materials installation required: •Accessory kit JX827WN for 7 4 in-wall installation of 5 ZEM200WV D 6 B A •2 Phillips head screwdrivers 1 (#1 & #2) E C •Drill and 3/32" drill bit •Centerpunch or nail •Pencil and ruler Parts Inventory JX827WN Parts List 1. Base Pan 2. Rear Duct 3. Side Covers (2) 4. Top Trim 5. Bottom Trim 6. Side Trims 7. Rear Holddown Brackets Screws A (9 required 1 extra) Screw A Screw B Screw C Screw D Screw E B (4 required
Summary of the content on the page No. 9
Installation Microwave Oven JX827WN installation • Remove the four top plug buttons from the top of the microwave oven cabinet. • Place the microwave oven on the base pan centered left to right. Note: Do not tighten screws until all screws are started. • Install side cover by inserting between oven and base pan. • Start two screws A, through side cover and two screws E, through the cover on top into holes where buttons were removed. • Install other side cover with screws A. • Install other top s
Summary of the content on the page No. 10
Installation Microwave Oven JX827WN installation Screw A • Install rear duct by inserting into bottom flange • Drive one screw into the rear duct side flange near between the oven and back of base pan. the lamp cover. – The rear duct should be as far to the left as • Drive three screws through the base pan into the possible, between the base pan back flange and rear duct bottom. the partition on the right side. • Replace the screw removed from the top left to • Locate and use screws A. complete
Summary of the content on the page No. 11
Installation Microwave Oven Assemble • Assemble top, bottom trim kit and side trims with four frame screws D, as illustrated. Screw D When assembled, top, bottom and side strips must be flush. Note: Bottom trim has a hinge notch and is not interchangable with top trim. Install trim kit frame Caution: Do not overtighten screws; doing so could cause misalignment of top and side strips. Screw C • Use the assembled frame as a template. Insert the • Mark the four holes on the side of the trim. frame
Summary of the content on the page No. 12
Installation Microwave Oven ZEM200WV Tools and materials Under-cabinet required: mounting •Flat-blade screwdriver •Phillips screwdriver •Drill and 1/4" bit •Nail or center punch •Pencil and ruler •Scissors •Hammer •Tape •Line cord holder (supplied) •Two brackets (supplied) 15 13/32" Template 1 3 /4 1/2 1 /4 Template 2 Mounting holes for the oven should be drilled from • Carefully remove the four plastic plug buttons from oven top and the two screws at top rear flange of case. the inside, if cabi
Summary of the content on the page No. 13
Installation Microwave Oven To drill from inside (continued) – Position remaining piece of Template 2 inside cabinet • With template secured in place, check again that and align hole center line with arrows on Template 1. hole center lines on Template 2 are straight, and – Cut excess paper from center of Template 2 so it will that distance from right to left hole center measures lie flat. distance shown on template. – Distance from right hole center to left hole center should measure distance in
Summary of the content on the page No. 14
Installation Microwave Oven Finalize under-cabinet installation 13/16" • With template secured in place, check again that hole • Select four bolts—one of each size—from parts center lines on Template 2 are straight, and that package. distance from right to left hole center measures • Hold each bolt against cabinet front rail. distance shown on template. • Select bolt that extends beyond top of bottom shelf • Drill mounting holes: by 3/16" to 13/16". – Use of safety glasses is recommended to prot
Summary of the content on the page No. 15
Notes Microwave Ovens 15
Summary of the content on the page No. 16
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any ® Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night. For Monogram local service in your area, call 1-800-444-1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are Pub. No. 49-8799 subject to change with
