Summary of the content on the page No. 1
INSTALLATION
INSTRUCTIONS
Oven
F o r B u i l t - i n M i c r o w a v e O v e n s
Model
MBB
Built-In
Trim Kits
Models:
MT27B
MT30B
(Sold Separately)
Summary of the content on the page No. 2
Please read this entire manual before proceeding IMPORTANT: Local codes vary. Installation, electrical connections, circuit breakers and grounding must comply with all applicable codes. Save these instructions for your local electrical inspector's use. INSTALLER: Please leave these Installation Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. WARNING: Disconnect power at the breaker before installing. Table of Contents Step 1: Unpacking ..
Summary of the content on the page No. 3
Step 1: Unpacking A. Microwave Oven Model MBB Open the box and carefully remove all fillers and packing material. Your new Thermador microwave includes the following: • Care & Use manual (1) • Quick Guide (1) • Warranty Card (1) • Turn Table (1) • Turn Table Support (1) B. Trim Kit Models MT27B & MT30B Open the box and carefully remove all fillers and packing materials. Parts list: Table 1 • Trim Frame (1) • Base Pan (1) Trim Kits Microwave Ovens • Trim Bracket (2) • Side Duct (1) 30" cabine
Summary of the content on the page No. 4
Step 2: Cabinet Preparation • The cabinet cutout dimensions are shown in • Your microwave oven can be installed into a Figure 1. cabinet or wall by itself or above any of the following Thermador wall ovens: C271, C301, • It is a good practice when the microwave oven CM301, S301, SC301. Or, Thermador Warm- is installed at the end of a cabinet run, adja- ing Drawers WD27 and WD30 (see Figure 2). cent to a perpendicular wall or cabinet door, 1 • Outlet can be located anywhere within the to allow
Summary of the content on the page No. 5
Step 3: Electrical Installation The Thermador microwave oven is equipped with a grounded cord. The wall receptacle must be installed and grounded in accordance with the national electrical code. Also, electrical connections and grounding must comply with all applicable local codes. The electrical requirements for a separate circuit serving only this microwave oven are: 120V, 60Hz, 20Amps Step 4: Installing the Trim Kit Position the two vertical trim brackets using the template as shown on Fi
Summary of the content on the page No. 6
Step 5: Installing The Microwave Oven Note: The four (4) ducts have a plastic cov- 3. Position Side Duct on left side of oven. Fasten with outer case screw removed in ering that must be removed prior to install- ing them onto the microwave. Step 2. 4. Position Upper Exaust Duct on top (hinge side) of oven and fasten it together with Side 1 WARNING Duct by using two (2) screws #8 x /4". 5. Remove and retain Outer Case Screw at rear These ducts have sharp edges. Be care- of the oven (right side).
Summary of the content on the page No. 7
Step 5: Installing The Microwave Oven (continued) 9. Remove the left side vertical trim bracket (three screws) (MT27B only). 10. Slide the assembled microwave oven part way into the prepared cabinet cutout. Plug the electrical cord in the wall recep- tacle (ask for help from another person). Slide oven in the rest of the way into the cabinet. Position base pan on cabinet shelf with respect to the center line as shown on Figure 5. The front end of pan should align flush with the front edge of t
Summary of the content on the page No. 8
Thermador reserves the right to change specifications or design without notice. Some models are certified for use in Canada. Thermador is not responsible for products which are transported from the United States for use in Canada. Check with your local Canadian distributor or dealer. Thermador, 5551 McFadden Avenue, Huntington Beach, CA 92649. For the most up-to-date critical installation dimensions by fax, use your fax handset and phone 702/833-3600. Use code #8030. BSH Home Appliances Corpora
