Summary of the content on the page No. 1
DSL-100D
ADSL PCI Modem
User’s Guide
First Edition Version 2 (April 2001)
6DSL100D..02
Summary of the content on the page No. 2
Summary of the content on the page No. 3
TABLE OF CONTENTS ABOUT THIS GUIDE .........................................................................................................................................II PURPOSE.............................................................................................................................................................. II BEFORE YOU BEGIN.......................................................................................................................................
Summary of the content on the page No. 4
About This Guide ® Congratulations on your purchase of the ADSL PCI Modem Card for Windows 95, 98, 2000 Me and NT 4.0. This internal modem card connects to a telephone line using a standard RJ-11 connector and follows all the latest PC industry guidelines, including Plug and Play. Purpose The purpose of this manual is to discuss the installation and use of your ADSL PCI Modem Card. Before you Begin This manual has all the information you need to install and configure the PCI Modem card
Summary of the content on the page No. 5
Introduction This section describes the ADSL PCI modem card, its features, and system requirements. Features The ADSL PCI Modem Card is an internal PCI device designed for use with Windows 95, 98, 2000, Me and NT 4.0. This modem card connects to an ADSL/telephone line using a standard RJ-11 connector and follows all the latest PC industry guidelines, including Plug 'n Play. For added convenience, an additional RJ-11 receptacle provides an outlet for a standard telephone or fax machine.
Summary of the content on the page No. 6
Operating Systems: • Windows 95, 95 OSR2 • Windows 98, 98 Second Edition • Windows 2000 • Windows Me • Windows NT 4.0 NOTE: You will need the original Windows operating system installation CD-ROM to complete the installation. The installation procedure varies according to the operating system you are using. It is critical that you use the correct installation procedure for your operating system. Gather Information To make connecting and configuring your modem as easy and straightfor
Summary of the content on the page No. 7
Internet Service Protocol Your Internet Service Provider (ISP) uses one of the protocols listed below. Look over the information provided by your ISP or call their technical support if you are not sure which protocol they are using. • RFC 2364 Point-to-Point Protocol over ATM • RFC 1483 Multi-protocol Encapsulation over ATM, a.k.a. “Bridged Ethernet” • RFC 1577 Classical Internet Protocol over ATM Connection Address and Configuration You need to know the connection address and configur
Summary of the content on the page No. 8
Configuration Form Before beginning the installation, photocopy or print this page and fill out the form provided. Refer to this form when you reach the Service Options panel and enter the proper configurations. ADSL COMMUNICATION SETTINGS: Protocol: RFC 1483 Multi-protocol Encapsulation over ATM RFC 2364 Point-to-Point Protocol over ATM RFC 1577 Classical Internet Protocol over ATM VPI value: VCI value: Framing: LLC/SNAP VC MUX ADSL Mode: ANSI T1.413 I
Summary of the content on the page No. 9
Step 1 Hardware Installation The card must be installed on the computer’s motherboard. Since this is an electrical device, safety is important. First, properly shutdown the computer and unplug the computer’s power cord. Touch an unpainted screw on the back of the power supply with the tip of your screwdriver to discharge any static electricity and prevent possible damage to the card and computer components. Open the computer’s case. Insert the card into an open PCI slot. Insert the ca
Summary of the content on the page No. 10
Step 2 Software Installation and Configuration Windows will automatically detect new hardware when it is added to the computer. The Add New Hardware Wizard will appear to guide you through the Software Installation. In order for the Modem to work you must configure it properly. The following sections show you the steps. You must enter the proper configurations for the DSLAM. You will enter one of the following: • VPI • VCI • Framing Method • ADSL Mode The Digital Subscriber Line A
Summary of the content on the page No. 11
Windows 98/98SE Driver Installation 1. The Add New Hardware Wizard window automatically appears and indicates that the new PCI Network Controller (PCI Modem) has been found. Click Next. 2. Still in the Add New Hardware window, you will be asked ‘What do you want Windows to do?’ Select ‘Search for the best driver for your device,’ then click Next. 3. Insert the driver CD. 4. Choose “Specify a location” and click Browse. 7
Summary of the content on the page No. 12
5. Find the folder 1483w98, 1577w98, or 2364w98 (according to the protocol used by your ISP) on the CD-ROM drive and click OK. 6. Again the Add New Hardware Wizard window appears indicating the location of the driver. Click Next to install the driver. 8
Summary of the content on the page No. 13
7. After the driver has finished installing, click Finish. 8. You must restart the computer to finish the installation. You can do that now if you wish. 9. If you install the RFC2364 (PPPoA) driver, after you restart, the Location Information window appears automatically. Choose the country and enter the area code where you are located. Click Close when you are finished. You next need to configure the device. Proceed to the section on Configuration. 9
Summary of the content on the page No. 14
Windows 95 Driver Installation If you want to install the RFC2364 (PPPoA) driver, you must upgrade the Dial-Up Networking Application. The self-executing file is located on the Driver CD. The file name is ‘MSDUN13.EXE’. Double-click on this file to update Dial-up Networking. You will be prompted to restart your computer after running the application. After you install the modem, start the computer and the follow these instructions. 1. The Update Device Driver Wizard prompts you to begi
Summary of the content on the page No. 15
3. In the Select Other Location window, click Browse to search for the driver on your CD- ROM drive. 4. Find the folder 1483w95, 1577w95, or 2364w95 (according to the protocol used by your ISP) on the CD-ROM drive. Click OK. 11
Summary of the content on the page No. 16
5. The driver is now ready to be installed. Click Finish to install it. 6. You must restart the computer to finish the installation. After you have restarted, you will next need to configure the device. Proceed to the section on Configuration. Windows 2000 Driver Installation 1. The Found New Hardware Wizard window will automatically appear. Click Next. 12
Summary of the content on the page No. 17
2. The Found New Hardware Wizard explains that it can install the driver for the Network Controller (PCI Modem). Select “Search for a suitable driver…” and click Next to proceed. 3. You will be asked where you want the computer to search for the driver. Select the “Specify a location…” option. Insert the Driver CD and click Next. 4. Click Browse to search the CD for the driver folder. 13
Summary of the content on the page No. 18
5. Find the folder 1483w2k, 1577w2k, or 2364w2k (according to the protocol used by your ISP) and double-click on it to open it. Or highlight it and click Open. 6. Click Open to proceed to the next window. 14
Summary of the content on the page No. 19
7. The driver folder location will now appear in the Found New Hardware Wizard window. Click OK. 8. The driver is now ready to be installed. Check to be sure the driver file path is correct and click Next. 9. A warning appears telling you the Microsoft digital signature has not been found. D-Link has thoroughly tested the driver for Windows 2000. Click Yes to continue. 15
Summary of the content on the page No. 20
10. Windows has completed the driver installation. Click Finish and proceed to the Configuration section of this guide. Windows ME Driver Installation 1. The Add New Hardware Wizard window will automatically appear and indicate that the new PCI Network Controller (PCI Modem) has been found. Click Next. Insert the driver CD into the CD-ROM drive. 2. Still in the Add New Hardware window, select “Search for the best driver for the device option”, then choose “Specify a lo
